RF Attenuators
Used to reduce input RF & Microwave power by a fixed ratio – expressed in dB. (www.e-meca.com)
-
Product
Personal RF Detection Meters, High Frequency
-
Personal RF Detection Meters from Sensory Perspective Ltd
-
Product
Quad 4 to 1 50 600MHz PXI RF Multiplexer
40-760-004
Multiplexer Module
This 4 to 1 multiplexer is part of a range of RF multiplexers available in the following configurations: dual, quad and octal 4 to 1, single, dual and quad 8 to 1, single and dual 16 to 1 and single 32 to 1. All multiplexers have the option of automatic terminations which offer advantages at system level by reducing the presence of standing waves in the system which can cause degradation in isolation and crosstalk.
-
Product
RF Conducted Immunity Test System
RFCI61000-4-6
-
RFCI61000-4-6 RF Conducted Immunity Test System is an automatic test system which is for the conduction sensitivity testing, it is fully meets IEC61000-4-6.2006, ISO11452-4, GB/T17626.6-2008 and GTB152B-CS114 etc standards. RFCI61000-4-6 internal source and broadband power amplifier can be generated 3 voltage test levels: 1v, 3v and 10v, and has the function of the real detect output level. It has two operation software which is calibration software and test software. When measuring, the signal is in 1 KHZ sine wave amplitude modulation system (80%) to simulate the actual harassment, and can through the coupling/decoupling network (CDN or electromagnetic clamp) to make the harassment signal coupled to the device.
-
-
Product
PXI/PXIe RF Multiplexer, Single 4-Channel, 3GHz, 75Ω, SMB
42-832A-001
Multiplexer Module
The 40-832A-001 (PXI) and 42-832A-001 are 75 Ohm 4 to 1 RF multiplexers with 1 bank in a single slot. They have been designed to exhibit low insertion loss and VSWR through the use of modern RF relay technology at an affordable cost. Each MUX has been carefully designed to ensure excellent and repeatable RF characteristics to frequencies of 3GHz with each path having a nominally equal insertion loss. The design of the 40/42-832A minimizes the injection of noise and unwanted signals into the signal path by careful attention to the mechanical and electrical design.
-
Product
50 Ohm MCX to MCX Cable Assembly
40-977-561-1m
RF Cable Assembly
Pickering Interfaces offer a range of RF cable assemblies to complement our extensive range of PXI, LXI, PCI, VXI and GPIB switching products. All cable assemblies are made from high quality materials and use best practice assembly methods to ensure the cabling matches the performance of the switching modules they support.
-
Product
PXI 8x4 RF Matrix 100MHz 75 SMB
40-729-101
Matrix Switch Module
40-727/728/729 are RF Matrix Modules suitable for switching frequencies to 300MHz (50Ω version). The modules are available in either 50Ω or 75Ω versions with a choice of coaxial connectors. The 40-727/728/729 are designed designed to provide a simple and scalable bidirectional matrix to RF frequencies. They are intended for the easy construction of high performance bidirectional matrix switching systems.
-
Product
RF Shielded Enclosure, 80dB Isolation Testing
QuietBox-80c/r
-
The Raymond RF QuietBox-80c/r line of all-aluminum tabletop and rack mountable RF Shielded Cabinets offers effective RF isolation in a lightweight, fully-customizable package. Each QuietBox 80c/r is designed from the ground up to satisfy all the requirements of the client including enclosure dimensions, door swing and mounting style (tabletop or rack mount).
-
Product
Attenuator / Switch Driver
11713D
Attenuator
The 11713D attenuator / switch driver is a GPIB-compatible (LXI) instrument capable of driving both Keysight programmable attenuators and RF switches (electro-mechanical and solid state).
-
Product
Attenuators
-
Teledyne Microwave Solutions (TMS) offers a variety of analog controlled attenuators operating over a 10MHz to 26GHz range. With many units operating over many octaves, switching speeds less than 100nS and attenuation control up to 50dB, TMS has a product that meets your demanding needs.
-
Product
Optical & RF Switches
-
OPTELLENT is a provider of broadband test & measurement solutions for communications. OPTELLENT’s test and measurement solutions are designed to offer unprecedented low-cost of ownership and ease of use.
-
Product
Subminiature Coaxical RF Reed Relays
Series 102
-
Coaxial R.F. Relay. 50 Ohms Independence - Mu-metal SIL package or plastic flatpack. Flatpack - Up to 3 GHz
-
Product
Attenuation 100 High Voltage Passive Probe
-
Safe high voltage probe solutions for ground-referenced voltage testing. It is critical to safely and accurately capture real-time signal information from "elevated" or "floating" voltage systems.
-
Product
RF Safety Monitoring
MVG EME Guard XS 40GHz
-
EME Guard XS 40 GHz has been specifically designed to cover the new 5G millimeter wave bands. This RF safety tool is important for keeping those working close to RF emitters safer. It is easy to use, continuously scanning electromagnetic waves, and alerts the user when acceptable pre-selected limits have been exceeded.
-
Product
PXI/PXIe RF Multiplexer, Dual 8-Channel, 3GHz, 50Ω, SMB
42-874A-002
Multiplexer Module
The 40-874A-002 (PXI) and 42-874A-002 are 50 Ohm 8 to 1 RF multiplexers with 2 banks in a single slot. They have low insertion loss and VSWR through the use of modern RF relay technology at an affordable cost. Each MUX has been carefully designed to ensure excellent and repeatable RF characteristics to frequencies of 3GHz with each path having a nominally equal insertion loss.
-
Product
PXI/PXIe RF Multiplexer, Single 8-Channel, 3GHz, 50Ω, SMB
40-874A-001
Multiplexer Module
The 40-874A-001 (PXI) and 42-874A-001 (PXIe) are 50 Ohm 8 to 1 RF multiplexers with 1 bank in a single slot. They have low insertion loss and VSWR through the use of modern RF relay technology at an affordable cost. Each MUX has been carefully designed to ensure excellent and repeatable RF characteristics to frequencies of 3GHz with each path having a nominally equal insertion loss.
-
Product
RF Diagnostic Chamber
DST200
-
The R&S®DST200 RF diagnostic chamber is the ideal environment for RF analysis during development. It supports a wide range of radiated test applications for wireless devices and fits on any R&D lab bench, where it can be used at all times during the product design and optimization phase. The R&S®DST200 effectively assists in achieving high first-time pass rates during final type approval, which saves time and money.
-
Product
RF & Microwave PXI Switch Modules
-
These switching systems are used for design validation, reliability and production test including 5G, SD radios, S parameter testing for RF cables, antennas, radar and semiconductor verification.
-
Product
RF Matrix Switch for Wireless Technologies up to 4 GHz
NEXUS-4
-
Quintech Electronics and Communications Inc.
The NEXUS-4 is a bi-directional fully non-blocking 3232 RF matrix switching system that can route any input ports to any outputs in a 6 RU chassis. With the frequency range of 700 MHz to 4 GHz and the capability of expanding to 256256, it enables large scale wireless testing that involves many MIMO base stations and devices. The built-in programmable attenuators and efficient automation interface provide ease-of-use testing of signal fade and emulation of mobility scenarios. It can dramatically increase lab efficiency by eliminating manual patch panel and cabling as it can be remotely reconfigured for different test setups consistently in seconds.
-
Product
PXI/PXIe RF Multiplexer, Dual 8-Channel, 3GHz, 50Ω, MCX
40-874A-102
Multiplexer Module
The 40-874A-102 (PXI) and 42-874A-102 are 50 Ohm 8 to 1 RF multiplexers with 2 banks in a single slot. They have low insertion loss and VSWR through the use of modern RF relay technology at an affordable cost. Each MUX has been carefully designed to ensure excellent and repeatable RF characteristics to frequencies of 3GHz with each path having a nominally equal insertion loss.
-
Product
Digital Attenuator Operating Frequency of 1 to 20 GHz
LDA Series
-
The LDA series of Lab Brick® RF and Microwave Programmable Digital Attenuators includes 50 Ohm and 75 Ohm bidirectional RF step attenuators with calibrated operation up to 20 GHz. These USB powered and controlled units require no additional DC supply voltage. They are easily programmable for fixed attenuation or swept attenuation ramps directly from the included GUI. Lab Brick Digital Attenuator API DLL, Linux drivers and LabVIEW-compatible drivers are also available for custom programming applications.
-
Product
RF Voltmeter
9240
-
The 9240 series is the latest addition to Boonton’s popular 9200 series of RF voltmeters. It combines accuracy, smart probes, and operator features that have never before been available in its price range. It is simple to use on the bench, and comprehensive enough to integrate into an ATE system.
-
Product
WiFi / WiMAX RF Power Divider Combiners
-
INSTOCK Wireless Components, Inc
INSTOCK Wireless 2.4-6.0 GHz Power Divider, Power Combiners offer best-in-class performance for WiFi, WiMAX, 802.11b/g/n, and ISM signal splitting applications. IP67 outdoor weatherproof construction provides protection from the elements for uninterrupted outdoor use. All models available in 2-way thru 48-way configurations with Type N, SMA, TNC, BNC, and QMA connector configurations INSTOCK.
-
Product
PXI/PXIe RF Matrix, 8x2, 1GHz, 50Ω, SMA
42-750-521
Matrix Switch Module
The 40-750A-521 (PXI) and 42-750A-521 (PXIe) are 50 Ω 8x2 RF matrix modules with SMA connectors suitable for switching frequencies up to 1000 MHz. They are part of a range of 8x2 matrix modules with 50 Ω or 75 Ω characteristic impedance with front panel mounted SMA, SMB or MS-M multiway coaxial connectors.
-
Product
Attenuator Modules
-
The Analog Devices portfolio of wideband digital attenuators and voltage variable attenuators (VVAs) modules helps meet designers’ diverse needs. Low cost, high accuracy control, and small package options provide solutions for RF and IF applications, including the space, communications, and military industries.
-
Product
RF Switch Modules
-
Analog Devices RF switch modules include the highest bandwidth switch modules. SPST, SPDT, SP4T, SP6T, and SP8T versions (reflective and absorptive) are available for a wide range of power (up to 27 dBm) applications, including antenna switching, filter switching, and tuner applications.
-
Product
PXI 12x8 RF Matrix 250MHz 75 SMB
40-726A-751
Matrix Switch Module
The 40-726A is a 12x8 RF Matrix Module suitable for switching frequencies up to 300MHz (50Ω version). The 40-726A is available in either 50Ω or 75Ω versions with a choice of coaxial connectors. The module is designed to provide a simple and scalable bidirectional matrix for RF frequencies. Isolation Switches are located on all coaxial connectors, these disconnect the matrix from the external test fixture. This maximizes isolation and RF performance.
-
Product
LTE RF Communication Subsystem
-
The Delaire USA LTE RF Communication Subsystem is designed to provide a versatile solution for the testing needs of the next generation wireless systems. With the LTE test subsystem developers can build an end-to-end test environment for complete system operation. From end user equipment and eNodeB base stations to full system functionality, the LTE RF Communication subsystem allows developers to test and evaluate equipment and system performance in a controlled laboratory environment.
-
Product
Parallel Testing of Multiple DUTs with High RF Channel Count
Test Rack UTP 7033 RF for validation
-
Our basic test rack UTP 7033 (33 rack units) is intended for equipping with various products and therefore for various application areas.The rack shown here as an example is prepared with products and measurement instruments to test automotive devices with high channel count.
-
Product
RF Acquisition Record and Playback Instrument
SARP-6
-
Saluki SARP-6 RF Signal Acquisition Record and Playback Apparatus is a portable RF signal acquisition record playback equipment. It can be used to directly acquire, record, and playback RF signal from 1MHz to 6GHz. Its data recording and bandwidth playback can reach 200MHz. The SARP-6 RF Signal Acquisition Record and Playback system is composed of up and down inverter module, high-performance ADC and DAC, and large capacity solid-state FLASH or high-performance disk. It is widely used in radar, GPS, communication, telemetry, as well as many other circumstances for civil purposes when acquiring signal and recording it down.Applications: Interference Analysis/Surveillance/Spectrum Management/Satellite Communications
