-
product
Glow Wire Test Apparatus
GWT A2
GLOW WIRE TESTER (also known as Glow Wire Test Apparatus) is designed to carry out fire hazard testing as specified in IEC 60695-2-10 2000-10. Flammability test is to check the ‘Resistance to Fire’ of electrical insulators that touch directly conducting parts & also parts of insulators. This test is also referred in many other standards such as IS 11000, IS 3854 : 1997 / IS 1293 :1988 / IS 371 :1999 & IS 11000 Pt 2 Sec 1, IEC 60335, IEC 884/94, IEC 60598, IEC 61058, BS 6458, BS EN 60695–2-10,11,12, etc.
-
product
Programmable DC Power Supply
CBCT
The CBCT is a variable voltage DC power supply designed specifically to test substation circuit-breaker Open and Close coils. The CBCT uses the substation’s DC power supply to electronically generate a programmable output voltage from 5% to 95% of the source voltage. The CBCT can maintain up to an 80A test current while maintaining 2% or better voltage regulation during the circuit breaker coil operation.
-
product
Electrical Safety Tester
GSC60
One instrument for all electrical safety tests and Power Quality analysisGSC60 was designed with the aim of making safety of electrical installations visible and valuable, easily and quickly.
-
product
EBIRST 50-pin D-type To 25-pin D-type Adapter
93-005-414
eBIRST is a range of USB controlled test tools capable of performing automated path resistance tests on Pickering Interfaces PXI, LXI or PCI controlled switching solutions. Each tool simply interfaces with the switching system's connector so a test can be run using the supplied Windows-based software.
-
product
PCI High Density Pecision Resistor Card, 9-Channel, 3Ω To 102kΩ
50-298-034
The 50-298-034 is a high density programmable resistor card with 9 channels which can be set between 3Ω and 102kΩ with 2Ω resolution The 50-298 range provides a simple solution for applications requiring accurate simulation of resistive sensors. The 40-298 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems. It is particularly well suited to applications such as the testing of engine controllers where resistive sensors provide information on parameters such as temperature.
-
product
Photovoltaic System Bypass Diode Tester
FT4310
Hioki is pleased to announce the launch of the Bypass Diode Tester FT4310 for Photovoltaic Systems. The FT4310, which is designed to test bypass diodes in strings of crystalline photovoltaic cells, can be used to detect open and short-circuit faults in bypass diodes by string either in daylight or at night. The instrument is the first portable device capable of detecting bypass diode open faults in operating panels (without requiring the panels to be shielded from sunlight).
-
product
PCI Precision Resistor Card 3-Channel, 3Ω To 1.51MΩ
50-297-150
The 50-297 provides a simple solution for applications requiring accurate simulation of resistive sensors. The 50-297 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems. It is particularly well suited to applications such as the testing of engine controllers where resistive sensors provide information on parameters such as temperature.
-
product
EVSE Test Platform
To manage both the challenging high-power requirements of electric vehicle supply equipment and the market demand, it is crucial to rely on a test system that performs to your specs. The right system needs to combine the tools for reliable asset communication, microgrid management, effective protocol simulation and high-power testing. This EVSE platform combines the right energy regeneration equipment with 25+ years of test experience to deliver the results you need to meet conformance in the time you need it.
-
product
CellCorder Battery Tester 'EU Series'
CRT - 400
The new CRT-400 is the latest version in the leading line of CellCorder battery test instruments. Lightweight, stylish, rugged and durable. Special features include new user-friendly operation, USB and IR data transfer, modem, graphical reflective LCD display for better contrast, and new cables and clamps.
-
product
Digital Battery & Electrical System Analyzer w/Printer
726
*Accurate Battery & Electrical System Tester *Features programmed test for new Start/Stop Batteries 3 Testers in ONE! 1) 6 & 12 Volt Battery Tester + 12V Start/Stop Battery Test 2) 12 & 24 Volt Charging System Tester 3) Alternator-Starting-Charging System Tester *Wide Testing Range from 40 to 2,000 CCA *Built-in Printer - print the results for permanent service records *Removable/Replaceable Cable Set *Patented Dynamic Resistance Technology
-
product
Cable Testing
MET Labs performs a wide range of cable tests required by a wide range of vendor and government specifications, including simultaneous temperature and vibration testing.
-
product
Inclined Impact Testers
Inclined impact testing simulates environmental dynamic forces that packaged goods may endure throughout transport and handling operations. These hazardous dynamics are simulated using impact test systems. Inclined impact test systems utilize a carriage that propels the test sample down a ramp at predetermined velocities before impacting into a fixed backstop. The specimen’s reaction to these extreme conditions indicates how the product would fare in real-world supply chain settings, allowing design engineers to make improvements to either the product and/or the protective packaging as needed.
-
product
SIMRC - RS232 to I2C Converter PCB
1080-001
Pickering Interfaces Series 1000 SIM Reed Relay Cards offer a choice of switching configurations using low cost industry standard SIM connectors. They are ideal for placing switching systems in fixtures close to the unit under test.
-
product
Test Equipment
ST9020
Shenzhen Star Instrument Co., Ltd.
The ST9020 single-phase energy meter test equipment is full-featured and stable. Optional accuracy classes are 0.1 and 0.05. As divided by structure there are combined type, integrated type and auto wiring type. The meter test equipment is controlled via PC-based software. Choices of meter position are 6, 12, 24, 30, 48 and 60.
-
product
Radar Altimeter Test Set
Core Technology
Eastern OptX core technology enables the conversion of microwave signals to optical signals (E/O), time delaying this signal then reconverting the light back to original microwave signal (O/E) with superior fidelity over traditional time delay methods. Products include Radar Target Simulation, Radar Altimeter Testing, Channel Simulation (Air Interface) and Multipath Creation.
-
product
Insulation Tester
CENTER 365
Insulation Test Range Up To 20GΩ, Test Voltages Of 50V, 100V, 250V, 500V and 1000V For Insulation Test, >1mA Short-Circuit Test Current For Insulation Test, Live Circuit Detection
-
product
Fungus Test
The fungus test assesses the extent to which material will support fungal growth and how any fungal growth may affect performance. The fungus test also identifies how rapidly fungus will grow on the material, and how fungus affects the material, its mission, and its safety for use following the growth of fungus on the material.
-
product
Optical Path Converter
LS512A/LS512B
There are many LED manufactories using two integrating spheres and one spectrophotometer to do test. The previous testing way is: when you use big sphere to test, the customer need to connect the detector cable and optical fiber from the Spectrophotometer to the big sphere, after the calibrating and then you can do the test. When you use the small sphere, you need to take away the detector cable and optical fiber from the big sphere to the small sphere, then need to calibrate again. It is t...show more -
product
Portable Oscilloscopes
ScopeMeter Portable Oscilloscopes take you into territory that standard bench oscilloscopes cant readily withstand, harsh, hazardous and dirty industrial environments. These hand-held instruments combine the performance of a bench oscilloscope with a multimeter and paperless recorder for installing, commissioning and maintaining industrial and electronic equipment out in the field. Fluke ScopeMeter test tools use a unique Connect-and-View mode to automatically and continuously setup the oscilloscope making them easy to use even on complex signals.
-
product
VITA 62, 3U Test Fixture
TF-3U-7B041-1
This Power Supply test fixture is being proposed as a tool for checking Injector / Ejector operation, proper alignment of the VITA 62 connector and proper alignment of both keys on a Single slot, 3U, VITA 62/SOSA power supply.
-
product
Microfluidic Device Manufacturing Solutions
We provide production automation solutions for microfluidic device manufacturing with precise liquid dispensing. We offer solutions for your POC test, molecular and immunodiagnostics and microfluidic devices manufacturing.
-
product
ELECTRONIC MEGOHMMETER
MI-2550e
The MI-2550e general purposes megohmmeter is a truly portable equipment suitable to measure insulation resistances using test voltages up to 2,5 kV. It employs high-reliable, state-of-the-art technology for accurate measurements of ultra high insulation resistances up to 5.000.000 MΩ with four test voltages: 0,5 kV - 1 kV - 1,5 kV - 2,5 kV.
-
product
Kjeldahl Method (Auto Analyzer)
Automatic Kjeldahl Analyzer is an automatic, smart device determining nitrogen content based on Kjeldahl method. It can be widely used in food processing, feed production, tobacco, livestock, soil fertility, environmental monitoring, medicine, agriculture, scientific research, teaching, quality control and other fields for the test of nitrogen or protein content with respect of macro and semimicro samples and can also be used for the test of ammonium, volatile fatty acid / alkali, and so on.
-
product
RF Switches
Marvin Test Solutions’ switch card portfolio includes matrix, multiplexer, and RF multiplexer configurations. 3U and 6U PXI switch cards feature easy to use, reliable, and integration-friendly D-sub style interface connectors – a feature unique to Marvin Test Solutions PXI switch cards. GENASYS switch cards are compatible with MTS’s family of GENASYS Switching and Switching/Digital Subsystems, featuring integrated MAC Panel SCOUT receivers.
-
product
12 VOLT CIGARETTE SOCKET TESTER
MDPPTSTCIG
*Provides the user with a simple way to test a 12V cigarette socket on a vehicle*Mini probe will light up when 10.8V - 15.4V is detected
-
product
Hot Air Ageing Oven
Premier Electrosystems' Hot Air Ageing Oven is a testing instrument that is used for analyzing the aging effect on the products and materials. It is used by different industries and product manufacturers to heat the products for conducting the dry tests in the laboratory. This helps manufacturer study the accelerated effects of ageing of the sample in a very short time.
-
product
Microwave/RF Cable Test Assemblies
PHASEFLEX
For test applications that require precise, repeatable measurements, microwave/RF test assemblies from Gore provide excellent phase and amplitude stability with flexure. Our rugged, lightweight assemblies deliver reliable performance with longer service life and reduced equipment downtime resulting in lower costs for testing in laboratory, production and field test environments.
-
product
EMC Test System
An electric product might cause the malfunction to other electric appliances by discharging the emission noise from it, or is oppositely caused the malfuction by the emission noise from other electric appliances. The former is checked by the EMI test and the latter is checked by the EMS test. The international standard like the CISPR standard is provided so that such an accident should not happen, and the manufacturer must declare by themselves beforehand that their product meets the standard. The generic name of the EMI test (Electro-Magnetic Interference) of the emission measurement and the EMS test (Electro-Magnetic Susceptibility) of the immunity
-
product
Capacitance Meter
A piece of electronic test equipment used to measure capacitance, mainly of discrete capacitors.
-
product
BMS Test System
6020
High Extensibility: for multi-string battery cell, 4 cells per channel, expandable from 1 to 16 cells per strings