-
product
Multiple Instrument Station
SYSTEM 8 MIS 4
The Multiple Instrument Station MIS4 provides you with all the instruments required for the test and measurement of electronic components and PCBs. ABI's SYSTEM 8 MIS4, along with the Ultimate software, is a faster and more economical solution than using traditional oscilloscope, metering and other bench test instruments, and can quickly produce the required Pass/Fail or other test and debug results.
-
product
Micro Coax, Contact, ITA, 75 Ohm, RG179
610141103
Primary mating contact 610140103. (May mate with other Receiver contacts, as well.)Mechanical SpecificationsDurability 10,000 cyclesContact Material Center Conductor – BeCuShield – BrassContact Plating 50µ" Au over 100µ" NiContact Termination Center Conductor - SolderShield - CrimpInsulator PTFEMating Force 1.5 lbs max [0.68 kg]Electrical SpecificationsCharacteristic Impedance 75ΩFrequency Range DC – 2 GHzVSWR 1.39 @ 2 GHzInsertion Loss – √f(GHz) x .06 dBDWV 800 V RMSContact Resistanc...show more -
product
Talk Set
OTS-20
OTS-20 Multifunction Optical Talk Set enables clear and long distance telephony on single optical fiber. Featuring integrated laser source and optical power meter for loss test, OTS-20 is a reliable toolset for tough environments.
-
product
PXI Precision Resistor Module 3-Channel, 3 to 22.3M
40-297-154
This PXI Precision Resistor module provides a simple solution for applications requiring accurate simulation of resistive sensors. The 40-297 series is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems. It is particularly well suited to applications such as the testing of engine controllers where resistive sensors provide information on parameters such as temperature.
-
product
MXG X-Series RF Analog Signal Generator, 9 kHz to 6 GHz
N5181B
Take your devices & designs to their limit with outstanding hardware performance, including unmatched phase noise & spurious characteristicsDrive power amplifiers & characterize nonlinear behavior with industry-leading output powerThoroughly test receiver performance by simulating complex analog modulation scenarios with multi-function generator capabilityLower your cost of ownership with 3-year cal cycles & comprehensive solutions for self-maintenance
-
product
EDFA
SOA1550-32(64)
Hangzhou Softel Optic Co., Ltd.
*Single/dual input for choice, built in optical switch for dual input, the switching power can be set by the button in the front panel or by web SNMP.*Output adjustable by buttons in the front panel or web SNMP, the range is down 4dBm*Maintenance function of one-time downward attenuation of 6dBm by buttons in the front panel or web SNMP, to facilitate the optical fiber hot-plug operation without turn off the device*Multi- ports output, can built in ...show more -
product
Drivetrain Tester
G5.DT
The G5.DT series is bidirectional regenerative. It was developed specifically for testing DC components of the electrical drive train or DC components of other parts of the vehicle electrical system. It is suitable for use in laboratories and on test benches. The modular and finely graded G5.DT series is characterized by highly dynamic response times and a wide current-voltage range with an auto-ranging factor 3. The power supplies are equipped with a powerful CAN multi-protocol interface (1 kHz, 16 bit) and optionally offer test bench relevant safety functions such as PL e according to EN ISO 13849, insulation monitoring as well as automatic discharge on the load side in case of shutdown.
-
product
Probe Series
VEGA Series
MPI VEGA Prober series is ready to meet the diverse test and material handling requirements of the Laser Diode (VCSEL, EEL) and optical module markets. MPI VEGA probers are based on a highly flexible and reliable platform, enabling the test of a wide variety of device types (Wafer, Package & Singulated Die) over temperatures with the ability to handle thin/warped wafers. Multiple probing schemes are also supported with the ability to probe small pads with well-controlled needle force.
-
product
Digital Push And Pull Force Gauge
HG-2-1000
Shenzhen Chuangxin Instruments Co., Ltd.
Digital push and pull force gauge is a universal portable force device, testing push and pull load. It is small, light, easy to take, multi-function, high precision. Applicable for all products doing push and pull load test, insert and pull out force test, destroy test, etc. It also can be combined with the machine and clamp to make up a small tester for different purposes.
-
product
Antenna, Biconica-log
EM-6917C-1 | 26 MHz – 1 GHz
The EM-6917C-1, a hybrid combination of the industry standard biconical and log periodic antennas, delivers an unmatched combination of frequency coverage and high power handling capability. Featuring exceptionally broad frequency coverage of 26 MHz to 1 GHz, the EM-6917C-1 eliminates the need for adjustments or switching antennas in most test applications up to 1 GHz, and it does so without compromising power handling capability for transmit applications.
-
product
PXIe-2526 , 158‐Channel, 2 A PXI Multiplexer Switch Module
780587-26
158‐Channel, 2 A PXI Multiplexer Switch Module—The PXIe‑2526 is a high‐density PXI multiplexer switch module that is ideal for routing signals within automated test systems. It uses electromechanical relays to perform immediate switch operations in either a 158x1 1‑wire or 79x1 2‑wire multiplexer topology. The PXIe‑2526 also features onboard relay counting for relay monitoring.
-
product
Water Quality Testing Instrument
GDYS-101SC
Water quality analysis meter, single element. Each model can test one element contained in water.
-
product
CAN & LIN bus Custom Test & Simulation Software
CanX
Schleissheimer Soft- und Hardwareentwicklung GmbH
CanX is the custom testing and simulation software for CAN and LIN bus for specific user groups. The run-time software is designed to execute predefined or automated tasks in testing, work preparation, production, repair or project management.
-
product
Respirator Fit Test Adapters
TSI Fit Test Adapters for PortaCount Respirator Fit Testers provide an easy, practical alternative to the probed method of quantitative respirator fit testing. Respirator Fit Test Adapters enable quantitative fit testing for individuals wearing their own respirators. Use the Fit Test Adapters spreadsheet to find the right fit test adapter. You can search for respirator manufacturer, the respirator model, and in some cases, the respirator’s filter/regulator connection. Click on the links in the document, or below, to see more details about a fit test adapter and your purchase options.
-
product
Advanced Power Supplies
N7900 Series
The Keysight Advanced Power System (APS) N7900 Series is a full-featured supply designed for automated test equipment (ATE) applications that benefit from high-speed dynamic sourcing and measurement. The highly integrated N7900 enables you to accelerate your test-system throughput with industry-leading speed and precision measurements. The APS N7900 has all the capabilities of the N6900 but also includes dynamic output power, dynamic measurements, and higher accuracy. While standard on the N7900, high accuracy, dynamic sourcing, and power are available as separate options on the N6900.
-
product
RFFE Protocol Analyzer and Exerciser
PGY-RFFE-EX-PD
Prodigy Technovations Pvt. Ltd.
RFFE Protocol Analyzer (PGY-RFFE-EX-PD) is the Protocol Analyzer with multiple features to capture and debug communication between host and design under test. The RF Front-end control interface (RFFE) Serial bus interface is emerging as a chosen for controlling RF frond end devices. There are variety of front end devices such as Power Amplifiers (PA), Low-Nose Amplifiers (LNA), filters, switches, power management modules, antenna tuners. It is widely used in mobile devices.
-
product
PXI Source Switching Module
40-618-001
The 40-618 PXI Source Switching Module consists of 12 separate 4-channel multiplexers and 44 uncommitted SPST relay contacts in a single width PXI module. Typical applications include signal routing for avionics test systems that conform to the ARINC 608A specification.
-
product
2kV, 400 MHz High Voltage Differential Probe
HVD3220
The HVD3000A series of high voltage differential probes cover the fullest range of applications, from 120/240 V switch-mode power supplies through 600 V class and 5 kV electrical apparatus. The table below provides a list of recommended probe models based on specific device under test applications.
-
product
NI-9260, 51.2 kS/s/ch Simultaneous, 3 Vrms, 2-Channel C Series Voltage Output Module
783467-01
51.2 kS/s/ch Simultaneous, 3 Vrms, 2-Channel C Series Voltage Output Module - The NI‑9260 is an instrument-grade dynamic signal generator for testing the audio components and capabilities of consumer electronic devices and providing excitation in structural test applications. Unlike sound card-based solutions, the NI‑9260 can be deployed quickly and recalibrated to guarantee long-term measurement repeatability and decreased test time. It also features ±30 V overvoltage protection and short circuit protection.
-
product
ARINC 664 Part 7 Test & Simulation Interface for PCI
PCI-C664-V2
Avionics Interface Technologies
Supports IEEE 802.3 10/100/1000 Mbit/s Full-Duplex Ethernet links - Utilizes SFPs to support both copper and optical interfacesSimulates multiple ARINC 664 End Systems - VL traffic shaping and input VL redundancy management - Supports up to 4K Output VLs and 4K Input VLs - Supports up to 16K Sampling & Queuing output message ports and up to 16K input Sampling & Queuing message ports - ARINC 653, UDP, IP protocols managed onboard - IRIG-B time code encoder/decoder - Automatic message sequ...show more -
product
Battery (EV) Automatic Test System
Landrex Technologies Co., Ltd.
Battery (EV) Automatic Test System
-
product
Walk-In Conditioning Test Chamber
Weiber Walk in Conditioning Test Chamber offers an ideal apparatus for conditioning materials at non-ambient temperatures. Now researchers, engineers, and technicians have a simple and cost effective method to condition samples prior to testing. Laboratory Conditioning Chamber is designed for the conditioning of samples prior to testing, provides conditions from 20% to 98% RH ± 2 and 0°C to 94°C ±0.5°C.Conditioning Test Chambers offers ideal humidity and temperature conditions required for testi...show more -
product
Elisa Microplates
The ELISA method is a test which is used in immunology and other scientific fields to detect antibodies and antigens. ELISA stands for Enzyme-Linked Immune Sorbent Assay, which refers to the fact that antibodies coupled to enzymes are used to determine the results of the test.
-
product
VirtualBench All-in-One Instrument
The VirtualBench All-in-One Instrument combines a mixed-signal oscilloscope with protocol analysis, an arbitrary waveform generator, a digital multimeter, a programmable DC power supply, and digital I/O. The all-in-one features are simple, convenient, and provide more efficient circuit design, debugging, and validation. The included software lets you view all measurements on a single screen and can be updated with free software releases to add functionality and value. The VirtualBench All-in-One Instrument easily integrates with LabVIEW software to provide programmatic control and automated test sequences.
-
product
Data Recording System
DataMAX II
DataMAX II is a state-of-the-art Windows 2000 based analog instrumentation recorder designed to replace traditional tape based data recorders. Using the latest technology, DataMAX II eliminates the time consuming methods of the past with a single precision instrument that will replace a tape recorder, data acquisition system, and monitoring scopes. From calibration to analysis, a test can now be run in a fraction of the time, with far greater accuracy than was possible with traditional analog recorders.
-
product
Camera Barrel Test System
BK8612
We designed the BK8612 2 Channel Noise Test System to provide noise and vibration testing for your digital camera barrel DC Motors. Because it is based on the BaKo BK2120B DAQ, it is capable of monitoring a microphone and an accelerometer concurrently to obtain data from the motor. Because you can change the parameters of functions and limits, it is versatile but still quick and easy to set up. In addition, you can look at data in real time and also store it for future analysis. Easy to use and set up, fast and accurate; if you need to maintain the quality of your camera barrel motors, this is the tester you want.
-
product
OTP-Based Test System
Power electronics assemblies often cannot be tested using conventional technology for their electrical performance. Due to the adaptability of the instrumentation, the OTP concept offers an ideal platform even beyond the space requirements of several control cabinets. In order to achieve high test flexibility with different assemblies, the system was equipped with three-phase AC sources and AC loads as well as a precise three-phase power meter. DC sources and loads with different current and vol...show more -
product
Audio + Vision Generation and Monitoring
Test Chest 3G (Multi Function Test)
Quick and very easy to use, the amazing Test Chest boasts instantaneous Audio + Video generation and Monitoring. NO tedious boot-up means Test Chest is “First out of the blocks” every time by 10s of seconds, and it’s intuitive touch-screen speeds Engineers to the required function, saving precious time and giving their investigations a real head start. 10bit precision signal generation is standard with Test Chest, as are the analysis utilities which are displayed on it’s superb 5” high resolu...show more -
product
Broadband Horn Antenna (4GHz - 40GHz (calibrated from 18GHz))
PowerLOG® 40400
• Extremely wide frequency range from 4GHz to 40GHz (calibrated from 18GHz to 40GHz) • Supports high input levels up to 300W (peak) or 150W (CW) • High gain up to 17dBi • Delivered including specific calibration data • Perfect for EMC and immunity tests with Spectrum Analyzer.
-
product
Breakout Box
A piece of electrical test equipment used to support integration testing, expedite maintenance, and streamline the troubleshooting process at the system, subsystem, and component-level by simplifying the access to test signals