Solid State Relays
-
product
Low capacitance SIL reed relays
Series 103
Low Capacitance SIL relays. Requires a board area of 0.25 x 1.0 inches (6.4mm x 25.4mm). Form A with one fifth the usual switch to coil capacitance
-
-
product
Frequency Sensing Relay
This relay is a frequency monitoring relay with four stages of adjustable frequency pick up & drop out points. Each frequency set point can be set for under or over frequency operation & has an independent time delay driving an output relay. An undervoltage lockout is used to disable the four frequency outputs when the voltage falls below a preset level. Each of the four setting stages has a rate of change of frequency (ROCOF) element with an independent time delay.
-
product
High DC Breaking Capacity (12A) Relays
D-BYX5 Series
Heavy duty relays for demanding applications. Integrated magnetic arc blow-out function and contact gap 4mm for higher DC breaking capacity.
-
product
Relay I/O Modules
XTA Series
These modules are intended for use with BusWorks XT Series discrete I/O or other digital output modules for the purpose of driving high energy loads.
-
product
Diagnostic Relay Buddy 12/24 Test Kit
193
Relay Buddy 12/24 Pro Test Kit tests five different relays. Relay Buddy is a quick go / no-go tester for the most common automotive relays and this new version tests both 12 and 24 volt relays. . If the relay fails the test, 3 different trouble codes will advise you of the possible causes for the failed relay. The red LED will flash once, twice or three times to indicate the problem. Trouble code definitions are printed on the back of the tester for your convenience.
-
product
24.50 (622.30) 24" Solid Panel
P-2424
Special grade .125” sheet aluminum (5052-H32 EPS). Each side, edge and corner is carefully de-burred and chamfered to provide a flawless finish, resulting in a superior quality panel. , A multi-step painting process is used to paint the panel - the finish is textured unless otherwise specified.
-
product
Protective Relay Test Set
POM2-6143
POM2 series protective relay test equipment is the best modular designed relay tester with local control system. There are 2 models, the POM2-6143 and POM2-3243, the POM2-6143 with 6×15A and 4×300V.
-
product
8-CH Relay Outputs & 8-CH Isolated DI PCI Cards
PCI-7250/7251
ADLINK's PCI-7250/7251 provide 4-CH SPDT (Form C) & 4-CH SPST (Form A) relay outputs and 8-CH isolated digital inputs. The status of each relay output is represented by an onboard LED. When the relay is in SET condition, its corresponding LED will turn ON, and on the contrary, it is OFF. All digital input channels are nonpolarity, optically isolated, and may be set to use RC filter or not. The devices are suitable for collecting digital inputs in noisy environments. The PCI-7251 is an 8-CH relay outputs and 8-CH isolated DI extension card of the PCI-7250. All the I/O functions of PCI-7251 are the same as those of the PCI-7250. The PCI-7251 has to be connected with PCI-7250 and the bus interface is controlled by the PCI-7250. Up to three PCI-7251 cards can be connected to one PCI-7250, therefore, expanding the PCI-7250's DIO from 8 DIO to maximum 32 DIO.
-
product
SIMRC - 16 x Uncommitted Reed Relay, SPDT
1010-R-16-1-5/3D
Our small format embedded switching (SIM relay) cards offer a choice of switching configurations using low cost industry standard SIM connectors. They free the designer from the detail of routing complex switching circuits, you may select from a wide range of cards using the built in RS-232 and I2C interfaces. These low-cost embedded switching cards are intended to be mounted on to a simple motherboard. They may be used to construct very high density switching networks. SIM based switching cards also allow for very simple in-field maintenance.
-
product
19" Solid Fixed Storage Shelf, 20"D
SS-1920
Sturdy 19" shelf formed of one piece of 16 ga. CRS bolts to panel mounting rails. Supports heavy chassis or power supplies or provides storage for tools, test leads, chart paper, etc.
-
product
Solid State Digital Matrix Switching Systems
DX Series
Cytec's DX Series Switching Systems are based on solid state switch fabric. All systems are non-blocking (any input to any output) and full fan-out (any input to any or all outputs)
-
product
Solid State
4701 Series
The 4701 Model is a Non-blocking Full Fan-Out (any input connected to any output simultaneously) coaxial switching system operating from 1 GHz to 18 GHz. The system is configured with maximum (12) N-type inputs and (12) SMA-type outputs. All inputs are outfitted with high linearity amplifiers in order to compensate for system insertion loss.
-
product
Steady State Solar Simulator
Our steady state solar simulators enable you to test and develop solar thermal collectors independent of weather and season, faster, more efficiently and more comprehensively than ever before. Both simulators are turnkey products, delivered 100 % ready to go!
-
product
SWB-2833, 4x71, 2 A, Electromechanical Relay Matrix Module for SwitchBlock
781421-33
4x71, 2 A, Electromechanical Relay Matrix Module for SwitchBlock - The SWB‑2833 is an electromechanical relay matrix card for SwitchBlock systems. Designed for high power, it can operate as an individual relay card or expand in a single carrier or single PXI chassis. You can connect any input to any output, individually or in combination. You can use matrix switches to route signals from oscilloscopes, DMMs, arbitrary waveform generators, and power supplies to various test points on a unit under test (UUT). The primary benefit of matrix switches is simplified wiring—the overall test system can easily and dynamically change the internal connection path without any external manual intervention.
-
product
PXI 25 x DPST Electromechanical Relays
40-146-002
The 40-145/46/48 range of high density switching modules are available in Normally Open (SPST & DPST) and changeover (SPDT) configurations. Connections are made via a front panel 200 pin female connector. General purpose relays are suitable for the construction of small switching networks, I/O port switching, for slave switching larger relays or for operating external devices (e.g. lamps, solenoids etc.).
-
product
Buchholz Relay Test Benches
HAOMAI Electric Test Equipment Co., Ltd.
Buchholz relays are used to protect transformers, and these test benches perform necessary quality and performance checks.
-
product
PXI 8 Slot BRIC Solid State 160x8 1-Pole (5 sub-cards)
40-563A-121-160X8
This version of our BRIC is part of a range of high-density PXI matrix modules. These modules are available in 2, 4 or 8-slot PXI sizes to suit all high performance PXI matrix requirements and are constructed using solid-state switches. With this high level of switching density, these PXI matrix modules allow a complete Functional ATE system to be housed in a single 3U PXI chassis. These BRIC matrix modules allow the use of lower cost 8 or 14-slot PXI chassis.
-
product
C Series Relay Output Module
The C Series Relay Output Module enables you to switch up to eight signals at 60 V maximum DC switching voltage and up to 250 V of maximum AC switching current. For quick reference, every channel features an LED to indicate the state of that channel. The C Series Relay Output Module allows for direct connection to a wide array of industrial devices such as motors, actuators, and DC devices.The C Series Relay Output Module includes the NI-DAQmx driver and configuration utility that simplify configuration and measurements. NI-DAQmx supports NI programming environments as well as Python, ANSI C, C#.NET, and MathWorks MATLAB® software.
-
product
Astronomic Time Relays
Time Relays are smart time relays which are capable of automatically calculation of the sunrise and sunset times and have internal real time clocks. They are designed to control the devices which are connected to output contacts on user defined times, sunrise and sunset times.
-
product
Miniature Instantaneous Relays
CU-D Series
Heavy duty miniature power relays for demanding applications, switching of AC&DC voltages, resistive and/or inductive loads. Equippedwith weld no transfer contacts.
-
product
Low Current Switching Relay
D-E Series
Heavy duty relays for demanding applications, suitable for low current switching, equipped with gold plated contacts.
-
product
Protection Relay Testing
Haomai Electric Power Automation Co.,Ltd.
1)Embedded industrial PC with 9.7" TFT LCD screen 2)Both online and offline test available 3)Can test both universal and IEC 61850 protection relay 4)6-phase current + 6-phase voltage output 5)Provide various type of messages which conforms to IEC 61850-9-1/9-2,GOOSE, IEC 60044-7/8 FT3 6)Able to test MU and optical digital signal 7)Built-in GPS module
-
product
High Voltage Dry Reed Relays
Series 60 & 65
High voltage relays - chassis mounted, up to 15kV. Tungsten switches with power rating of 50 Watts maximum. Series 60 has solder terminals and nylon chassis mounting studs
-
product
GHz Microwave Relays
CXM DC to 40
Cytec can offer hundreds of different microwave relays from multiple vendors. Standard relays are DC to 18 GHz with SMA connectors but options include:
-
product
PXI SPDT Switch: 26-ch, 2A, Armature Relay
M9130A
The M9130A is a general purpose switch with 26 independent, single-pole, double-throw (Form C) switches in a single PXI module. This module can be used to cycle power to products under test, control indicator and status lights or actuate external power relays and solenoids. The armature relays can handle up to 60W power. When needed, these relays can handle up to 6A pulsed carry current. Choose from the durable connector block or standard cable connections.
-
product
PXI 8 x SPDT Power Relay Module, 5A
40-155-001
40-150/151 modules have 8xDPST or 12xDPST power relays, suitable for switching inductive/capacitive loads up to 5A at 250VAC. 40-155/156 modules have 8xSPDT or 16xSPDT power relays and 40-157 is configured as 8xDPDT.
-
product
Three Phase Relay Testing
Our comprehensive and intuitive relay software speeds up testing times with a vast library of pre-defined test regimes or manual operation.
-
product
USB Programmable SPDT and SP4T Solid State RF and Microwave Switches
LSW Series
The Lab Brick LSW Series RF and Microwave Switch product family offers reliable, high isolation and low cost solid state switch products in both single pole double throw and single pole four throw configurations. These units require connection to a USB port for control and power. No additional DC supply voltage is required. Lab Brick RF and Microwave Switches are easily controlled and programmed directly from the included GUI and through the external control inputs. Lab Brick Switch API DLL and LabVIEW compatible drivers are also available for custom programming applications.
-
product
Mechanical Power Relays (2A Or More)
Panasonic Industrial Devices Sales Company of America
Panasonic's Mechanical Relays with greater than 2A nominal switching capacity and comes in polarized and non-polarized types. Panasonic has a wide range of switching capacities up to 120A AC and 300A DC, with various contact arrangements and sizes. Panasonic also has Power Relays with low coil holding capability for lower power consumption.
