Mic
Convert sound pressure to an electrical current.
See Also: Microphones, Measurement Microphones, Hydrophones
-
product
Transmitter (Export Only)
SMDB
The input section features the unique servo bias input circuitry with a standard TA5M type jack for use with electret lavaliere mics, dynamic mics, or line level signals. A DSP-controlled analog audio limiter is employed before the A-D converter. The limiter has a range of more than 30 dB for excellent overload protection and a dual release envelope that makes the limiter acoustically transparent while maintaining low distortion. The limiter recovers quickly from brief transients, with no audible side effects, and also recovers slowly from sustained high levels to keep audio distortion low while preserving short term dynamics.
-
product
SparkFun Electret Microphone Breakout
This small breakout board couples an Electret microphone (100Hz--10kHz) with a 60x mic preamplifier to amplify the sounds of voice, claps, door knocks or any sounds loud enough to be picked up by a microcontroller’s analog-to-digital converter. Each breakout comes fully assembled and works from 2.7V up to 5.5V.
-
product
High Definition Audio Daughter Board with Line-in, Line-out and Mic-in
DB-Audio2
- Realtek ALC262 High Definition Audio codec- Three jacks: line-in, line-out and mic-in- 5x2 pin header for cable connection to external audio header on SBC- 4-pin header interface for CD audio output
-
product
Audio Analyzer / Studio Aid
MiniSonic MS10
The MiniSonic MS1/MS10 Audio Analyser/Studio Aid is a complete, hand held, two-channel analogue audio test set that measures frequency, frequency response, phase, level, noise, distortion, crosstalk, speed and path latency (delay).As well as being a quality tester it's a precision line-up tool, a stereo PPM, a balanced-unbalanced convertor (both ways),a stereo mic preamp, a headphone amp, and a level convertor.
-
product
Microwave Communication Trainer
We are instrumental in offering quality range ofMicrowave Products that finds application in satellite communication, broadcast and educational centers. Our range includes microwave test bench, critical microwave band & joint and MIC trainer. These products are known for optimum performance and high efficiency.
-
product
Audio Level Analyzer
BK3011C
In keeping with our goal of constant improvement, we have upgraded our BK3011 MEMS mic tester! The BK3011C is more modular, easier to connect and with the new Test Shop upgrade, easier to use. But the basic features are still the same. Then BK3011C enables you to check mic characteristices over a frequency range using a stable, constant SPL sweep. It still produces both graphs and numerical data but now will automatically classify both PASSing and FAILing DUT's so you can keep track of quality issues and trends.
-
product
Micro Sensor
MIC 1000-20
Advanced Thermal Solutions, Inc.
The MIC 1000-20 micro sensor is designed for measuring fluid velocity and temperature in areas that are densely packed. It can be used where the space between boards is less than 4 mm. The thickest part of the MIC 1000 is just 3.2 mm.
-
product
C-Mic Tester Lite
BK2011
For quick quality assessment or for portable C-mic testing, take a serious look at the BK2011. The BK2011 produces a fast, highly reliable measurement that doesn't include all the extra data given by the BK3010. It's ultra portable, and from your briefcase to testing takes about a minute. If you don't need the full functionality of the BK3010 C-Mic Tester, or if you need an easy to set up, portable machine, ask us about our BK2011.
-
product
Radio & Wireless Compliance Testing
EMC Technologies can provide the mandatory radio and wireless testing, approvals and certification services for major international and local markets such as European CE Marking, USA and Canada FCC and ISED certification, Japan MIC, Australian RCM and New Zealand GURL. Common standards we can test against include:
-
product
SPL Modules
The popular analog sound level meter, now with increased range to work with iAudioInterface2 and the internal mic in iOS 5, which can reach over 120 dB SPL.
-
product
3U CompactPCI Intel® 6th Gen. Quad- Core™ Processor Blade
MIC-3332
MIC-3332 is using Intel® 14nm technology to provide significant performance and power efficiency. It provides an ideal solution for railway rolling stock, high-performance computing and military application. With its optimized design on EMC & thermal, it is available to meet or exceed EN50155.
-
product
High Performance Embedded Box IPC
MIC-7000
The compact modular PC support i-module expansion to satisfy diverse application requirements. Modular computer reduces lead time for CTOS due to easy configuration and can be widely deployed for factory and machine automation.
-
product
6U CompactPCI® Rear Transition Board for MIC-3396
RIO-3316
The RIO-3316 is the first Rear Transition Module (RTM) supporting PCIe connectivity to the main CPCI board enabling significant value-added features and extensions to next generation CPCI blades such as MIC-3396. The RIO-3316 supports: one PS/2 port, one USB 3.0 and one USB 2.0 ports, one RS-232/485/422 ports, two Gigabit Ethernet ports, two PICMG 2.16 LAN ports, one digital and one integrated (digital/analogue) DVI port on the rear panel. One UHM connector on J3 provides PCIe bus and allows supporting USB 3.0 and SATA Gen III (6 Gb/s).
-
product
CPCI-S.0 Standard Compliant Peripheral Board Controlled by a PCIe Channel Derived from the Backplane Connector P1
MIC-3820
MIC-3820 is a 2.5" on board SSD/HDD carrier board running at SATA Gen3 speed. A fast swap of the drive can be accomplished via a reserved thumb screw to help open a door on the front panel and eject the drive. The excellent mechanical design makes it easy to replace modules.
-
product
3U CompactPCI® RS-232/422/485 Serial Communication Card
MIC-3955
The MIC-3955 is a low power 4-port or 8-port RS232/RS422/RS485 serial board with 3U CPCI form factor and is based on the EXAR PCI controller. MIC-3955 is PICMG 2.0 Rev. 3.0 compatible. Rear board module are named MIC-3527XX. The MIC-3955 supports front IO or rear IO with 4-port and 8-port, and every channel is independent.
-
product
6U CompactPCI® PCI Carrier Board
MIC-3961
The MIC-3961 is a 6U CompactPCI® PCI carrier board that allows users to attach a 32/64-bit PCI card via a J1/J2 connector to a CompactPCI platform. The hold-down bracket secures the PCI card onto the carrier board and protects it against vibration and shock. In addition, the bracket allows a cable to be routed through the front slot panel.
-
product
4U CompactPCI® Enclosure with cPCI Power Supply (non-CT Bus)
MIC-3042
The MIC-3042 is a 4U enclosure designed for standard cPCI power supplies. It is equipped with a cPCI 500 W redundant 2 1 power supply with hot-swap support. The system has 8 slots for CompactPCI boards and 6 slots for IEEE 1101.11 rear I/O transition boards. The MIC-3042 comes with a built-in high quality backplane that supports 64-bit / 66 MHz PCI cards.
-
product
6U CompactPCI Intel® Atom™ Processor Blade
MIC-3398
The MIC-3398 is a Low-Power 6U CompactPCI® CPU blade with best in class price/performance ratio tailored for applications that require a state of the art processor platform based on Intel® Architecture with full IO capability at an attractive cost point. The MIC-3398 supports Intel® Atom™ E3845 and Celeron N2930, J1900 SoC (system on a chip) family previously codenamed Bay trail with a maximum of quad-core 2.00 GHz processing performance. Intel® Atom™ technology provides significant increases in performance and energy efficiency by using the 22nm Intel® manufacturing process making it an ideal choice for control and workstation applications that require passive cooling with a power dissipation as low as 10W. Up to 8GB, dual channel 1333 MHz DDR3L memory with ECC support provide a high performance and robust memory interface for demanding applications. With built-in graphics based on Intel® HD Graphics Technology this blade offers a significant improvement in graphics performance compared to previous generation platforms. Support for an onboard 2.5” SATA-II drive as well as CFast SSDs adds comprehensive mass storage support. On the system side, the MIC-3398 supports 32-bit, 33MHz and 64-bit, 66MHz PCI bus interfaces to a CompactPCI backplane. A rich set of I/O interfaces such as DVI-D, USB3.0/2.0, Gigabit Ethernet and RS-232/422/485 ports round off the feature set. In addition to the single slot wide (4HP) board offering, a dual slot wide (8HP) version of the blade offers additional network connectivity by increasing Gigabit Ethernet port count from two to four.
-
product
CPCI-S.0 Standard Compliant Peripheral Carrier Board
MIC-3810
The carrier board provides a PCIe x16 connector for standard PCIe x8, PCIe x4, PCIe x1 PCIExpress® cards supporting PCIe Gen3 speeds. The carrier board can accommodate cards with maximum dimensions of 176 x 68.9 mm (6.9" x 2.7" inches).
-
product
Mic / Audio Line Tester
Qbox
Whirlwind Music Distributors, Inc.
The Qbox is the all-in-one audio line tester ideal for applications such as live sound, maintenance, installation work - anywhere audio runs down a cable. The Qbox can quick-check dynamic microphones and cables without firing up the entire system. It provides a handy mic or line-level tone for activating a signal path or identifying a specific cable in a pile of cable ends.
-
product
3U CompactPCI Serial Processor Blade with 6 COres/12 Thread Core i7 and Xeon Processor
MIC-330 Series
MIC-330 is a 3U CompactPCI® serial processor blade with 6 cores/12 thread Core™ i7 and Xeon® processor and configured with Intel® CM246 PCH to support dual-channel 32GB DDR4-2666, up to 16GB on board memory for rugged applications, and another 16GB are available via the SO-DIMM socket for expansion.
-
product
CPSI-S.0 Standard Compliant Peripheral Board Controlled by a PCIe Channel Derived from a Backplane Connector P1
MIC-3811
It is a dual mini-PCIe carrier board with two onboard SIM card holders and mini-PCIe connectors, routed by PCIe and USB2.0 interface. It allows connection with different types of Mini PCIe form factor add on cards like Wi-Fi/3G/4G LTE/GPS/DIO/CAN/ and MVB modules, either full- or half-size style.
-
product
Dielectric/Conductivity Sensor
Micro-VariconTM
The Micro-Varicon sensor is a miniature, thin, flexible dielectric sensor designedfor cost-sensitive use where space is limited. The electrode array is patterned on apolyimide substrate, and the Micro-Varicon sensor can be supplied with or withoutTeflon insulated leads.
-
product
Profilometer
MicroCam™
MicroCam™ fiber-based optical non-contact 3D profilometers deliver: High-Speed Non-Contact Surface and Cross-Sectional Inspection 3D Online Measurements, GD&T and Imaging Long Stroke Profilometry with Sub-Micron Resolution Thickness, Roughness and Vibration Measurements Fiber-based Probes which reach into Bores, Tubes, and Crevices
-
product
Differential Scanning Calorimeters
MicroCal DSC Range
The "Gold Standard" for structural stability analysis of biotherapeutics, biological macromolecules and polymers in solution. Are microcalorimeters are powerful tools which enable characterization of the thermal stability of proteins and other biomolecules, primarily for biopharmaceutical development and manufacture. They are used for general stability studies, for biosimilarity and batch-to-batch comparability assessment, and for the optimization of purification and manufacturing conditions. MicroCal PEAQ-DSC systems are simple to use, requiring little assay development, and no labelling or immobilization.
-
product
Compact Environmental Chambers
MicroClimate 3
The MicroClimate 3 is a compact environmental chamber designed to simulate a full range of temperature and/or humidity conditions. The small footprint of the MicroClimate 3 combined with temperature and humidity capabilities make this chamber the number one choice for testing small components and products. Whether you need to perform temperature cycling tests or expose your product to steady state temperature environments, these chambers will maintain precise and accurate temperature/humidity control throughout your test.
-
product
Compact Uncooled LWIR Cores
MicroCalibir
The latest advances in the integration of our in-house 12 μm microbolometer pixel technology with a deep-ADC ROIC circuit have resulted in the development of the small and lightweight MicroCalibir™. This compact, low-power uncooled thermal camera platform features the smallest VGA IR core module on the market making it ideal for OEM drones, handhelds, helmet-mounted and vehicular integration products.
-
product
Fixed Gas Detectors
MicroSafe 500 & 600 Series
Teledyne Gas & Flame Detection
MicroSafe 500 and 600 Series gas detectors feature a non-intrusive operator interface. Calibration and programming instructions appear in simple intuitive and sequential script on a 16-character backlit display. The transmitter design incorporates extensive fault diagnostics with each condition conveniently identified on the transmitter display.The 500 Series comes standard with a linear 4-20 mA output, one-man remote calibration, self-adjusting zero and span, and LED indicators for fault and calibration status.The 600 Series includes the same features as the 500 with the addition of 3 alarm relays and an RS-485 serial communications port.Electrical Classification - Explosion proofClass I, Div 1, Groups B, C, D
-
product
Compact PCI AE Chassis
MICRO-II
The Micro-II is an industrial chassis built to enable powerful AE testing capabilities in a compact form factor. Its 4 PCI slots allow it to hold up to 32 AE channels, using Physical Acoustics’ PCI-8 AE boards. It has been designed to operate either as a benchtop system via direct connection to a monitor, keyboard, and mouse, or as a remote system controlled by a notebook computer over its Gigabit Ethernet interface.
-
product
Quad-Core Intel® Atom™ Processor 3U CompactPCI® Card
MIC-3329
The Advantech MIC-3329 is based on Intel® Atom™ technology, previously codenamed Baytrail and is designed to provide balanced performance and power efficiency. The MIC-3329 is a 3U CompactPCI® processor blade designed for dual-core Intel® Atom E3826/E3827 and quad-core Intel® Atom E3845 processors, and up to 4GB soldered DDR3L-1066/1333 ECC memory. It is available in single and dual slot form factor, offering a range of I/O functionality by XTM (8HP) & Rear I/O extensions. Front panel I/O on the single slot (4HP) provides 2 x RJ45 GbE ports (Switchable with RIO 4HP),1 x VGA port (Switchable with RIO 4HP), 1 x USB2.0 port and 1 x USB3.0 port. Front panel I/O on the second layer (XTM) provides 2 x COM ports (RS232/422/485), 1 x PS/2 KB/MS and 1 x Audio ports or 2 x M12 GbE ports, 1 x COM ports (RS232/422/485). The MIC-3329 provides an ideal solution for transportation, railway and factory automation applications. Its robust design from a layout and thermals perspective allows it to meet or exceed EN50155 and EN50121-4 using a very low TDP selection of 7W/8W/10W processors. Its low power consumption and industrial SoC features make the MIC-3329 a perfect fit for all fanless system applications.
