PXI Backplanes
-
Product
PXI Single SP4T Multiplexer 40GHz 50 SMA-2.9
40-784A-141
-
Pickering Interfaces’ range of 40-784A PXI Microwave Multiplexer Modules have a characteristic impedance of 50Ω and are capable of switching signals up to 40GHz. Available in single, dual or triple, SP6T or SP4T formats, they are suitable for constructing complex microwave switching networks and provide a range of switching configurations to suit most applications. Connection is by high performance front panel mounted SMA or SMA-2.9 connectors
-
Product
PXI Waveform Digitizer
PXD731x/70xx
-
Digitize high-resolution waveforms with the fully isolated PXD Series digitizers. Minimize interference and measure "in-circuit" within circuits. Measurement errors are reduced by a high input impedance.
-
Product
PXI High Density MUX BRIC, 12-Chan, 40-Pole
40-570-213
-
This range of High-Density Multiplexer is part of our BRIC family. These MUX's are designed to simplify the connection of a common set of test equipment to one of a number of different devices for testing (simultaneous multiple channel selection is also possible, without limitation). These multiplexers are ideal for applications where the equipment needs to conduct the same test process on a series of similar devices one at a time. They are available in a variety of configurations that allow testing with differing number of devices to be tested and different connection widths to suit differing test equipment pin counts. All version are supported in a BRIC8 construction that occupies eight PXI 3U mechanical slots, one of which provides the PXI interface and power.
-
Product
3U 12-slot VPX Backplane Aligned To SOSA 1.0
1OVX312AFQ-xxxx
-
3U 12-slot backplane with profiles aligned SOSA. It is designed to meet the U.S. Army’s C5ISR Modular Open Suite of Standards (CMOSS), and supports high-speed signals on all data paths and VITA 67.3 and VITA 66.5 connectors.
-
Product
PXIe-5624, 2 GS/s, 12-Bit PXI IF Digitizer
783132-01
-
The PXIe‑5624 is optimized for superheterodyne receiver architectures. It features an onboard digital downconverter, which converts IF signals to I/Q data. As a result, you can use the PXIe‑5624 either as part of a PXI Vector Signal Analyzer or as a stand-alone IF digitizer.
-
Product
PXI 2A Multiplexer, 1-Bank, 32-Channel, 4-Pole
40-614B-017
-
This 1-bank, 32-channel, 4-pole version is part of the 40-614B High Density 2A multiplexer module range that is available in 20 configurations (see Also in this Range link above). All configurations use high quality electro-mechanical signal relays allowing each channel to switch current up to 2A and voltage up to 300VDC/250VAC.
-
Product
PXI 2A Multiplexer, 2-Bank, 16-Channel, 4-Pole
40-614B-012
-
This 2-bank, 16-channel, 4-pole version is part of the 40-614B High Density 2A multiplexer module range that is available in 20 configurations (see Also in this Range link above). All configurations use high quality electro-mechanical signal relays allowing each channel to switch current up to 2A and voltage up to 300VDC/250VAC.
-
Product
PXI Simulation Modules For Sensor Simulation
-
PXI simulation solutions for sensor simulation, including PXI Programmable Resistors—ideal for the simulation of resistive sensors and PXI Thermocouple Simulators—these provide multiple low-voltage sources ideal for simulating the operation of a thermocouple. Take a look below for all of our PXI Simulation Solutions, we also offer some of these in PCI format as well . All of our PXI simulation cards are supplied with comprehensive software drivers for Windows® XP/Vista/7/8, Lab Windows / CVI and LabView. The Pickering IVI drivers also fully support National Instruments' Switch Executive.
-
Product
PXI Millivolt Thermocouple Simulator Module - 32 Channel
41-760-001
-
This series of PXI Thermocouple Simulator Modules is available in a choice of 32, 24, 16 or 8 channels—each channel providing a low-voltage output across two connector pins capable of providing ±20mV with 0.7µV resolution, ±50mV with 1.7µV resolution and ±100mV with 3.3µV resolution, covering most thermocouple types.
-
Product
PXI High Density Multiplexer, 1-Bank, 128-Channel, 1-Pole
40-610A-004
-
The 40-610A-004 is a 1-bank, 128-channel, 1-pole MUX and is part of our range of PXI high density reed-relay based multiplexer modules. The range includes a wide choice of switching configurations which are especially useful where a large number of small multiplexers are required. Typical applications include signal routing in ATE and data acquisition systems.
-
Product
PXI 3-Channel 10A Solid State SPST Switch
40-182-012
-
The 40-182-012 has 3 off high current SPST switches in one PXI slot and is part of our range of high power solid state switching solutions. Each SPST switch uses a fully isolated solid state relay which has been designed to offer fast operation under hot switching conditions and high inrush current with no operational life degradation. Each SPST switch can support 10A of continuous current and switch up to 200V signals. The switch can sustain inrush currents in excess of 50A. AC or DC signals can be switched since the switch is polarity insensitive.
-
Product
PXI Controller
-
The ADLINK PXI embedded controller, based on the Intel® processor family, is specifically suited for hybrid PXI-based testing systems, delivering a rugged and stable platform for a wide variety of testing and measurement applications. The PXI embedded controllers sport integrated CPU, HDD or SSD, and RAM, and provide ample interface flexibility, including one Gigabit Ethernet port for LAN connection and one for controlling LXI instruments, USB ports for peripheral devices and USB instrument control, and a Micro-D GPIB connector for GPIB instrument connection.
-
Product
PXI 12 Channel High Voltage Multiplexer
40-320-001
-
The 40-310/320 Range of High Voltage Switching Modules will hot switch up to 750V peak and cold switch up to 1000V peak in either general purpose relay (40-310) or multiplexer (40-320) configurations. These modules contain high-quality reed relays with switching ratings comfortably higher than the 40-310/320 specification. Applications for the 40-310/320 series modules include; circuit board isolation testing, relay testing, semiconductor breakdown monitoring and cable harness insulation testing.
-
Product
PXI Multi-Channel Function Generator Module, 24-Channel
41-625-002
-
The 41-625-002 (PXI) and 43-625-002 (PXIe) are function generator modules that provide 24 channels in a single PXI/PXIe slot. They can generate sine waves to 300 kHz with 5.76 mHz frequency resolution referenced to the 10 MHz PXI clock. The output voltage range is up to +/-25 V in a 16-bit resolution. It also support PXI trigger functions allowing events from other instruments to initiate waveform generation or sweeps.
-
Product
PXI 2 Amp MUX, Dual 4-Channel 4-Pole
40-635-107
-
The 40-635 2 Amp Multiplexer module is available in 9 standard configurations as well as 9 half density configurations, all using high quality electro-mechanical signal relays allowing each channel to switch current up to 2A and voltage up to 300VDC/250VAC.The module is suitable for signal routing in ATE and data acquisition systems. Connections are made via a front panel 78-way D-type connector.
-
Product
Single 32x2 1-Pole High-Density PXI Matrix Module
40-520-502
-
The 40-520 family of high-density PXI matrices is available in 22 different configurations with up to 256 crosspoints. The choice of six bus widths (x16, x12, x8, x6, x4 and x2) enables competitively priced solutions using Pickering Electronics instrumentation quality reed relays. These relays offer very long life with good low-level switching performance and excellent contact resistance stability. Typical applications include signal routing in ATE and data acquisition systems.
-
Product
PXIe-5673E, 6.6 GHz PXI Vector Signal Generator
781340-04
-
6.6 GHz PXI Vector Signal Generator—The PXIe‑5673E is a wide-bandwidth module that, when combined with the appropriate software, can generate a variety of signals. With the Modulation Toolkit for LabVIEW, it can generate different waveforms including AM, FM, CPM, ASK, FSK, MSK, PSK, QAM (4‑, 16‑, 64‑, and 256‑QAM), multitone signals, arbitrary waveforms, and many others. In addition, you can combine these vector signal generators with standard-specific software to generate signals for GPS, GSM/ EDGE/WCDMA, WLAN, WiMAX, DVB‑C/H/C, ISDB‑T, ZigBee, and others. With PXIe‑5673E stream‑from‑disk capabilities, you can generate continuous waveforms that are up to several terabytes in length.
-
Product
PXI RTD Simulator Module, 4 Channel, PT500
40-263-502
-
The 40-263-502 is a 4-channel PT500 RTD Simulator. The 40-263 range is a cost effective method of simulating PT100, PT500 or PT1000 RTDs. It supports 4, 8, 12, 16, 20 or 24 channels in one or two PXI slots. Also, channels are able to be set as short or open circuit to simulate faulty wiring to a sensor.
-
Product
PXI 2A Multiplexer, 158-Channel, 1-Pole
40-611A-001
-
The 40-611A-001 158-Channel, 1-Pole MUX is part of our range of Very High Density 2 Amp multiplexer modules. All configurations use high quality electro-mechanical signal relays allowing each channel to switch current up to 2A and voltage up to 300VDC/250VAC.
-
Product
PXI 15W Programmable Resistor Module
40-254-110
-
The 40-254-110 (PXI) and 42-254-110 (PXIe) are programmable resistor modules with 1 channel which can be set between 1Ω and 31Ω with 0.125Ω resolution The 40-254 range provides a simple solution for applications requiring up to 15W of power handling per channel.
-
Product
PXI 3A Power MUX BRIC, 2-Channel, 48-Pole
40-571-002
-
The 40-571 is a Power Multiplexer designed to simplify the connection of a common set of test equipment to one of a number of different devices for testing (simultaneous multiple channel selection is possible for most configurations, see switching specifications for restrictions). It is ideal for applications where the equipment needs to conduct the same test process on a series of similar devices one at a time. It is available in a variety of configurations that allow testing with differing number of devices to be tested and different connection widths to suit differing test equipment pin counts.
-
Product
PXI Functional Test System
U8989A
-
The TS-8989 PXI functional test system is an integrated, all in one switch, load and measurement system in a box for high voltage or current mechatronics functional test applications of up to 104 nodes and 40A current loads.
-
Product
PXI Single Transfer Switch 26.5GHz 50Ω SMA
40-782-531
-
The 40-780 Microwave switching module consists of one, two, three or four changeover switches capable of switching frequencies to 18GHz (optionally to 67GHz) in 50Ω or 2.5GHz in 75Ω. The 40-782 module consists of one or two microwave transfer switches. It has a characteristic impedance of 50Ω and is available in versions with maximum operating frequencies of 18GHz, 26.5GHz or 40GHz.
-
Product
PXI 38 Channel 2 Amp Multiplexer Card
40-656-001
-
A 38-channel multiplexer, 2-pole switching, suitable for switching signals to 2Amp, 220VDC/125VAC. It offers the highest switching density in its class for medium power/ voltage signals. Specifically designed for switching POTS, ISDN or xDSL telephony signals. Bandwidth for most configurations is typically >25MHz. It is paired with a very similar module, 40-655-001, a multi-banked multiplexer.
-
Product
PXI Precision Resistor Module 4-Channel, 2 to 52.4k
40-297-133
-
This 4-channel PXI Precision Resistor Module provides a simple solution for applications requiring accurate simulation of resistive sensors. The 40-297 series is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems. It is particularly well suited to applications such as the testing of engine controllers where resistive sensors provide information on parameters such as temperature.
-
Product
3U OpenVPX 2-Slot Backplane With 1 VPX Power And Ground Plus 1 VITA 62 Power Supply Slot
101VPX302-xxxx
-
This 3U Open VPX backplane offers one VITA 46 Power and Ground slot and one VITA 62 power supply slot to support the development and deployment of systems requiring a VITA 62 power supply. The rear power studs can be used to connect to an adjacent backplane to feed it power.
-
Product
PXIe-6674T, OCXO PXI Synchronization Module
781037-01
-
PXIe, OCXO PXI Synchronization Module—The PXIe‑6674T generates and routes clocks and triggers between devices in a PXI Express chassis as well as to other PXI and PXI Express chassis or third-party instrumentation. The PXIe‑6674T unlocks the advanced low-voltage differential signaling (LVDS) trigger signals PXIe‑DStarA, PXIe‑DStarB, and PXIe‑DStarC, on PXI Express while fully supporting the PXI trigger lines. The PXIe‑6674T can generate two types of clock signals: a highly stable 10 MHz clock based on an onboard precision oven-controlled crystal oscillator (OCXO) reference and a second clock from the direct digital synthesis (DDS) clock generation circuit.
-
Product
PXI Precision Resistor Module 9-Channel, 2 to 13.6k
40-297-031
-
This 9-channel PXI Precision Resistor Module provides a simple solution for applications requiring accurate simulation of resistive sensors. The 40-297 series is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems. It is particularly well suited to applications such as the testing of engine controllers where resistive sensors provide information on parameters such as temperature.
-
Product
High-Power PXI Multiplexer Switch Modules
-
Our High-Power PXI Multiplexer Switch Modules are based on electro-mechanical and solid state relays capable of switching currents of up to 40 Amps. Each module supports one or more multiplexer channels between one input/output terminal and a selection of output/input terminals. To reduce through path resistance, most of these multiplexers do not include isolation relays.
-
Product
PXI 5A Power MUX, 4-Bank, 11-Channel
40-651-003
-
This range of high density power multiplexer modules is suitable for switching inductive/capacitive loads up to 5A at 250VAC. It is available in the following 1-pole multiplexer formats: 1-bank 48-channel. 2-bank 24-channel. 4-bank 11-channel. 8-bank 5-channel.Connections are made via a front panel 50-way male D-type connector. Power multiplexer modules are intended for switching heavy AC or DC loads or for slaving up to large external relays, contactors and solenoids.
