Serial
a bus that can be used with almost any device transmitting a single stream of data.
See Also: Bus, Parallel, I2C, LIN, Can bus, ExpressCard, Fieldbus, FireWire, RS-232, RS-485, PCI Express, Serial ATA, Serial Peripheral Interface, SMBus, Serial Analyzers, Serial Digital Interfaces, Serial Communications, Serial Data
-
Product
Ethernet/AFDX/BroadR-Reach PXI Fault Insertion Switch - 4 Channel
40-201-004
Fault Insertion Unit
This high bandwidth differential fault insertion module is designed to simulate common faults on high speed two wire communication interfaces such as Ethernet. This module supports 4 or 8-channels of two wire serial connections and can be used for simulating faults on Ethernet, AFDX, BroadR-Reach, 100BaseT and 1000BaseT interfaces. Any wire can be set to an open circuit, shorts can be applied across the wire pair, or to the adjacent pair. Fault connections can be made to one of four external signals via two fault buses, typically simulating connections to a supply voltage or ground. Each fault bus is capable of carrying 2A allowing multiple channels to be connected to the same fault condition. Additionally, each fault bus features a changeover relay to allow the user to connect alternative fault conditions to the fault buses.
-
Product
1-Ch. 6.4 GHz or 2-Ch. 3.2 GHz A/D, 2-Ch 6.4 GHz D/A Kintex UltraScale - 3U VPX
Model 54141A
-
- Jade Xilinx Kintex UltraScale FPGA Products and Navigator Design Suite Software Video- Jade Xilinx Kintex UltraScale FPGA Family Brochure- Exceptional dynamic range and analog signal integrity- Xilinx® Kintex® UltraScale™ FPGAs- Compatible with several VITA standards including: VITA 66.5 and VITA 67.3C- Supports VITA 49.2 VITA Radio Transport standard- One-channel mode with 6.4 GHz, 12-bit A/D- Two-channel mode with 3.2 GHz, 12-bit A/Ds- Programmable DDCs (Digital Downconverters)- Two 6.4 GHz, 14-bit D/As- Programmable DUCs (Digital Upconverters)- 5 GB of DDR4 SDRAM- uSync clock/sync bus for multimodule synchronization- PCI Express (Gen. 1, 2 & 3) interface up to x8- Optional LVDS and gigabit serial connections to the FPGA for custom I/O- Ruggedized and conduction-cooled versions available- Navigator® BSP for software development- Navigator® FDK for custom IP development- SPARK® fully-integrated development system
-
Product
PCI/PCIe-Based Serial Communications Cards
PCI-C588/PCI-C584/PCIe-C588
-
- IRQ & IO address automatically assigned by BIOS- Supports up to 2 cards per system, jumper-less, easy to configure- Isolated RS-422/RS-485 interface (C422/C485, C518/C514)- PCI Rev 2.1 Plug-and-play- PCI Express® x1 compliant (PCIe-C588)
-
Product
Pulse Pattern Generators
PPG
-
The Pulse Pattern Generator family (PPG), also knows as Serial Data Pattern Generator (SPG), is designed to generate a stream of binary information.
-
Product
10 Gb/s SFP/SFP+ Evaluation Board
EV-SFP-171
-
The purpose of this SFP+ evaluation board is to provide the designer with a convenient means for evaluating SFP+ fiber optic transceiver such as 10 Gb/s(up to 16 Gb/s) SFP/SFP+ transceiver compliant with ANSI Fibre Channel FC‐PI‐5 for high speed electrical and optical specifications. This board provides SMA connectors for high speed TX and RX signals. The low speed control signals such as Tx_Fault, Rx_LOS and Rate_Selects can be controlled by using on board switches and test points. A connector for 2 wire serial interface to the module is also provided.
-
Product
cRIO-9035, 1.33 GHz Dual-Core CPU, 1 GB DRAM, 4 GB Storage, and Kintex-7 70T FPGA, 8-Slot CompactRIO Controller
784774-01
Embedded Controller
1.33 GHz Dual-Core CPU, 1 GB DRAM, 4 GB Storage, and Kintex-7 70T FPGA, 8-Slot CompactRIO Controller - The cRIO-9035 is a rugged, fanless, embedded controller that you can use for advanced control and monitoring applications. This software-designed controller features an FPGA, a real-time processor running the NI Linux Real-Time OS, and embedded user interface capability. You also can use the Mini DisplayPort to add a local human machine interface (HMI) for application development. Additionally, the cRIO-9035 features an SDHC slot and a variety of connectivity ports, including two tri-speed RJ-45 Gigabit Ethernet, two USB host, one USB device, and two RS-232 serial. The registered trademark Linux® is used pursuant to a sublicense from LMI, the exclusive licensee of Linus Torvalds, owner of the mark on a worldwide basis.
-
Product
Carousel Autosamplers
-
The carousel platform is designed to be sturdy, reliable, and easy to use. The rotating sample tray minimizes space requirements, making it easy to fit into an existing housing. It holds up to 96 samples when fully loaded and contains a microprocessor that allows sequential or random sampling. The autosampler is typically interfaced to and controlled by the host instrument computer using a serial, USB, or IEEE-488 parallel communications cable.
-
Product
Camera Link Frame grabber
Cyton-CXP
-
CoaXPress (CXP) is a simple, yet powerful, standard for moving high speed serial data from a camera to a frame grabber. Video is captured at speeds of up to 6.25 Gigabits/Second (Gb/S). Simultaneously, control commands and triggers can be sent to the camera 20 Mb/S (with a trigger accuracy of +/- 2 nanoseconds). Up to 13 W of power can also supplied to the camera.
-
Product
Temperature Logger with Integral sensor and Probe
TV-4510
-
Dual channel temperature recorder LCD display of current readings 30,000 readings capacity High accuracy and reading resolution Fast data offload Splashproof case Low battery monitor and battery low indicator Programmable alarms Optional audible alarm box USB and serial download cables
-
Product
DSP Based Serial Communication Board
CPCI-ISC8
Communications Module
The CPCI-ISC8 is an intelligent DSP based serial communication board. This 3U board is based on the CPCIIPC product and has been modified to remove the IPinterface and to support additional I/O features. The CPCIISC8 provides mechanical support and the electrical interfaces for an I/O mezzanine board. Multiple CPCI-ISC8 boards may be installed in a single system.
-
Product
8 CANBus Channels, CAN 2.0 A/B Protocol or J1939 Protocol
CB3
-
The serial bus system with real-time capabilities is the subject of the ISO 11898 International Standard and covers the lowest two layers of the ISO/OSI Reference Model. Our CANBus modules provide independent, isolated channels of CAN serial data bus links, conforming to the ISO 11898 International Standard. All CAN nodes are able to transmit data and several CAN nodes can request the bus simultaneously.
-
Product
Mixed Signal Oscilloscope
MSOX3024A
Oscilloscope
200 MHz4 analog plus 16 digital channels Easily view your signals on the 8.5-inch WVGA display Capture more data with up to 4 Mpts memory See more signal detail with 1,000,000 wfms/s update rate Expand your measurement capabilities with full upgradability: Add bandwidth, memory, 20 MHz arbitrary waveform generator, 3-digit voltmeter, serial trigger and analysis, segmented memory & mask testing at any time
-
Product
Multibus Ethernet Card
MS 1750
-
- Processor: LPC3250 processor with ARM 9 core running at 266 MHz- SDRAM Memory: DDR2 256 MB (scalable to 512 MB)- Flash Memory: NAND flash 512 MB- Display & Graphics: Programmable color LCD controller supports up to a TFT interface- Touch screen: Integrated touch screen controller- Network Support: 10/100 Base-T Ethernet PHY- PC Interface: One USB 2.0 high-speed On-the-Go interface- Multibus Interface- Serial Interfaces: Up to four external UARTs- CAN 2.0B controller- Three I2C ports- Three SPI ports- GPIO: Programmable I/O depending on peripheral requirements
-
Product
Fifo Serial Analyzer Breakout Box
FLLBOB
-
FLL BreakOut Box FLLBOB is a breakout box specially designed to be used with the FLL and FSA serial analyzers. With FLLBOB it is easy to connect the PC to the serial line without having to make dedicated cables.
-
Product
3U CompactPCI Serial 2-Port Serial Card
cPCI-A3COM
cPCI Card
- Follow PICMG® CompactPCI® Serial design guide- CompactPCI® Serial, 3U 4HP- 2x DB9 COM ports in front panel- Operating temperature: -40°C to +85°C- Designed to meet EN50155 standards
-
Product
OnyxFX FlexorSet 4-Ch 16-bit: 500 MHz A/D & 2 GHz D/A - 3U VPX
Model 5973-324
-
- Supports Xilinx Virtex-7 VXT FPGA- GateXpress supports dynamic FPGA reconfiguration across PCIe- Four Channel 500 MHz 16-bit A/Ds- Four Channel 2 GHz 16-bit D/As- 4 GB of DDR3 SDRAM- Sample clock synchronization to an external system reference- PCI Express (Gen. 1, 2 and 3) interface up to x8- User-configurable gigabit serial interface- Optional optical Interface for backplane gigabit serial interboard communication- Optional LVDS connections to the Virtex-7 FPGA for custom I/O- Compatible with several VITA standards including: VITA-46, VITA-48 AND VITA-66.4 and VITA-65 (OpenVPX™ System Specification)- Ruggedized and conduction-cooled versions available- Xilinx Sublicense FAQs - Pentek Sublicensing Agreement for Xilinx JESD204 IP Cores
-
Product
Cavium CN66xx Packet Processor AMC
AMC732
-
The AMC732 is a 10-Gigabit Ethernet (10GbE) AdvancedMC™ (AMC) module which includes an on-board multi-core packet processor based on Cavium CN66XX CPU. VadaTech offers this product in a mid size (full size optional) form factor with the AMC.1, AMC.2 and AMC.4 specification. The AMC732 is based around the Cavium OCTEON CN66xx processor which has been specifically designed to intelligently process Ethernet packets at line rate. The processor can be loaded via the PCIe/SRIO interface or via an optional flash memory. The number of processor cores, speed grade, and amount of DDR3 memory is customizable based on customer needs.The module has an RTC on board and 2GB of HFA for pattern matching for deep packet inspection, etc. The SDK for the processor as well as additional software stacks are available from Cavium or third party. The AMC732 has Serial Over LAN (SOL) with a true hardware Random Number Generator.
-
Product
OnyxFX FlexorSet 4-Ch. 250 MHz A/D, 2-Ch. 800 MHz D/A - 3U VPX
Model 5973-312
-
- Supports Xilinx Virtex-7 VXT FPGAs- GateXpress supports dynamic FPGA reconfiguration across PCIe- Four 250 MHz 16-bit A/Ds- One digital upconverter- Two 800 MHz 16-bit D/As- 4 GB of DDR3 SDRAM- Sample clock synchronization to an external system reference- PCI Express (Gen. 1, 2 and 3) interface up to x8- User-configurable gigabit serial interface- Optional optical Interface for backplane gigabit serial interboard communication- Optional LVDS connections to the Virtex-7 FPGA for custom I/O- Compatible with several VITA standards including: VITA-46, VITA-48 AND VITA-66.4 and VITA-65 (OpenVPX™ System Specification)- Ruggedized and conduction-cooled versions available- Also available as Model 7070-312- See comparable JadeFX Xilinx Kintex UltraScale FPGA Family:Model 5983 JadeFX Kintex UltraScale Processor and FMC Carrier - 3U VPX
-
Product
Serial Digital Interface
Model 2363
-
* Provides 48 high-power TTL I/O lines that can sink 48 mA or source 24 mA. * Easily interfaces to TTL or CMOS signals and contact closures. * User can configure the data bytes as inputs or outputs.* Transfer data as bits, bytes or data strings.* RS-232 and RS-485 Serial IO.* 1 U high rack mount kit mounts one or two 2363s* Includes US 115 VAC Power Adapter
-
Product
rSSD SATA 3
-
RunCore Innovation Technology Co. Ltd.
RunCore rSSD RC0 series solid state drive compliant with Serial ATA Revision 2.6 and 3.1 specification and compatible with 3.0Gbps and 1.5Gbps interface rate. The rSSD family extends’s portfolio of high-performance, fully-integrated embedded solid-state drives.
-
Product
Ethernet
-
Ethernet, arguably the most common communication protocol on the planet, continues to spread into new markets and incorporates new protocols; it presents today’s Ethernet engineers with host of new test and validation challenges. Specifically, the increasing adoption of lossless Ethernet standards like FCoE, RoCE, and NVMf and increases in the line-rates of Ethernet from 10GbE and soon to 100Gb/s to name a few.These new physical and logical communications standards have exposed legacy test tools as outdated and incomplete for Ethernet product developers and the ecosystem. Teledyne LeCroy is addressing these needs by leveraging our extensive experience in high-speed serial data analysis tools currently used by many of the same companies developing products for NAS, SAN, LAN, and other high-speed protocol environments.The SierraNet Family of Ethernet test platforms provides best in class traffic capture, analysis, and manipulation for testing physical link characteristics and application operations. SierraNet is designed for addressing today’s high-speed storage and communications network problems and compliments other tools offering industry leading visibility and utility.
-
Product
Test & Programming Software
ScanExpress
-
The ScanExpress Family of boundary-scan software offers a fully integrated development environment that includes boundary-scan and at-speed functional test program generation, test program execution with advanced pin level diagnostics, interactive boundary-scan debugging, and in-System Programming (ISP) of devices such as Flash memory, serial EEPROMs, CPLDd, and FPGAs.
-
Product
Industrial GSM MODEM
QSM-26
-
Infinite Industrial Informatics Lt
QSM-26 is a DIN rail mount GSM/GPRS MODEM. The unit has a built in Quad Band (850/900/1800/1900MHz) Sierra Wireless Q2687 modem, 2 digital inputs, 2 power relay outputs and a serial RS-232 port. Special AT commands are implemented for TCP/IP based communications.
-
Product
Light / Lux Meter, Calibrated w/Data, 50000 lx, 100 lx, 4 %, 185 mm, 78 mm, 38 mm
72-7250 CAL D
-
The 72-7250 CAL D from Tenma is a digital light meter with RS232 capability. It has custom one-chip microprocessor LSI circuit which ensures high accuracy. The meter features 13mm (0.5”) super large LCD display with contrast adjustment for best viewing angle, data hold and auto power off. It records maximum, minimum and average readings with RECALL facility. The 72-7250 has RS-232 PC serial interface, user selectable lighting type (tungsten, fluorescent, sodium or mercury, daylight) and zero adjustment by push button. The meter operates from 9V battery.
-
Product
IP-OCTALPLUS232
-
IP-OCTALPLUS232 implements eight EIA-232 asynchronous serial ports, each with RXD, TXD, RTS, and CTS signals. In addition, two ports also have DCD, DTR, DSR, and RI signals. The serial ports are implemented with two Exar ST16C654 quad UARTs. Each channel has two 64-character FIFOs to allow longer interrupt servicing latencies.
-
Product
Continuous Time Interval Analyzer - PXI
GT668PXI-40
-
A true breakthrough in high-speed Time Measurement and test technology, GuideTech’s GT668PXI-40 leverages the power of its CTIA continuous time-stamping technology, eliminating the need for supplemental triggers, pattern markers or clock recovery circuits.GuideTech’s CTIAs enables serial interfaces pattern verification and full jitter analysis in milliseconds for fast, automated characterization and high-throughput production test on all ATE platforms, including low-cost and in-house testers.GT668PXI-40 cards can be expanded up to 36 Channels Single Ended Input in a single 3U PXI chassis.
-
Product
SparkFun Serial Basic Breakout
CH340G
-
The SparkFun Serial Basic Breakout is an easy-to-use USB-to-Serial adapter based on the CH340G IC from WCH. It works with 5V and 3.3V systems and should auto install on most operating systems without the need for additional drivers. The Serial Basic uses the CH340G IC to quickly and easily convert serial signals to USB. It’s a great lower-cost alternative to the extremely popular FTDI Basic.
-
Product
Signal Integrity Studio, Analysis & Simulation SW for WAVEPULSER High-Speed Interconnect Analyzer
WavePulser-Signal Integrity (SI) Studio
Analyzer
WavePulser Signal Integrity (SI) Studio is included as a single license in the WavePulser 40iX-BUNDLE or can be purchased as an additional license for offline access to additional users. WavePulser Signal Integrity (SI) Studio combines S-parameter, Impedance profiling and de-embedding measurements, channel and equalizer modeling, eye diagrams and jitter analysis in a single affordable software package for emulating the complete serial data channel.
-
Product
Test FMC Mezzanine Module
TFMC900
-
The TFMC900 is an FMC (FPGA Mezzanine Card) Mezzanine Module designed to test ANSI/VITA 57.1 FMC Carriers during development or series production. Additionally, it offers the possibility to realise various I/O solutions for connected FMC Carriers. Interconnection of the High Pin Count FMC Connector signals can be verified by JTAG and by functional tests. A loop-back of the 10 multi-gigabit transceiver interfaces allows interconnection checks for the high-speed serial interfaces.
-
Product
Multichannel Voltage Output D/A Converters
-
Analog Devices offers an industry-leading family of multichannel voltage output D/A converters (DACs), covering 8-bit to 16-bit resolutions, from 2-channel up to 40-channel density, and serial SPI or I2C interfaces. This family of precision D/A converters are in demand for applications that require high channel density and a small form factor, such as optical communications, analog output modules, or LED displays. ADI’s multichannel voltage output D/A converters provide features such as the availability of multiple independent output spans, system calibration functions that allow user-programmable offset and gain, or D/A converter increment/decrement functionality, which reduces the need to add external precision gain stages and facilitates the use of this family of D/A converters.
