Rapid IO
"the unified fabric for Performance Critical Computing"; rapidio.org
-
Product
Analog I/O Boards
-
General Standards Corporation is a leading supplier of a wide range of high speed Analog I/O boards for embedded applications on several form factors/buses, and for many operating systems. See our selection tables below.
-
Product
LVDS Digital I/O with Virtex-6 FPGA - PCIe
Model 78610
-
Model 78610 is a member of the Cobalt® family of high-performance PCIe boards based on the Xilinx Virtex-6 FPGA. This digital I/O board provides 32 LVDS differential inputs or outputs plus LVDS clock, data valid, and data flow control on a front panel 80-pin connector. Its built-in datacapture and data generation feature offers an ideal turnkey solution as well as a platform for developing and deploying custom FPGA-processing IP.
-
Product
FPGA Digital IO XMC
XF07-523
-
Curtiss-Wright Defense Solutions
The XF07-523 is a rugged Kintex-7 FPGA based XMC with digital IO. The combination of direct high-speed I/O ports and FPGA processing makes the XF07-523 ideal for demanding applications including radar, imaging and test equipment across commercial and defense market spaces. The XMC form-factor is ideal to SWaP constrained platforms such as UAVs and fighter aircraft.
-
Product
Rapid Decompression Test Chambers
CA-RD(H)
-
CSZ's rapid decompression test chamber is designed to simulate rapid decompression for testing aircraft avionics. The environmental chamber meets the environmental conditions and test procedures for airborne equipment referenced in the RTCA DO-160 test specification. The DO-160 specification was designed to test sudden pressure changes starting from 8,000 feet to 60,000 feet (536 to 55 Torr) in 15 seconds. An altitude of 8,000 feet (536 Torr) was used for the initial cabin altitude and 60,000 feet was used for the final cabin altitude after decompression. This test specification is used to identify failures of materials inside of the cabin and the reaction to the surrounding environment.
-
-
Product
Isolated Digital I/O DAQ Cards
-
Advantech isolated digital I/O cards have a wide range of products lines in PCI-bus, isolated DIO, ISA-bus, PC/104 and CPCI platforms.
-
Product
128 Channel Digital I/O With 6 Channel Counter
DP-cPCI-3015
-
DP-cPCI-3015 is a 128 channel TTL compatible Digital Input / Output card with 6 counter channels. The DIO can be programmed as input or output in groups of 16 channels.
-
Product
PMC Digital IO Board
MS 1815
-
*Bus Interface:- 32 Bit PCI Bus with PMC Interface*Speed of operation up to 66MHz*Spartan-3AN FPGA based design*128 channel digital I/O signal*Input/output ON state=3.5V to 5.0 max at -24mA*Input/output OFF state= 0.8max at 24mA*16 groups of 8 channels can be programmed as input/output*Driver interface for Windows2000/XP/VISTA and LINUX OS*Self Test future
-
Product
PC/104 OneBank I/O Board
EMC²-KU40
-
Sundance Multiprocessor Technology Ltd.
The PCIe/104 OneBank™ design enables the EMC²-KU40 to be added to robust and rugged installations for various commercial, medial, industrial and military uses and to enable more versatility the EMC²-KU40 also incorporates a VITA57.1 FMC™ LPC connector opening up an range of extra possibilities and expansion options.
-
Product
Modular I/O via Ethernet
2601 Series
-
100/10 Mbps Ethernet gateway to 2600 series I/O modulesFour RS-232/422/485 ports for remote serial devicesIntegral support for interlock and emergency stop circuitsNetwork watchdog shuts off I/O upon client faultHigh-performance network stack: up to 1000 transactions/secondUltra-fast, one second boot-up timeOptically isolated serial communication to I/O modulesWatchdog TimerCE CompliantCompatible with Linux and Windows
-
Product
Intelligent A/D I/O Unit
RAD242
-
Model RAD242 is an intelligent, two-differential-channel, 24-bit analog-input interface unit that includes a Delta-Sigma A/D converter. The converter has a digital output filter with adjustable notch frequency from 10 Hz to 2000 Hz. The pod also has 13 bits of digital input/output. A precision 10 VDC voltage that can be used for transducer excitation is available at connector pin 5. As much as 60 mA current can be provided. It is packaged in a NEMA 4 enclosure for remote installation in harsh environments. RAD242 also provides a user-definable interrupt input and counter/timer input. An optional RAD Firmware Development Kit is available if you wish to use those user-programmable input lines or to develop a custom program.
-
Product
PCI Analog IO Board
MS 1803
-
*Bus Interface:- PCI Bus*Analog Inputs:- 16 Single Ended Inputs / 8 Differential Ended Inputs*Input Resolution:- 16 Bits*Input Range:- ±10V*Gain:- Programmable Gain Control (1, 2, 4, 8, 16)*Sampling Rate up to 100Ks/S*Peak Measurement +ve and -ve peak for all input channels
-
Product
8Relay(PhotoMOS)/14DI/6DO IoT Modbus/OPC UA Ethernet Remote I/O
ADAM-6360D
-
OPC UA empowers Modbus I/O users to access the industrial IoT world.OPC UA I/O links SCADA and the cloud without the need for gateways, accelerating OT and IT convergence.Hardware and software double security levels to prevent being hacked.Cost-effective: high I/O density and daisy-chaining solution saves cost.
-
Product
Isolated Relay I/O Card
mPCIe-IIRO-8
-
The mPCIe-IIRO-8 consists of a type F1 PCI Express Mini Card (mPCIe) interface board that connects to a Mobile-ITX-sized, DB-37M Isolation Module via an included 9” cable. That module is designed to be easily panel-mounted in any application environment. It uses the high speed PCI Express bus to transfer digital data to and from the card. The digital I/O is compatible with 8255 PPI chips making it easy to program.
-
Product
I/O Modules
-
*Configurable input / output functions*Direct connection of hydraulic valves or joysticks*Modules with M12 connector or central plug*High-performance CAN interface for various communication tasks*E1 type approval (German Federal Motor Transport Authority)
-
Product
CB-68LPR, I/O Connector Block
777145-02
Terminal Block
68-Pin Female VHDCI Right Angle to 68-Pin Female Screw Terminal, Desktop Mount Terminal Block - The CB-68LPR is a terminal block with 68 screw terminals for easy connection of field I/O signals to 68-pin NI data acquisition devices. It includes one 68-pin male connector for direct connection to 68-pin cables. This CB-68LPR features standoff feet for use on a desktop or mounted in a custom panel. The CB-68LPR also has a right-angle-mounted, 68-pin connector.
-
Product
FPGA with Digital I/O PCIe Mini Card
TMPE633
-
The TMPE633-10R provides 26 ESD-protected 5V-tolerant TTL lines, the TMPE633-11R provides 13 differential I/O lines using EIA 422 / EIA 485 compatible, ESD-protected line transceivers and the TMPE633-12R provides 13 differential I/O lines using Multipoint-LVDS Transceiver.
-
Product
PIM-Universal-IO
-
The PIM_Universal_IO facilitates rear panel IO in cPCI based systems using PMC's. The PIM_Universal_IO provides the PMC front panel IO where rear panel IO is desired. The PIM_Universal_IO can be used with any PMC implementing "Pn4" IO.
-
Product
Analog I/O and Digital Receivers
-
Curtiss-Wright Defense Solutions
Many mission-critical applications require small form factor solutions, but cannot compromise ruggedization requirements or I/O and processing performance. Our VPX, XMC, PMC and FMC module-based sensor I/O solutions are designed to handle the toughest operating environments while packing maximum functionality in a minimal physical footprint.
-
Product
DB9M-Pigtail, 9-Pin D-SUB Male to Pigtail I/O Cable, 1 m
157867-01
Multifunction Cable
9-Pin D-SUB Male to Pigtail I/O Cable, 1 m
-
Product
IO Expander
AD16x2DA16x8-125ETH
-
The IO Expander is an additional module to provide more input and output capabilities to the AD16x2DA16x8-125ETH. Via high speed link it connects 8 TTL inputs, 16 TTL outputs, 8 SPDT RF switches, and a GPS module.
-
Product
Digital I/O Cards
104-DIO-48E
-
The circuits use an 82C55A PPI with mode 0 supported. Ports A, B and C are buffered with 74ABT245 transceivers and pulled up to 5V. The optional 82C54 has three-sixteen bit down-counters within one chip. These counters are useful for making frequency outputs, measuring frequency of square waves, pulse width outputs, pulse width measurements etc. Software drivers are provided on CD.
-
Product
PXIe-7857, Kintex-7 160T FPGA, 1 MS/s, DRAM PXI Multifunction Reconfigurable I/O Module
784146-01
Multifunction Reconfigurable I/O
Kintex-7 160T FPGA, 1 MS/s, DRAM PXI Multifunction Reconfigurable I/O Module—The PXIe‑7857 features a user-programmable FPGA for high-performance onboard processing and direct control over I/O signals to ensure complete flexibility of system timing and synchronization. You can customize these devices with the LabVIEW FPGA Module to develop applications requiring precise timing and control such as hardware‑in‑the‑loop testing, custom protocol communication, sensor simulation, and high-speed control. The PXIe‑7857 features a dedicated A/D converter (ADC) per channel for independent timing and triggering. This design offers specialized functionality such as multirate sampling and individual channel triggering, which are outside the capabilities of typical data acquisition hardware. The PXIe‑7856 also includes peer‑to‑peer streaming for direct data transfer to other PXI Express modules.
-
Product
PC/104 Multifunction Analog I/O Boards
104-AIO16A/E
-
The 104-AIO16A is a high-performance 16-bit resolution PC/104 board which provides speeds up to 500kHz for 16 single-ended or 8 true differential analog input channels. This multifunction board features an excellent price/performance value for precision PC/104-based data acquisition, control, or signal analysis of standalone environmental test stations, compact production test equipment, portable testers, avionics and other applications.
-
Product
Digital I/O Card w/CoS IRQ
PCIe-DIO-48S
-
The PCIe-DIO-48S is a 48 channel PCI Express (PCIe) card designed for use in a variety of digital I/O applications. It uses the high speed PCI Express bus to transfer digital data to and from the card. The digital I/O is compatible with 8255 PPI (mode 0), making it easy to program. This also allows for simple and trouble-free migration from other ACCES PCI digital I/O cards.
-
Product
16-bit, 200KHz, 16SE/8DIFF Isolated AI, 4 12-bit AO, 8 Optically Isolated Dig. I/O, 24V, 24 TTL I/O
APCI-3116-16
-
The APCI-3116 is a 16-bit multifunction board for 3.3 V and 5 V PCI systems, with optical isolation up to 1000 V and a high throughput rate of 200 kHz. The PCI board has additional types of conversion: Sequence RAM, Auto Refresh, scan, timer or external event.Furthermore, the board has a PCI DMA, 2 watchdogs, 4 digital inputs and 4 digital outputs. Sensors, which allow to supply current signals instead of voltage signals, also can be acquired with the APCI-3116, as this board offers up to 16 current inputs. The board is protected against overvoltage and input filter and it is protected against high frequency emmission. With the free calibration tool you can do the fine adjustment on-site.
-
Product
Remote I/O
-
Reduces wiring costs, simplify troubleshooting and minimize downtime with Omron's high density I/O modules and other socket-based I/O products.
-
Product
USB-6000, 8 AI (10 kS/s), 4 DIO USB Multifunction I/O Device
782603-01
Multifunction I/O
8 AI (10 kS/s), 4 DIO USB Multifunction I/O Device - The USB‑6000 is a low-cost, multifunction DAQ device. It offers analog I/O, digital I/O, and a 32-bit counter. The USB‑6000 provides basic functionality for applications such as simple data logging, portable measurements, and academic lab experiments. The device features a lightweight mechanical enclosure and is bus powered for easy portability. You can easily connect sensors and signals to the USB-6000 with screw-terminal connectivity. The included NI-DAQmx driver and configuration utility simplify configuration and measurements.
-
Product
CPCI Or PXI Analog IO Board
MS 1808
-
*Bus Interface*PCI Bus Interface, 6U Form Factor*Facility for Calibrating all Output channels*Hot Swap facility*Driver interface for Windows2000/XP/VISTA and LINUX OS
-
Product
Digital I/O Board, 32 Isolated I/O Channels, 24V
APCIE-1500
-
The PCI-Express 32 digital I/O board APCIe-1500 has 32 digital inputs/outputs (24 V or 12 V), 14 inputs are interruptible. The 16 digital power outputs are equipped with protection diodes and filters. The board is fully compatible to the PCI board APCI-1500. It is especially suited for applications like industrial I/O control, signal switching, ON/OFF monitoring of motors, lights etc. in the harsh industrial environment. The APCIe-1500 has interruptible inputs. They supersede continuous cyclical query processes (polling) for routine monitoring and evaluation tasks. This takes load off the processor and the software. At a change of state of the digital inputs the APCIe-1500 generates an interrupt, so that the system reacts on the event through the interrupt routine and herewith fulfils real-time criteria.
