-
Product
System Amplifier
SAM100
-
The R&S®SAM100 system amplifier is an ultra-broadband solid state microwave amplifier with a frequency range from 2 GHz to 20 GHz. With a power of up to 20 W, outstanding linearity and very good noise characteristics, the R&S®SAM100 amplifier is ideal as a compact system amplifier in various measurement setups e.g. design (DVT) and product validation test (PVT) or EMC. In measurement environments with R&S generators, frequency analyzers or network analyzers, they can act as drivers or boosters and amplify the measurement signals
-
Product
Digital Quad-channel High-frequency Lock-In Amplifier -
eLockIn 204
-
Digital quad-channel high-frequency Lock-In Amplifier.
-
Product
LVDT Sensor Amplifiers
-
Analog Devices signal conditioning ICs, together with linear variable differential transformers (LVDTs), can be used to convert mechanical position to a dc voltage. The IC provides both the excitation for the LVDT and the output conversion to dc level with a user selectable gain. ADI LVDT signal conditioners are available to interface with a wide range of LVDTs, including half bridge and standard 4- and 5-wire.
-
Product
1.0µm PM Fiber Amplifier ( PM YDFA )
HAPM1000
-
Hangzhou Huatai Optic Tech. Co., Ltd.
Huatai HAPM1000 is a Polarization Maintaining Fiber Amplifier which worked in 1050~1080nm operating wavelength. Adopt Polarization Maintaining (PM) ytterbium-doped fiber, output optical power range 0.5W~5W, extinction ratio >20dB.
-
Product
10mA One-Channel Amplifiers
-
USB connected devices have become common in lab environments. The nano box USB is a standalone piezo amplifier with 16 bit D/A resolution. Its small size and powerful amplifier includes a USB 2.0 interface that offers a variety of helpful commands.
-
Product
Full Wave Recorder
I-FullWaver
-
The I-FullWaver systems were specifically developed for precise full waveform time domain induced polarisation, Resistivity and self-potential measurements. Each system is fully independent; incorporating its own power source, GPS module and digital memory for up to 3 months continuous recording.
-
Product
Difference Amplifiers
-
A difference amplifier is a special purpose amplifier designed to measure differential signals, otherwise known as a subtractor. A key feature of a difference amplifier is its ability to remove unwanted common mode signals, known as common mode rejection (CMR). Unlike most types of amplifiers, difference amplifiers are typically able to measure voltages beyond the supply rails, and are used in applications where large dc or ac common-mode voltages are present. They are ideal for current and voltage monitoring. Analog Devices offers a range of difference amplifiers, optimized for low distortion, low power, or high voltage performance.
-
Product
LTP-25 High Performance Long Travel Probe
LTP-25
ICT/FCT Probe
Current Rating (Amps): 8Average Probe Resistance (mOhm): 8Test Center (mil): 100Test Center (mm): 2.54Full Travel (mil): 400Full Travel (mm): 10.16Recommended Travel (mil): 317Recommended Travel (mm): 8.05Overall Length (mil): 1,460Overall Length (mm): 37.08Full Travel Remark: Full Travel for LRP-25TJ: 340 (8.6) and Full Travel for all Ultra High springs: 350 (8.9)
-
Product
RF Benchtop / EMC Amplifier (110/220V)
-
RF-Lambda is a world leader in the design and manufacture of high-power, solid-state, broadband AC-powered EMC power amplifiers.
-
Product
1.5µm PM Ev-Yb Fiber Amplifier ( PM EYDFA )
HAPM5000
-
Hangzhou Huatai Optic Tech. Co., Ltd.
Huatai HAPM5000 is a C-Band Polarization Maintaining Optical Amplifier which worked in 1540~1570nm operating wavelength. Adopt Polarization Maintaining (PM) Multiclad Ev-Yb fiber, output optical power range 27~37dBm(0.5W~5W) ， extinction ratio >20dB.
-
Product
Load Cell Amplifier Signal Conditioner with Removeable Terminals
MODEL LCA-RTC
-
The LCA-RTC Module provide low-cost, dedicated signal conditioning for a single bridge type load cell or torque sensor. Model LCA-RTC comes with removable screw-clamp terminal connectors, which accept wires without soldering.On- board jumper selections include sensitivities from 0.5 mV/V to 10 mV/V, bandwidths from 100 Hz to 30 kHz, and amplified outputs of 0 to ±5V, 0 to ±10V, 0-16 mA, 0-20 mA or 4-20 mA. Zero and span adjustments are via precision 25-turn low-tempco metal film potentiometers.The units can be operated next to the sensor with 4-wire hookup or at distances up to 1 km (3300 feet) with 6-wire hookup. An onboard 87.325 kΩ resistor allows easy shunt calibration at the push of a button. Provision is also made for a user-furnished calibration resistor. Power requirements are 11.8 to 26V DC with load currents from 10 to 60 mA, the latter applying when the unit provides 10V DC excitation to a 350 ohm load cell and delivers a 20 mA analog output.
-
Product
OEM Femtosecond/Picosecond Laser and Amplifier Modules
-
They provide output wavelength options at 780 nm, 925 nm, 1030 nm, 1064 nm and 1550 nm and can be used as stand-alone systems with a user-provided 5 V DC power supply or integrated into higher power laser platforms. The high quality ultrafast pulse streams are perfect seed sources for chirped pulse amplifier systems used in diverse applications, such as high precision microelectronics micromachining, laser eye surgery and nonlinear spectroscopy.
-
Product
Stand Alone/ Bench Top Load Cell Amplifier/ Conditioner Module
MODEL TMO-2A
-
The TMO-2A Transducer Modules is a complete differential amplifier/signal conditioners with self contained power. The unit provide excitation, balance and span adjustment via precision 10 turn pots, and shunt calibration necessary to couple a user supplied bridge type transducer to an indicating instrument. Zero to full scale output is specified at 4-20 mA. The TMO-2A provides a floating shunt calibration circuit which applies calibration at the transducer, thereby eliminating errors due to line losses. The excitation supply incorporates a Wagner Ground to greatly improve Common Mode Rejection. The factory set bandwidth of the module is narrow to improve stability. The removal of a single capacitor will increase the frequency response DC to 60K Hz for dynamic data applications.
-
Product
Wave Quality Analyzer
APQM-707
-
This equipment is a power quality analyzer according to the European standard EN 50160. The Amperis APQM-707 is a high-tech product that allows universal measurement of the parameters of 50/60 Hz electrical networks, as well as the analysis and recording of these parameters.
-
Product
SparkFun Qwiic Thermocouple Amplifier
MCP9600 (Screw Terminals)
-
The MCP9600 Breakout is a high accuracy Thermocouple Amplifier equipped with an I2C interface, accessed over our Qwiic system. Inside the chip are two temperature sensors, one for the thermocouple itself (the hot junction) and one for the chip itself (the cold junction). As a result, the MCP9600 can read both the ambient temperature and the temperature of whatever you're trying to measure! The MCP9600 can do both with a resolution of 0.0625°C, and an accuracy of ±1.5°C (worst-case). The MCP9600 Thermocouple Amplifier is one of our many Qwiic compatible boards! Simply plug and go. No soldering, no figuring out which is SDA or SCL, and no voltage regulation or translation required!
-
Product
CATV Booster Optical Amplifier
HA5100
-
Hangzhou Huatai Optic Tech. Co., Ltd.
Huatai HA5100 series is a CATV booster optical amplifier with gain spectrum band within 1540~1563nm. This kind of optical amplifier is designed for the application of single channel or 1~8 continuous ribbon channels (ITU wavelength). Generally, fiber CATV system operates in single wavelength that has no strict requirement on gain flatness. HA5100 booster amplifier is featured with low NF, high-saturated output power. It is applicable for central bureau, sub-bureau and line relay, as well as other optical communication network. HA5100 is applied most commonly and widely compared with other optical amplifier in CATV system.
-
Product
Transimpedance Amplifiers
-
Current-to-Voltage Amplifier for use with Photodiode-Based Detectors. Transimpedance Amplifiers, Standalone Devices with Data Acquisition as well as Display Function (Optometer). Log/Lin Switching Amplifiers, etc.
-
Product
Isolation Amplifier Analog Output
-
This coupler is an optically coupled isolation amplifier that uses an IC with a high-accuracy sigma-delta A/D converter and a GaAIAs light-emitting diode with high-speed response and high luminance efficiency on the input side, and an IC with a high-accuracy D/A converter on the output side. This coupler is designed specifically for high common mode transient immunity (CMTI) and high linearity (nonlinearity) applications, making it ideal for current sensing in motor drives.
-
Product
High-Voltage Amplifiers - to 1000 Volts peak-to-peak
-
These amplifiers provide high amplitudes and bandwidths, and are well suited for use as booster amplifiers for lower-voltage arbitrary waveform generators.
-
Product
Conventional Panel-mounted Type Power Amplifier Control Unit
PAT01
-
PAT01 is a power amplifier control unit that controls timing output and reference signal test source for power amplifier.
-
Product
Shortwave Plus 50 MHz Power Amplifier
OM2000A+
-
Thank you for purchasing this new model of the OM Power’s RF power amplifiers line for HF and 50 MHz amateur radio bands. You now own, the OM2000A+, an automatic unit with no knobs, no rotaryswitches on the front panel, just two small switches and one large touch display.Smart design, modern conception, high reliability is the result of OM Power’s development and many years of experience with overall solutions and special attention with the design of the protection circuits.This product is covered by two years of warranty on the amplifier itself and one year for the tube.We wish you will have many years of trouble-free use of this equipment, lots of fun and successful contacts in the world of amateur radio.
-
Product
Alternate 0.99 (28.00) - 6.00 (170.00) Long Travel Bead Probe
BPLT-25C-6
Bead Target Probe
Current Rating (Amps): 8Average Probe Resistance (mOhm): 8Test Center (mil): 100Test Center (mm): 2.54Full Travel (mil): 350Full Travel (mm): 8.89Recommended Travel (mil): 317Recommended Travel (mm): 8.05Mechanical Life (no of cycles): 500,000Overall Length (mil): 1,460Overall Length (mm): 37.08Full Travel Remark: Standard Spring: 400 mil / 10,16 mm, Alternate Spring 400 mil / 10,16 mm, High Spring: 400 mil / 10,16 mm, Ultra High Spring: 350 mil / 8,89 mm
-
Product
19-inch Rack Mount(2U) 20 Watts 80MHz to 1GHz Power Amplifier
-
Chengdu KeyLink Microwave Technology Co., Ltd.
20 Watts 80MHz to 1GHz amplifier in a compact 2U package for oversea market. It is a rack mountable-unit incorporating a universal voltage power supply and a built in forced air-cooling system. This amplifier subsystem utilizes LDMOS power device that provides excellent power density, high linearity, low distortion and wide dynamic range. The KB00810S43A SSPA is ideal for EMC testing to various industry standard as well as Broadband Communication.
-
Product
Lock-In-Amplifiers
-
Current and voltage inputWorking frequency up to 45 kHzAdjustable sensitivity, time constant and phaseLocal and remote controlCompact and EMI-shielded case
-
Product
Dual Relay Trip Amplifier
SEM1630
-
The SEM1630 is a DIN rail mounted trip amplifier which accepts RTD, Thermocouple, mV and passive current signals and provides a dual trip output
-
Product
Amplifier Systems
RF Amplifiers
-
Systems are complete. They plug into an outlet and are ready to go. Our standard systems are 3U, which is 5.25″ and 5U, 8.75″. Systems are available with or without IEEE-488, RS-232 and Ethernet connectivity. Amplifiers Systems are available in both Broadband and Band-Specific frequencies.
-
Product
Standard Amplifiers
-
Teledyne RF & Microwave, a Business Unit of Teledyne Microwave Solutions (TMS), supplies catalog and custom RF and microwave amplifier designs for aerospace, defense, and industrial applications. These standard amplifiers, originally designed by Teledyne Cougar, provide both excellent stability and cascadability.
-
Product
Fiber Pigtailed Tapered Amplifier
-
The AOSense tapered amplifier (TA) provides a coherent high-power beam, inheriting all properties from the seed source. TA’s are an essential optical component for quantum sciences, such as laser cooling and trapping, cold atom sensors, electromagnetically induced transparency, and quantum spectroscopy. The TA is also used in commercial laser modules, including master oscillator power amplifier (MOPA) lasers and external cavity lasers.
-
Product
Solid State Broadband High Power Amplifier 1900 - 6000 MHz / 200 Watts
2215
-
The 2215 is suitable for octave bandwidth high power CW, modulated and pulse applications. This amplifier utilizes high power GaN devices that provide wide frequency response, high gain, high peak power capability and low distortions. Exceptional performance, long-term reliability and high efficiency are achieved by employing advanced broadband RF matching networks and combining techniques, EMI/RFI filters, and all qualified components. for EMC, RF Product Test, Communications and Electronic Warfare applications.
-
Product
Amplifiers
-
CAES manufactures custom amplifiers in a wide variety of configurations from LNA (Low Noise Amplifiers), Medium and High Power, and wideband solutions.
