-
product
Water Vapor Permeability Tester
QT-WVP
Qualitest Water Vapor Permeability Tester QT-WVP series is used to test the water vapor transmission rate (WVTR) of packaging materials.
-
product
Parallel Electrode SMD Test Fixture, DC To 3 GHz
16196D
The 16196D surface mount devices (SMD) test fixture offers excellent repeatability and usability, with accurate correlation up to 3 GHz. 16196 series fixtures are custom designed to fit specific SMD sizes (see table below), and provide repeatable DUT positioning with reliable contacts to enable stable measurement results – reducing the possibility of operator-induced error. Traditionally, SMD inductor evaluation up to 3 GHz has been difficult to implement – now with the 16196 series, it’s easy to perform accurate and repeatable measurements.
-
product
Test Block & Plug Systems
Test Block system is an evolution of the 14 test circuit versions widely employed in the power utility sector. The primary difference is the incorporation of ‘finger safe’ test sockets which allow the use of shrouded 4mm banana plugs.
-
product
Precision Mechanical Calibration Kit, DC To 26.5 GHz, 3.5 Mm
85052C
The Keysight 85052C precision mechanical calibration kit contains precision standard devices to characterize the systematic errors of Keysight network analyzers in the 3.5 mm interface. This kit also contains adapters to change the gender of the test port and a torque wrench for proper connection.
-
product
PXI High Density Precision Resistor Module, 3-Channel, 3.5Ω to 773kΩ
40-298-143
The 40-298-143 is a high density programmable resistor module with 3 channels which can be set between 3.5Ω and 773kΩ with 1Ω resolution The 40-298 range provides a simple solution for applications requiring accurate simulation of resistive sensors. The 40-298 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems.
-
product
High Speed Cable Production Tester
GRL-V-DI20
GRL-V-DI20 provides a fast and easy way for anyone to test cables for manufacturing defects and signal integrity specification requirements. GRL-V-DI20 provides comprehensive test coverage in seconds at a fraction of the cost of similarly-capable bench test equipment.
-
product
Suspension/Road Contact Tester
VLT3673-G6
The VLT 3673-G6 suspension / road contact testers operate according to the well-known EUSAMA principle. However, the diagnostic options are not restricted to the contents of this specification. In addition to the usual road contact values, the following values are also measured and displayed: the contact value difference, resonance frequency and wheel weight at minimum contact value, tyre rigidity, wheel weight and axle weight. There is a general final evaluation so that all these values do not have to be interpreted after every test.
-
product
Test Solution Requirements Gathering
When we first talk to our customers about their test requirements, they generally know what they want to achieve but often do not have the detailed requirement specifications to enable us to design and build a suitable test system for them. The process of generating a detailed design specification is both time consuming and stressful, so we understand the challenges this causes.
-
product
Networking and Telecom
LAN for a long distance networks, Networks and Telecom AOIP range includes a complete set of test tools and certification.
-
product
Multi-function Tester
MFT5010
It can be used to test insulation resistance, continuity, loop impedance and RCCB, earth resistance tester, five major test requirement in the electrical testing industry. Phase indicator. Can check a wide range of 3-Phase Power source from 110V to 600V
-
product
RF Testing, Screening and Qualification
DPACI has extensive experience in providing RF testing, screening, as well as QCI services to a diverse range of customers, such as Lockheed Martin, General Dynamics, and Ball Aerospace. We have a fully equipped RF and microwave lab with test capabilities ranging from 40 GHz to 300 GHz for providing RF packaging.
-
product
Nanomechanical Test System
Hysitron TI Premier
Bruker’s Hysitron TI Premier nanoindenter was specifically designed to deliver industry-leading, quantitative nanomechanical characterization within a compact platform. Built upon proven Hysitron technology, the TI Premier provides a broad suite of nanoscale mechanical and tribological testing techniques.
-
product
80W Power Supply, 35V, 2.2A or 60V, 1.3A
E3645A
Keysight basic DC power supplies offer essential features for a tight budget. The single & dual output, 30-100 W GPIB E3640 series provide small, compact size for bench and system use; low output ripple and noise; and built-in measurements and basic programmable features. The Keysight 78W, single output E3645A is a stable and reliable power supply for benchtop and basic automated test applications, and enables versatile solutions for tests that require moderate speed and precision with both GPIB and RS232.
-
product
ADB Bearing Sensor Tester
The ADB Sensor Tester (ADBT) has been designed to test 4B adjustable depth bearing (ADB) style temperature sensors in the field. During planned maintenance or periodic testing, the ADBT can be used as a diagnostic tool to verify the alarm and shutdown sequences of the control unit are functioning as expected. The unit operates in two testing modes, direct (heated) and indirect (simulated).
-
product
T3DSO1000HD Series Oscilloscopes
T3DSO1000HD Series
The Teledyne Test Tools T3DSO1000HD Oscilloscopes feature four channel bench models with analog bandwidth options of 100 MHz and 200 MHz each with 12 bits of vertical resolution. Each model offers a maximum sample rate of up to 2 GSa/s sample rate and a maximum memory up to 100 Mpts. The series comes with all serial data trigger & decode options as standard alongside Power Analysis and Bode Plot capabilities.
-
product
Phase Sequence Indicators (Contact Type)
862 PR
Standard Electric Works Co., Ltd
● Two functions in one unit: open phase and phase sequence detection.● Neon light indicators.● Large size alligator clips for easy clipping onto switch- boards terminals.● Checks a wide range of 3-phase power sources.● Ideal for installing conveyor lines, pump systems and interconnected drivers.● Waterproof design, protection class : IP24.● Special test leads length are available on request.
-
product
Miniature Quartz Force Sensors
Often the test engineer will try to take low level measurements with a sensors not rated for these low levels. Due to insufficient sensitivity the resulting data may be noisy, hard to analyze or unusable. Using the appropriately sized and ranged PCB Miniature Quartz Force Sensor solves the problem and gives reliable data at a Low Amplitude level. The miniature sensor configuration permits low-amplitude, dynamic compression, tension, and impact force measurements.
-
product
FINNtrometer
FINNtrometer™ is a plug-n-play module for testing 1 to 12 LEDs and can be daisy chained to test up to 254 LEDs with a single USB or Serial cable
-
product
Network Virtual Test, Service Activation & Performance Monitor
Fusion
Fusion is the premier product in the VIAVI NITRO platform, which addresses the challenges of test and measurement for new virtual and hybrid networks. As part of the NITRO VNet solution set which is focused on virtual service activation and performance management, Fusion arms network operators and enterprises with a valuable set of standards-based test tools that deliver accurate test results on which managers and engineers can depend.
-
product
Fibolocator
Fibolocator is an innovative device for measuring and characterizing breaks and other backscattering-causing faults in optical fibers. Time-resolved correlation reflectometry is the principle on which the device is based. It analyzes the backscattered light like a pulse OTDR, but unlike such OTDRs, cw laser diodes are used. The requirements for the test signal and the complexity of the system are low, which leads to very low costs for OEM subsystems.
-
product
Universal Testing Systems up to 600 kN (135,000 lbf) Force Capacity
5980 Series
5980 Floor Model Testing Systems are universal, static testing systems that perform tensile and compression testing; and also perform shear, flexure, peel, tear, cyclic, and bend tests. The 5900 Series are engineered for precision, built for durability, and offer the flexibility for changing requirements. They are designed with standard and optional features that increase testing efficiency and improve the testing experience for the operator. 5980 floor models are robust, heavy-duty frames commo...show more -
product
Dust Test Chamber
Sanwood Environmental Chambers Co ., Ltd.
Sand Dust chamber provide an environment to test the exposure of automotive and electronic components to concentrated levels of dust in order to validate product seal integrity.
-
product
Fastest Flying Probe Test System for Semiconductor Substrate Interconnect Test
GATS-3200
* Test individual packages or * Test Multi-image panels with Step&Repeat Function * single flying probe top using very high speed voice coil motor (VCM) technology * 50 - 100 tests per second ... high throughput * Dual Flying Probe Top for testing bump-to-bump nets * flying probe head allows testing of all nets including each power and ground point * 4-wire test capability
-
product
Battery Resistance Tester
BT-3915
Kongter Test & Measurement Co., Limited
Regular test of battery internal resistance or battery conductance is essential for stationary batteries. It is also recommended by latest regulation of IEEE 450, IEEE 1188 and IEEE 1106. The excellent performance of BT-3915 for testing battery internal resistance and voltage will help you pick out the weak batteries and ensure their performance in short time measurement.
-
product
GPIB Digital Interface
Model 4863
ICS's 4863 GPIB Digital Interface provides a fully enclosed parallel interface that is suitable for benchtop or rack mount applications. OEM board versions available for inclusion in test chassis.
-
product
CW Test Transmitters / Signal Generators
The WTX CW test transmitter family is particularly designed for field applications such as Inbuilding site modeling (model calibration), DAS injection / testing, walk-testing as well as outdoor path model tuning- thanks to its broad range of optional power amplifiers.
-
product
Continuous Time Interval Analyzers
GT210PXI-15
GuideTech’s GT210PXI-15 3U form factor, meets industrial standard chassis with an expandable platform, achieving optimal test system with optimal cost. The ability to precisely resolve frequency and time yields both increased accuracy as well as reduced measurement time.
-
product
Satellite & Payload Check-Out Systems
Rovsing delivers systems for complete satellite or satellite subsystem testing. Rovsing has developed a modular test system architecture, based on S/W and H/W modules developed by Rovsing for most common space interfaces such as Power, TM/TC, MIL-STD-1553B and SpaceWire. A dedicated test system can then be composed by configuration of the modular architecture, installation of monitoring and control software, as well as test definition and scheduling software as required. Besides reduced development time, this has the advantage that the system to a large extent consists of elements that have been validated on previous missions.
-
product
WiGig RF Tester
IQgig-RF Model B
When used in conjunction with IQgig-IF, an optimized test solution for conducted testing of WiGig chipsets and baseband modules, the IQgig family products provide a total test solution for R&D characterization and high volume manufacturing.
-
product
Antenna Test & Measurement Solutions
MVG offers the broadest choice of solutions based on near-field, far-field and compact range measurement techniques for Antenna, EMC, RCS and Radome testing. Our solutions support the measurement needs of the Aerospace & Defense, Telecommunications and Automotive industries, as well as Academic and Research institutes. MVG standard systems are customizable, facilitating selection, allowing for specifications, and guaranteeing an upgrade path for the enhancement of system capabilities. From components and parts to full turn-key solutions, the right combination enables our customers to meet specific measurement needs in a variety of testing configurations.