G.992.5
Doubles the bandwidth (ADSL) close up, boosts it nicely in middling ranges and pushes high-speed always-on data over telephone lines out to 18,000 feet.
-
Product
Control Unit
EC-501A & EC-501A(G)
-
Dynatrol® EC-501A and EC-501A(G) Control Unit combines with the DJ and G Series Dynatrol® Level Detectors, including Sealed and Suspended units. Within the Control Units, a SPDT relay is operated from the On/Off signal of the Dynatrol® Level Detector. Simply actuate process control equipment, level alarms or indicator lights from the contacts of this control unit.
-
Product
Insulation Testers
-
Kyoritsu Electrical Instruments Works, Ltd.
The insulation resistance (IR) test (also commonly known as a Megger) is a spot insulation test which uses an applied DC voltage (typically either 250Vdc, 500Vdc or 1,000Vdc for low voltage equipment <600V and 2,500Vdc and 5,000Vdc for high voltage equipment) to measure insulation resistance in either k, M or G.
-
Product
Hall Effect Sensor
907 XP (Explosion Proof)
-
Features • NPN open collector, square-wave output • Zero speed operation with no signal loss • Non-contact, large gap distance sensing • Signal transmits up to 1,500 ft • Simple to install and set up • Powered by 5-24 VDC • Class I, Div I (D) Class II, Div I (E, F, G) Class III • XLB-3 enclosure • Bi-directional option (907B XP)
-
Product
Insulation Tester
AD-225
-
3 Measurement voltage range: 500 V; 1000 V and 2500 V, Control of measuring voltage during measurement, Insulation measurement up to 100 G W, Elimination of trough resistance insulation ? 3 connectors measurement method, Autoranging,
-
Product
96 Sink/Source
YAV90096
-
Selectable voltage and current, comparation and measurement Drive sink or source up to 32 mA per channel Maximum voltage in output selectable from 9 to 24 VDC Possibility to use I7Os in parallel Pin voltage comparator with logic readout at fix +4VDC 10-bit resolution pin voltage measurement with CAN bus value readout Build-in editable test steps sequence (test script) Size: form G
-
Product
Higher Range DC Gauss Meter
329 Series
-
Integrity Design and Reseach Corp.
Portable w/ Dimensions: 5.8"x3.6"x2.5"Range: +/-(20 G, 200 G, 2kG, 20kG)Bandwidth: 68HZ at 3dbComes with 9v DC adaptor & hard carrying caseAnalog Output: +/-200 mV DC FS3 1/2 digit bipolar displayPowered optional either by 9v battery or AC adaptor
-
Product
3U VPX 1 Slot P&G with VITA 67.3D aperture
101V301P05-9002R
-
Power for 3.3V, 5V and 12V are included, rear connectors are all fully loaded, use with Elma’s slot to slot or slot to I/O bulkhead cable products during system development.
-
Product
MEMSIC 2125 Dual-axis Accelerometer
28017
-
The MEMSIC 2125 is a low cost, dual-axis thermal accelerometer capable of measuring tilt, acceleration, rotation, and vibration with a range of ±3 g. For integration into existing applications, the MEMSIC 2125 is electrically compatible with other popular accelerometers. MEMSIC provides the 2125 in a surface-mount format. Parallax mounts the circuit on a small PCB, providing all I/O connections so it can easily be inserted on a breadboard or through-hole prototype area.
-
Product
3U 1-Slot OpenVPX P&G, w/o ROHS, 3.125G
101VPX301P-9005
-
3U 1-Slot OpenVPX Power & Ground, Pass through, RT2-R ruggedized conn, w/o ROHS, Max data rate (Gbps) 3.125.
-
Product
Safety Compliance Test System
EN 60601
-
Test system for electrical safety compliance testing of medical products in accordance with EN 60601-1, 3rd edition.The system is equipped with three test fixtures which are connected in parallel order to reduce the number of setup tasks for different variants in the course of day-to-day manufacturing processes. Its purpose is to test medical products, e. g. patient monitors, which are employed at hospitals to monitor heartbeat and oxygen saturation.Based on the integrated electrical safety tester by Associated Research, in combination with an AC power source and a switching matrix, it is possible to fully automate tests like for instance AC/DC high-voltage tests, insulation resistance measurements, earth connection tests and leakage current measurements.The required occupational safety is provided by a high-voltage safety hood in accordance with EN 501191. The entire safety technology, as well as the control PC, is mounted in an aluminum-profile cart.
-
Product
2D Geophysical Inversion Software for Resistivity and Induced Polarization Data
RES2DINV
-
RES2DINV software is designed to interpolate and interpret field data of electrical geophysical prospecting (2D sounding) of electrical resistivity (conductivity) and induced polarization. The inversion of the resistivity and IP data is conducted by least-square method involving finite-element and finite-difference methods. The software can handle data from any electrode array, including Wenner (a, b, g), dipole-dipole, inline pole-dipole, pole-pole, Wenner-Schlumberger, equatorial pole-dipole and non-conventional arrays. Interpolate data from land, under water, and cross-borehole surveys. Easy data conversion from the most popular geophysical instruments including ABEM Lund, Syskal, AGI, PASI, IRIS, SCITREX, etc.
-
Product
Scales, Modules, Weighing Platforms
-
The weighing platform is a very precise measuring device for determining weights because of its resolution of 1 g and an accuracy of ± 0.1% of measuring range.
-
Product
Media Files Player/Viewer/Analyzer/Converter
VQV
-
VQV is a compact, but powerful program, featuring:Raw YUV/Y4M/BMP files player with sophisticated viewer/analyzer functionalityWide range of frame sizes, input and output formats; powerful "Save as" file format converterDisplays XY positions, YUV and RGB levels of every pixel; switchable zoom ratio and signal gainAutomatic measurement of Active Image size and position – LetterBox and PillarBox detectorYUV and RGB levels display, video frame information, Black Crash and White Crash statistical analysisBuilt-in high-gain spatial and temporal high-pass filters reveal even hardly visible artefactsSelectable RGB, Y, UV, R, G or B view channels, adjustable filter mask size and positionRight-click submenu allows fast creation of snapshots or thumbnail .BMP imagesRunning multiple VQV instances provides for quick frames/profiles comparison and benchmarking Easy-to-use tool, instantly revealing your video camera, codec, scaler, converter or other video device performanceInput and output uncompressed video material data – bit by bit, pixel by pixel, frame by frameFast and effective tool for 3G-SDI/HD-SDI/SDI/HDMI/LAN/WAN equipment testing and video data fidelity verificationIdeal tool for development labs, software developers and high volume manufacturers
-
Product
Aerospace And Defense Software (3000A/T/G X-Series)
D3000AERB
-
MIL-STD 1553 and ARINC 429 triggering and analysis for the InfiniiVision 3000A, 3000T, 3000G X-Series oscilloscopes, along with mask testing, advanced math, video analysis, and more.
-
Product
3U VPX 1 Slot P&G w VITA 67.3C connector in J2
101V301P04-9003
-
Power for 3.3V, 5V and 12V are included, rear connectors are all fully loaded, use with Elma’s slot to slot or slot to I/O bulkhead cable products during system development.
-
Product
Receiver
Elrec Lite
-
The Elrec Lite G is a 2-channel hand held induced polarisation (IP) and Resistivity receiver mostly designed for mineral exploration. This low-weight device is particularly suited for sounding and profiling measurements where the operator must move from several hundreds of meters, carrying the receiver.
-
Product
Bi-Directional-Coaxial LD/PD Module
BiDi-C1000 (CWDM)
-
Hangzhou Huatai Optic Tech. Co., Ltd.
*Tx Laser wavelengths optical : 17 CWDM *Using DFB Lasers *DFB laser optical: with isolation or without isolation *Low threshold current and operating current* High output power *Built-in InGaAsP monitor PD* High responsivity, InGaAs planar PIN detector *Wide temperature range operation(Tc=-40℃to+85℃) *Fiber ITU-T G.657 Bending low loss, fiber optic cable features
-
Product
Low G Sensitive Oscillators
-
Precision Test Systems is increasingly becoming a world leader in ultra-low phase noise (ULN) crystal and rubidium oscillators. We manufacture the CFS10B crystal frequency standard and the RFS10E and RFS10F rubidium frequency standards. All these models can also be locked to the global satellite service operated by the USA (GPS), Russian (GLOSNASS) and Europe (Galileo). We also have a complete range of distribution amplifiers to compliment these frequency standards.
-
Product
Portable Ruggedized Test System
BADGER
-
Badger systems utilize NI's CompactRIO (cRIO), Single Board RIO (sbRIO), and/or CompactDAQ (cDAQ) hardware. The Badger product line offers high speed data acquisition/control and flexibility in an industrial package. Badger chassis and instrumentation have a 50 g shock ratings and a wide -40 to 70 °C operating temperature. These systems are ideal for automotive, industrial automation, remote monitoring, field service, and advanced control applications.
-
Product
Updated Mini-ITX Embedded Board with 6th/7th Gen Intel Core i7/i5/i3, Pentium and Celeron Desktop Processor
AmITX-SL-G
-
The AmITX-SL-G is a Mini-ITX motherboard supporting the Desktop 6th Generation IntelR Core? i7/i5/i3 and PentiumR and CeleronR Processor with IntelR Q170/H110 Chipset. The AmITX-SL-G is specifically designed for customers who need high-level processing and graphics performance with a long product life solution.
-
Product
FD-11605, 8-Channel, ±60 V Voltage Input Device for FieldDAQ
786469-01
-
The FD-11605 can measure up to eight channels with a voltage input range of ±60 V. It features 24-bit resolution with simultaneous sample rates up to 100 kS/s. The FD-11605 offers channel-to-channel isolation, which eliminates noise from ground loops and protects instrumentation circuitry from high-transient voltages of up to 1000 V. The FD-11605 has an ingress protection rating of IP65/IP67 (dust-tight and water-resistant),can operate in -40 °C to 85 °C environments, and can sustain 100 g shock and 10 g vibration. The FD-11605 incorporates Time Sensitive Networking (TSN) and features an integrated network switch and built-in power circuitry for simple daisy chaining. You program the FD-11605 with NI-DAQmx, which automatically synchronizes multiple FieldDAQ™ devices. The FD-11605 is ideal for test cell and outdoor environments.
-
Product
Analog Magnetometer
-
Analog Magnetometer for very low magnetic fields. Measuring range: ±20 G. The solenoid-Tester detects magnetic fields by LED or buzzer.
-
Product
SPS link-up via 24 volt I/Os
HSM-24V
-
The module HSM-24V provides 32 digital inputs/outputs for 24 V level and links ADwin up to e. g. the world of SPS-like signals.
-
Product
cPCI-6540 Series 6U CompactPCI Processor Blade, Extended Temperature
20040257
-
The cPCI-6540 Series is a 6U CompactPCI® processor blade with soldered DDR4-2666 ECC memory up to 32GB and DDR4-2666 ECC socket type memory up to 32GB. The cPCI-6540 features an Intel® Xeon® E, 9th Gen Intel® Core™ and Intel® Celeron® G processor (formerly Coffee Lake-H) with Mobile Intel® CM246 Chipset. The ADLINK cPCI-6540 Series is a 6U CompactPCI blade in single-slot (4HP) width form factor. Front panel I/O includes 1x DP, 2x GbE, 2x USB 3.1 ports, 1x RJ-45 COM port, 1x VGA and 1x PCM/XMC slot. The cPCI-6540V front panel includes 1x DP, 2x GbE, 1x USB 3.1 port and 2x PMC/XMC slots.
-
Product
Banana Plug Test Clip
PCS
-
The PCS-MB Parrot Clip model is a Banana Plug Test Clip of a medium size, with a length of 70 mm, including the metal tip and the button. Its weight is 7 g, Due to the banana connection the PCS-MB Parrot Clip can be connected to different cable leads. This is convenient when you want to use different clips like alligator clips or parrot clips or just the banana plug at the leads. The PCS-MB provides also reliable hands-free connections for different component sizes from SMD with the W1 tip up to the W4 tip.
-
Product
Accelerometers
-
The unit is based on micro machined MEMS technology. The unit contains a 35g sensing element. The element is scaled to optimise the resolution to suit the g range of interest. An internal amplifier provides an output between 0 and 5 volts. The on board microcontroller and temperature sensor are used for offset drift compensation. This unit can be re-calibrated at the factory.
-
Product
Chlorine Meters
-
Water chlorination is the process of adding chlorine (Cl2) to water as a method of water purification to make it fit for human consumption as drinking water. Sper Scientific offers Chlorine meters that meet the standard method 4500-CI G for drinking water and the ISO 7027 standards.
-
Product
3U VPX 1 Slot P&G w VITA 67.3C aperture 10G
101V301P04-9X12R
-
Power for 3.3V, 5V and 12V are included, rear connectors are all fully loaded, use with Elma’s slot to slot or slot to I/O bulkhead cable products during system development.
-
Product
Dispersion Compensation Optical Fiber Module
DCM-G.655-C-Fxx
-
Hangzhou Huatai Optic Tech. Co., Ltd.
Huatai DCM-G.655-C-Fxx dispersion compensation fiber module is designed for single mode optical fiber G.655 C band, dispersion and dispersion slope compensation for wide band, the system optimized residual dispersion. The PCVD module based on optical fiber technology is mature and reliable, can improve the performance of optical transmission system.
-
Product
SINE Sinusoidal Vision Demonstration Array
-
The Sinusoidal Visual Demonstration Array is designed to demonstrate the Modulation Transfer Function (MTF) of the human eye. Its transmittance varies sinusoidally and increases in spatial frequency from 0.2 to 20 c/mm, following a logrithmic scale. The modulation increases linearly from top to bottom. One can see, in the image, where the visual contrast contour disappears which is the MTF of the eye. Ideally suited for teaching and demonstration, the Array is available on film mounted in glass (-G), or mounted in a 2″x 2″ projection slide.(-SL)
