-
product
IEC60529 Hand-held IPX3/4 Spray Nozzle For Waterproof Test
CX-IP3/4
Shenzhen Chuangxin Instruments Co., Ltd.
IEC60529 Hand-held IPX3/4 Spray Nozzle for Waterproof Test is strictly designed according to the requirements of IPX3 and IPX4 code of GB4208 and IEC60529 standard. The IEC60529 Hand-held IPX3/4 Spray Nozzle for Waterproof Test is used to test waterproof performance of the appliance and electronics.
-
product
Plug Pin Durability Test Device
IEC60884 Fig30
Shenzhen Chuangxin Instruments Co., Ltd.
IEC60884 fig30 plug pin durability test deviceSuitable for checking the tightness of the plug pin,Check the tightness of the plug pin according to the standard, and customize the pin hole gauge of other national standards.
-
product
Halogen Moisture Analyzer
LD-LHMA-A12
Halogen moisture analyzerLD-LHMA-A12with benchtop design, user can manually open the door of heating chamber for analysis. Incorporated with halogen heating lamp for rapid and uniform heating, it determines the moisture content and dry weight of the test sample. It continuously measures and immediately display the loss of moisture and weight on backlight LCD screen during test.
-
product
Mobilize
A complete wireless solution that connects your Pronk test equipment to your smart device!* Take complete control of your Pronk products — Safe-T Sim® Mobilize Electrical Safety Analyzer, Mobilize SC-5 SimCube® NIBP Simulator, Mobilize OX-2 OxSim Flex® SpO2 Simulator, and Mobilize FlowTrax® IV Pump Analyzer — to set up your own test protocols or run your CMMS procedures right from your Apple iOS device.
-
product
PCI-7811, 1M Gate Virtex-II FPGA, Digital Reconfigurable I/O Device
779363-01
The PCI‑7811 is a reconfigurable I/O (RIO) device that features a user-programmable FPGA for onboard processing and flexible I/O operation. With LabVIEW FPGA, you can individually configure the digital lines as inputs, outputs, counter/timers, PWM, encoder inputs, or specialized communication protocols. You can also program custom onboard decision making that executes with hardware-timed speed and reliability. The PCI‑7811 is well-suited for a wide variety of applications, such as high-speed waveform generation, sensor simulation, hardware‑in‑the‑loop (HIL) test, custom communications protocols, bit error rate test, and other applications that require precise timing and control.
-
product
Root Cause Failure Analysis
Maintenance Reliability Group, LLC
Root Cause Analysis of Grease Lubricated Components: Root cause analysis includes a complete root-cause failure report and recommendations for further monitoring and corrective actions. MRG will test for grease consistency, oxidation, product contamination and wear metals utilizing Grease Thief® Analyzer die extrusion test, FTIR, RULER and RDE Spectroscopy. Testing includes Analytical Ferrography and Rheometer testing. Testing can include the submission of a failed component for extraction of gr...show more -
product
Concrete Comprission Testing Machine
CONCRETO 2000X/3000X
CONCRETO Series This compression testing machine can safely and efficiently perform tests at a high capacity without causing explosive fracture (failure of the specimen) on ultra-high-strength concrete, which is used as a structural material in high-rise buildings, etc. This one machine can be used for materials ranging from ultra-highstrength concrete to specimens that have been recently cast, mortar, etc.
-
product
Switches
Whether you are performing high-accuracy, low-speed measurements on a dozen test points or high-channel, high-frequency characterizations of integrated circuits, National Instruments delivers a flexible, modular switching solution based on PXI or SCXI to help you maximize equipment reuse, test throughput, and system scalability.
-
product
Test Adapter
cPCI/VME/VME64x
The test adapter is used for measurement and testing of test specimen boards, which gives optimal access of signals, address lines as well as power from backplane assembly. Usually the test adapter includes fields for voltage and amp, current measurements and in some cases also some pins for wire wrap to conduct custom connections.
-
product
DMX Tester
DMXter 2U
Here's the DMXter 2U, a Lil'DMXter2 for bolted down applications. All the hardware and software features of the standard Lil'DMXter2 in a 2U 19" rack box, plus many new features.The user controls, the XLR connectors, and the LED illuminated LCD display are on the front panel. The 2U is equally at home as the back up controller in a theatre or TV studio, running a trade show booth, the background lighting for themed entertainment or as the built in test controller in a touring show DMX distribution rack. Its increased I/O capabilities will make it a useful addition to your test bench.
-
product
OMCD Version 4 Test Track CD For OmniMic V2
Designed for use with the Omnimic but is also useful as a standalone test CDGreat for setting amplifier gain levels19 test tracks
-
product
Drop Tester
AccuDrop 125
Model AD-125 is 1 of 3 models in the ACCUDROPTM Series. It helps determine the ruggedness of packagesand the effectiveness of their interior cushioning when exposed to impact during material handling. Theeffects of dropping are easily duplicated in your laboratory using the controlled and precise flat, corner, andedge drop tests.
-
product
Environment Tester
ZhangZhou Weihua Electronic co.,ltd
A test of new software that determines whether all transactions flow properly between input, output and storage devices. Typically done by systems programmers, an environment test ensures that all the parts of the system are in place.
-
product
Series Flame Detector
DF-TV7
Teledyne Gas & Flame Detection
The device offers a wide range of output options, as standard and is suitable for use in SIL 2 applications. The detector can be configured to communicate with a wide range of fire panels, controllers, and PLCs and offer HART 7 and Syntel (Lonworks) protocols for addressable event monitoring. The devices come standard with a configurable 4-20mA or 0-22mA (PLC) output, two configurable alarm relays, and two detector status LEDs.All MultiFlame detectors are equipped with a continuous optical len...show more -
product
MIPI Test Fixtures and Tools
In order to support our MIPI test services, UNH-IOL has designed and created test fixtures and software tools to aid in performing C-PHY, D-PHY, DSI, and CSI-2 testing.
-
product
Clamp-on Transducer
CA1000D
Measure current without disconnecting circuit under test. Measure to 1000A DC or AC. Outputs 1mV per Amp, operates on 2V range of any DMM.
-
product
120-600V Solenoid Voltage&Continuity Tester
1867
Peaceful Thriving Enterprise Co Ltd
Test voltage from 120-600V AC/DC polarity and continuity.
-
product
Clips
A complete offering of the most desired electrical test clips and electronic test clips including alligator clips, miniature alligator clips, crocodile clips, battery clips, heavy duty clips, general purpose clips, telecom clips, and many more.
-
product
Software
Besides the primary WITE32 Test Environment package at the heart of our spinstand-based test systems, Guzik offers a variety of software options to provide additional measurement accuracy and analysis. Control and Automation software enhances various electro-mechanical capabilities of the test system (such as servo accuracy), and the available suite of Analysis software tools provides deep insight into the drive component under evaluation. Adjacent Track Interference, 3D Pulse Profile, Media Scanning and Bit Error Rate are examples of some of the optional additions. Some software tools require the WDM5000 Waveform Digitizer to be part of the overall test system.
-
product
Energizer SILVER Vibration Exciter for Buzz, Squeak & Rattle (BSR) Testing
Energizer SILVER
The Energizer SILVER Series is part of a family of extremely quiet vibration exciters. The Series is ideally suited for the support of subjective and objective BSR evaluations according to industry test specifications, such as GMW14011, GM7293TP, BMW PR311-2 or PSA “Specification bruit parasites”, as well as several Hyundai Engineering Standards. With availability in four unique models and sizes, the Energizer Series is expressly designed to support such evaluations, while reducing the risks of measurement uncertainty caused by unwanted vibration exciter noise occurring within the BSR test environment.
-
product
ELM Electronic Load Module
Circuit breakers are often overlooked during maintenance of electrical systems in aircraft, or often only verified for open and closed states. To test the true functional purpose of a circuit breaker it requires the application of current in excess of the rated trip value and then measure the time for the breaker to actually trip. This is the only way to verify that a circuit breaker will react as designed if an electrical failure occurs.
-
product
VeriStand
VeriStand helps you get your hardware-in-the-loop or test cell control and monitoring system up and running quickly. With a wide range of out-of-the-box functionality that includes configurable data acquisition and logging, test sequencing, and simulation model integration, VeriStand reduces the time needed to test your products. You can also use a variety of software tools to add custom functionality to VeriStand, which makes it flexible enough to adapt to even the most complex applications. Choosing VeriStand gives you the confidence that your test system will perform reliably while providing the flexibility you need to meet your real-time test requirements.
-
product
Meter test station
TS23
Calmet Smart Calibration Devices
Three phase reference standard of accuracy 0.02% (or 0.04%). It makes possible electricity meters testing on the site or in the laboratory up to 3x120A/600V
-
product
MCB Test Option, Monitor Voltage Adapter
PTE-FCB
The PTE-FCB / PTE-FCD can be used to effectively reduce the sensitivity of the monitor input. The monitor input detects the relay’s operation and stops (or starts) the chronometer when testing with the PTE-100-C, PTE-50-CE, PTE-50-CET, and all LETs excluding the LET-400 (which lacks a chronometer).
-
product
Fuel Cell Test Stations
The Fuel Cell Test Stations provides control of flow, temperature and pressure for the anode and cathode gases. The station incorporates a DC electronic load. The Station also includes two humidity bottles, an Operating Manual and a computer utilizing LabView-based software.
-
product
True Concurrent Test
TestStation Duo
The TestStation Duo is a true concurrent test system with independent test modules providing fast in-circuit test throughput and lowering high-volume production costs.It effectively doubles the test throughput of conventional in-circuit test systems, without doubling capital equipment costs or increasing manufacturing floor space, by combining two complete and independent test modules inside a single tester frame.
-
product
Automotive Test Systems
Ono Sokki Automotive Test Systems - flow meter, non-contact speedometer, engine tachometer, crank angle detector, and more
-
product
Trainings, Seminars, Workshops
To make your staff able to face daily tasks and handle with high productivity is in the center of our trainings. Especially when a new test sytems starts to run it is extremely important that the personnel can operate appropriately from the beginning.Our workshops are designed as classroom trainings so everybody can concentrate completely on the workshop contents without being bothered by day-to-day business or other troubles.An alternative is the training in-house so we can look after individua...show more -
product
Conventional Panel-mounted Type Power Amplifier Control Unit
PAT01
PAT01 is a power amplifier control unit that controls timing output and reference signal test source for power amplifier.
-
product
DC System Tester
VAFDT220
Substation DC System Tester is applied to test battery charger(voltage stabilizing accuracy, current stabilizing accuracy, ripple factor etc.), battery bank discharge, and monitor the charging process of battery bank.