Print Circuit Board
-
Product
PCIe Carrier Board for SOM3
Solar Express 215 (SE215)
-
Sundance Multiprocessor Technology Ltd.
SE215 is a development board for Sundance SOM3 . It is a PCIe X1 Gen2 carrier card with one site for an SOM3. It offers USB JTAG and UART, through a micro USB connector, Display port and comes with a version of Display port IP core for SOM3 from Bitec DSP. The card provides Power GOOD and user LEDs for rapid debugging.
-
Product
CT Tester, Meter Tester, Circuit Analyzer
GOLD MINER IV
-
Gold Miner is the first device of its type to test the electricity meter using exact, simultaneous measurements made on all primary and all secondary phases of the circuit. Perform in-service meter testing with a combined 3-phase load, or a single-phase load. Gold Miner not only displays the Meter’s accuracy, but also the overall, true accuracy resulting from the CTs + Meter combination for your entire measurement circuit.
-
Product
Compact PCI Connector Board
cPCI-J2-SCSI
-
Ribbon cable is used between the rear IO and SCSI connector. The lengths are reasonably well matched. The cable is short. The design is intended for lower speed IO - 10 MHz and below. Above 10 Mhz there may be some attenuation.
-
Product
Test Extension Boards
XJIO
-
The XJIO boards are expansion units that enable you to improve the test coverage for a Unit Under Test (UUT) by verifying the signals right through to the external connections. They will integrate with your XJTAG test system to provide access to otherwise inaccessible areas of your circuit. With a range of digital and analogue I/O pins on the board, you can improve fault isolation, verify power rail levels, and dispense with costly custom test jigs - even for non-JTAG boards.
-
Product
Pkt2-PCIe and Pkt2-AMC Boards
-
Provide front-end intelligent processing for DPI, IPsec and GTP acceleration, delivering a high-performance, secure, carrier-grade, packet processing for LTE, 3G and IMS networks.
-
Product
LOADED BOARD TEST PROBES
SERIES-70
-
ElectricalMAXIMUM CURRENT: 5 amps continuousat working travel, non-inductiveRESISTANCE: At 35mA test current70 18 mOhms mean73 60 mOhms mean74 40 mOhms meanMaterials and FinishesPLUNGER: Heat treated beryllium copperor steel hardened to 55-60RC70 24Kt gold plated over nickel73 24Kt gold plated over nickel74 Rhodium plated over nickelBARREL: Nickel silver70 24Kt gold plated ID and OD over nickel73 No Finish74 24Kt gold plated ID and OD over nickel
-
Product
PC/104 OneBank I/O Board
EMC²-KU40
-
Sundance Multiprocessor Technology Ltd.
The PCIe/104 OneBank™ design enables the EMC²-KU40 to be added to robust and rugged installations for various commercial, medial, industrial and military uses and to enable more versatility the EMC²-KU40 also incorporates a VITA57.1 FMC™ LPC connector opening up an range of extra possibilities and expansion options.
-
Product
Load Board
cPCI 6U
Load Module
Load boards are essential in keeping any system in top running shape. As a full-system provider, Hartmann strives to not only provide the systems you need, but the supporting hardware as well.
-
Product
6-48V Nixie Digital Display Circuit Tester
1674B
-
Peaceful Thriving Enterprise Co Ltd
Check on 6, 12, 24 and 48V systems.
-
Product
Pulse Generation Measurement Board
MS 1806
-
*TTL Pulse measurement channels (Timers / Counters) 18 Channels*TTL Pulse Generation - 12 Channels*The Pulse Generation Frequency from 10Hz to 40MHz*The no. of pulses controlled from 1 to 255 pulses*All Channels are compatible with 5V TTL / CMOS*All the pulse input and the output signals driven through Pin Driver*Standard ISA Bus Interface*Driver interface for Windows2000/XP/VISTA and LINUX OS
-
Product
Visual Control of Printing Complex
Polygraph
-
The complex of visual control of printing (KVKP) is designed to visualize the image of the print output on the canvas during the operation of the roll printing machine and can be used instead of a stroboscope, providing more convenient observation of the printing process.
-
Product
12 Channel External Timing Board
0000-002
-
Timing Channels: 12 x 16 bit channels. Each can be programmed for event counting, elapsed time indication, rate generation, and programmable one-shot applications
-
Product
Circuit Breaker Test Equipment
-
DV Power has released a new generation of circuit breaker test equipment for condition assessment of medium and high voltage circuit breakers.Field-portable instruments with standalone or PC controlled functionality, allow performing various tests during circuit breaker manufacturing, commissioning and maintenance stages.Applications supported by the DV Power test equipment include measurements of:Contact resistanceDRM (dynamic resistance measurement)Coil resistance and coil current (IEC 62271-100)Mechanism charging time (IEC 62271-100)Minimum trip voltage (IEC 56, ANSI C37.09)Undervoltage release (IEC 60694)The timing of a circuit breaker’s main, auxiliary and pre-insertion contactsSynchronization between the contactsMotion and velocity“First trip” testThe essential part of a circuit breaker condition assessment is the ability to compare the latest test results with the previous testing. Accordingly, our instruments store measured values and compare them to a manufacturer’s limits. Also, a fingerprint obtained in this way can be used at a later stage as a reference during subsequent measurements. In order to obtain an accurate comparison, the tests need to be performed using identical test parameters. Consequently, any deviation and change in the test results may indicate the circuit breaker condition deterioration. Even more, to overcome this issue, DV-Win enables test plans and graph overlay features.Finally, as a final result of a circuit breaker maintenance process, the DV-Win provides analytical tools and customized report creations.
-
Product
Digital I/O Board
3512
Digital I/O Module
The 3512 is an eight channel non-isolated digital I/O board with +5V tolerant 74LCX14 inputs with hysteresis and +3.3V CMOS 74LVTH125 driven outputs. Each I/O line features a series 10 ohm damping and protection resistor and a 4.7K pull up resistor to +3.3V. On power up the outputs are tri-stated, and can then be enabled on a bit by bit basis. Output high drive is 32mA @ 2.0V minimum. Output low drive is 32mA @ 0.8V maximum.
-
Product
DAQ Terminal Board
-
* Provides screw terminal connections for the Analog, Digital, Relay Driver and Thermocouple signals.* Mates with the 62-pin connector on the 2307 boards and the 2367 Minibox™.
-
Product
Three Phase Meter Test Board
MTB-3050
-
TESCO’s MTB-3050 is a Three Phase Meter Test Board with every laboratory feature you could want along with metrology and software suitable for your production meter testing needs.
-
Product
Dynamic Test Board Vehicle Simulator
DTB
-
The Dynamic Test Board vehicle simulator range enhances functional testing by allowing greater test depth before the prototyping stage.
-
Product
Serial To Digital Interface Boards
-
*ICS's Serial to Digital Interface boards provide the user with digital IO signals that can be user configured to match virtually any application. Both boards are available with high power relay drivers and with optional firmware designed to simplify switching applications.*All boards are designed for mounting inside a chassis.
-
Product
Hall Sensor Board with I2C Interface
050-279
-
Version: +5V/90A +3,3V/25A +12V/60A +12V/60A The Hall-Sensor Board is the right accessory for your system in combination with the Elma SysMon. It's possible to measure up to 4 currents and to monitor them with the Elma SysMon 3 Gen.
-
Product
PCIe I/O & Comm Board
79C3
Multifunction I/O
NAI’s 79C3 is a PCIe Multifunction I/O and Communication Board with three independent function module slots that can be configured with a variety of I/O and communication functions. Additional enhancements include FIFO data buffering for select modules. Using multiple DSPs, the enhanced motherboard enables higher processing power and dedicated pre-processing control for each module.
-
Product
PCI To CPCI Or PXI Extender Board
MS 1720
-
PCI to CPCI Extender card is used for extending the standard desktop PCI bus to compatible CPCI bus. This will help to test all the CPCI and PXI cards without having a CPCI or PXI backplane. This card is very low cost board and very use to interface with standard board. This board also facilitates to debug the CPCI and PXI boards.
-
Product
Burn-in Board Continuity Tester
CT-1
-
Burn-in Board Coninuity Tester. Verifies burn-in board continuity and component tolerances. 768 I/O channels, can be forced to the constant current source or grounded independently. Highly accurate measurement of resistance, voltage, and capacitance using a pair of precision instrumentation amplifiers.
-
Product
Multi-layer Short Circuit Locator
Toneohm 950
-
Polar Toneohms are ideal tools for the electronics production environment. Able to locate shorts quickly and accurately on both bare and loaded PCBs, they provide a very cost-effective means of minimizing repair and rework of faulty PCBs that have been identified by pass/fail testing on an ATE system.
-
Product
Three Phase Meter Qualification Board
MQB3
-
Apply true three phase voltage and current to electric meters, enabling them to be tested under all possible conditions that may be encountered in the field with TESCO’s Three Phase Meter Qualification Board (MQB3).
-
Product
Precision Analog Anti-Alias Low-Pass Filter Board
GSAF-10
-
The GSAF-10 Gold Series are analog low-pass filter boards that offer the performance required to maintain the maximum accuracy of high-precision 16- and 18-bit A/D converters.
-
Product
3U PXI Express Board
SMT709
-
Sundance Multiprocessor Technology Ltd.
The SMT700 is one of the first of a new range of Sundance cards that includes a direct connection to SLB (Sundance Local Bus) compatible mezzanine card, without the need for a Sundance TIM. This enables a variety of cards to be added to a system, for example extra Ethernet ports, video in/out, High speed ADC / DAC etc. Data from these extra cards (along with data from the SMT700’s own inputs – up to 1Gb/s Ethernet, 2.5Gb/s optical links, and RSL links) can be processed via the Virtex 5, or by another linked card or module.
-
Product
PCIe/104 OneBank I/O Board
EMC²-7K70
-
Sundance Multiprocessor Technology Ltd.
The PCIe/104 OneBank™ design enables the EMC²-7K70T to be added to robust and rugged installations for various commercial, medial, industrial and military uses and to enable more versatility the EMC²-7K70 also incorporates a VITA57.1 FMC™ LPC connector opening up an range of extra possibilities and expansion options.
-
Product
Airborne Video Delay Board
MS 2006
-
- Spartan FPGA based Design- Customized design for delaying & switching video inputs to RF section- Interface with EW Signal Processor Unit- Two channel video inputs and control- Video Signal Delay from 1ns to 1ms- Over duty Indications- Inhibit Control- Discrete Interface
-
Product
Isolated Programmable Multifunction Counter Board
APCI-1710-5V-I
-
Wide application possibilities through free combination4 modules with numerous functions quickly and easily programmableEach of the 4 modules is programmed with a function. The 4 modules can either be programmed with the same function or freely be combined with 4 different functions.
-
