EV Testers
See Also: EV Test Systems
-
Product
Combination Board Tester
-
Qmax Test Technologies Pvt. Ltd.
Combination Board Tester capable of testing highly complex and dense PCBs employing various test techniques on a single platform. It can perform Board Level Functional Test through edge connectors of a PCB, and guided probe diagnostics utility to reliably repair Digital/Analog and Mixed Signal PCBs of various complexities and conventional PCBs. An In –Circuit device test by configuring Pin Drivers to High Current Pin Driver mode and interface to the UUT either through Clips / Probes or nail bed and on board clock disable HW feature are the all time favorite . The in-built high frequency 14bit Analog Driver / sensors synchronized with digital drivers for covering analog / mixed signal devices with high degree of accuracy.
-
Product
Ground & Wrist Strap & Footwear Tester
-
Dou Yee Enterprises (S) Pte Ltd
Dou Yee Enterprises Ground & Wrist Strap & Footwear Tester
-
Product
Public Switch Telephone Network Tester
295B
-
The Testphone 295B is a test telephone designed for use on Public Switched Telephone Networks (PSTN). It is designed for use on both Dual-tone Multi-frequency (DTMF - tone dialling) and Loop Disconnect (LD - pulse dialling) lines. Fitted with an integral ADSL filter, the telephone will not cause interference when connected to ADSL/Broadband lines in either `on hook` or `off hook` mode.
-
Product
Crease Recovery Tester
TF110
-
TESTEX Testing Equipment Systems Ltd.
Crease Recovery Tester, to determining recovery properties of fabrics by creasing in a loading device for a predetermined time using a weight suitable for the test method specified (BS/ISO/AATCC), After transferring the specimen to the clamp of the tester, the specimen is allowed to recover and the angle of recovery recorded. Fabric Crease Tester complies with ISO 2313, AATCC 66, BS EN 22313， etc.
-
Product
Rainproof Tester
TF161
-
TESTEX Testing Equipment Systems Ltd.
Rainproof Tester, to determine the penetration resistance of fabrics or composites at different intensities of water impact. Simulated rain horizontally impacts fabric samples mounted vertically in a stainless steel bath. Samples are backed with a standardized blotting paper, which is weighed before and after each test. The rain is formed by a column of water, which can be adjusted from 600mm to 2400mm.
-
Product
Paper Softness Tester ZRD-T1
-
The ZRD-T1 Paper Softness Tester is a device designed to objectively measure the softness of paper products, such as tissues, toilet paper, or specialty papers. Softness is a complex tactile property influenced by factors like surface smoothness, flexibility, and bulk compressibility. It is widely used in industries such as tissue manufacturing, hygiene product development, textiles, and packaging to ensure compliance with quality standards and end-user comfort requirements. This test instrument conforms to many national and international standards: ASTM D2923: Standard Test Method for Rigidity of Paper – Measures bending resistance to determine stiffness. ASTM D6828: Standard Test Method for Stiffness of Nonwoven Fabrics – Evaluates drape and flexibility in materials like medical textiles or wipes. TAPPI T498: Bending Resistance of Paper (Gurley Method) – Quantifies resistance to bending forces, inversely related to softness. GB/T 8942: Chinese Standard for Softness Testing of Household Paper – Aligns with consumer expectations for tissue and toilet paper tactile quality. ISO 12625-9: Softness Evaluation of Tissue Products (optional add-on).
-
Product
0-5KV Digital Hi-pot Tester 0-5KV
7110
-
Shenzhen Chuangxin Instruments Co., Ltd.
Programmable AC/DC withstand voltage tester Feature: Small volume, light weight Easy to operate, has keyboard lock function Provide 5 groups memory setting, each group has four kinds of work mode
-
Product
Buss Interface Unit Tester
BIUT 820
-
Quickly and reliably check any BIU with the BIUT-820 which provides comprehensive, fully automated testing in the field or at the shop.
-
-
Product
Press-type Vibration Tester
9363-PC-ESS
-
King Design Industrial Co., Ltd.
This machine complies with the IEC, JIS and other 5-100Hz low-frequency specifications; applied to test the post-assembly products at end of the production line. Use resonance amplification, the product’s flaws can be screened out in advance. The operation is convenient, fast and effective.Apply Japan-imported motor; durable and safe in operation.Bellow-type damper: use special damping material that can effectively absorb vibration; allowing the test to be performed without affecting floor structure.Motor drive system is embedded in the seat; good in vibration block-out; rigidity is strong. Follow specimen to design fixture.
-
Product
Battery Cell Tester
-
This Centre zero instruments help to read the voltage irrespective of polarity.
-
Product
Digital ELCB (RCD) Tester
2712 EL
-
Standard Electric Works Co., Ltd
● Microprocessor-controlled.● 2 Lines × 16 characters LCD.● Very low consumption.● 50Hz and 60Hz operation.● Menu-driven.● Accurate digital readout of disconnection time.● Automatic data hold function.● Over temperature protection.● Over voltage protection.● Fuse protection.● Zero crossing circuitry permit testing at 0° or 180°.● Disconnection phase polarity shown on LCD display.● Auto off and off override.● Polarity trip indicator (positive or negative phase)● Wiring polarity indicator.● Measure voltage between Line and Earth before testing.● Frequency measurement indication.
-
Product
Hose Continuity Tester
OhmGuard
-
The OhmGuard hose continuity tester is designed to test hoses used on vacuum trucks and tanker trucks prior to the transfer of flammable or combustible products
-
Product
IEC60065 Fig11 Australia UL Plug Socket Tester Socket Outlet Torque Tester
CX-CTN
-
Shenzhen Chuangxin Instruments Co., Ltd.
The plug torque tester conforms to the standard of IEC60065 figure 11. It is used for checking whether the mechanical stress which occurs when the Direct Plug-in Equipment with plug pin normally insert into the socket is in the required range.
-
Product
Waterproof Eco Tester EC Low
EcoTestr EC Low
-
The Eutech EcoTestr EC series comes with rugged, sturdy stainless steel pin sensors, giving you quick, reliable conductivity measurements. Ideal for use in a wide range of conductivity applications, such as hydroponics gardening, fish-farming, pools, electroplating and other water/ wastewater applications.
-
Product
Low Voltage Harness Tester
CR
-
Test complex assemblies with thousands of points. The system supports guided assembly with on-screen connector images, guidance LEDs on the assembly board, and immediate graphical and audible feedback to catch errors as they occur.
-
Product
Bonding Tester
PTR1102
-
In wire bonding in semiconductor manufacturing, electrodes are joined using gold wires of several tens of microns. In order to measure the pull (tensile) strength and ball shear (shear) strength of this gold wire, this machine has load detection accuracy and fine positioning accuracy. In addition, for the measurement of high load areas such as die shear strength and solder joint strength, this machine supports measurement in high load areas while maintaining accuracy in low load areas by replacing the sensor part.
-
Product
Water Vapor Absorption Tester
DRK854A
-
Shandong Drick Instruments Co., Ltd.
Used to test the water vapor absorption performance of the sample.
-
Product
Buchholz Hardness Tester
3095
-
Measuring a coating’s hardness using the indentation method, the Elcometer 3095 Buchholz Hardness Tester consists of a bevelled disc indenting tool that is fitted into a stainless steel block exerting a constant test load of 500g (17.6oz).
-
Product
Compact Tablet Hardness Tester
HC 7
-
The new member of our Lab.line product family: the HC 7 hardness tester for manual use in the laboratory.Equipped with a touch display and the new database-driven touch software, the HC 7 impresses with its exceptional user-friendliness. The new software can be operated intuitively and is equipped with all important functions for quick operation.Start your quick, direct and product testing with just a few clicks directly via the touch display and set up to 50 products. Reports can be printed externally via USB or LAN interface. It is also possible to connect DYMO* and EPSON* roll printers (*special models only).
-
Product
Advanced Cable Tester v2
TP800110
-
The Total Phase Advanced Cable Tester v2 is the quickest and most convenient way to comprehensively test USB, Lightning, and video cables. It provides:*Short testing - Dynamic visualization of test results*Open testing - Dynamic visualization of test results*Continuity testing - Dynamic visualization of test results*DC resistance measurement for most wires, with milliohm precision on ground and power wires, ohm resolution on most other wires, continuity check only on high-speed data lines*Signal integrity testing of data lines to 12.8 Gbps per channel*E-Marker verification*Lightning plug bring up/function (Apple Lightning Cables)**Over-voltage protection (Apple Lightning Cables)**Voltage recovery testing (Apple Lightning Cables)**Quiescent current consumption (Apple Lightning Cables)*
-
Product
Combination Board Tester
ATE QT2256-640 PXI
-
Qmax Test Technologies Pvt. Ltd.
Most commercial ATEs does only functional test and do not carry out DC/AC parameter testing, which are very essential in increasing the fault coverage and for achieving near zero field returns. The testing challenges get worse when the boards are equipped with BS compatible components, DSP chips and CPUs or micro controller based boards. ATE QT2256-640 PXI system is designed as a combination board tester capable of testing highly complex and PCBs employing various techniques on a single platform. It can be easily upgraded to 640 digital channels and with programmable UUT power supplies, IEEE or PXI external instrumentation, Bus cycle signature system, ICE and integrated Boundary scan Test AC/DC parametric testing. The ATE is interfaced to an external host PC using a PCI express interface card allowing a maximum data transfer rate. Most commercial ATEs does only functional test and do not carry out DC/AC parameter testing, which are very essential in increasing the fault coverage and for achieving near zero field returns. The testing challenges get worse when the boards are equipped with BS compatible components, DSP chips and CPUs or microcontroller based boards.
-
Product
DMX Tester
DXT1
-
The new DMX Tester from NuDelta Digital is a feature-packed test tool you won't want to leave home without. It can send any level to any DMX address with simple commands similar to those found on the world's most popular lighting consoles. It can test for valid DMX signal and show you the level at any address. It can test continuity on all five pins of a standard DMX cable and indicate which pins are not connected or cross-wired. Runs for hours on a 9 volt battery (included).
-
Product
Impulse Winding Tester
TH2883-1
-
Changzhou Tonghui Electronic Co., Ltd.
TH2883 series products are newly developed impulse winding testers by Tonghui. This product line makes Tonghui as the first provider of impulse winding tester from low voltage of 30V to high voltage of 10kV, single channel to multichannel (Max.:8 channels) in this industry. The instrument adopts popular 32 bit CPU and high density SMD technology, 65k color 7-inch TFT wide display screen, bringing ease for your eyes and convenience to your operation. The minimum impulse voltage of 30V, maximum impulse voltage output of 10kV, winding test of 1uH inductance value, sampling rate of 200Msps, memory depth of 6k bytes makes your test accurately. The usage of standard sample average, application of demagnetized impulse, high bandwidth analog acquisition circuit, technology of high-fidelity corona extraction as well as the opening of non-destructive test reflect the design philosophy “customer-oriented, share the future technology with you” of Tonghui.
-
Product
PD (Partial Discharge) Tester
-
Weshine Electric Manufacturing Co., Ltd
Using the Windows system operating platform, you can freely choose ellipse, straight line, sine wave display, two-dimensional, three-dimensional graphic analysis mode, spectrum window, Q-V-F three-dimensional characteristic window, and static detailed measurement, observation and analysis of partial discharge pulse of one-cycle test voltage .
-
Product
Axis Play Tester
LMS 20.0 | VP 425017
-
Maschinenbau Haldenwang GmbH & Co. KG.
The LMS 20.0 axis play tester is used to reliably determine defects and wear on steering parts, wheel bearings, suspension and suspension by means of counter-rotating transverse and longitudinal movement of the test plates. The built-in hydraulic drive ensures a powerful and even movement of the test plates. An automatic mode and other different operating modes make the LMS 20.0 easy to use.
-
Product
Smart Card Testers
CT1000
-
The CT1000 testers are open and configurable to test any kind of communication protocols used on smart cards, and to be updated for new technologies. The systems can test devices that use common standard protocols (as ISO 18000, EPC Global Gen 2, ISO 14443, ISO 15693, MIFARE™, DESFIRE™, FeliCa™, ISO 11784/85, ICode™, Hitag™, ISO 7816, ISO 7813), and are ready to test also the next generation of cards protocols, such as: USB-Keys, MMC, Micro-SD (with and without CPU inside), M-SIM, HD-SIM, SIM-WAVE, and I2C.
-
Product
Hardness Testers
-
Dalian Taijia Technology Co.,Ltd
Digital durometer for shore hardness testing pocket size model with integrated probe● Test scale: shore hardness● Standards: DIN53505, ASTMD2240, ISO7619, JISK7215● Parameters displayed: hardness result, average value, max. value● Measurement range:0-100HA(HD)(HC)● Measurement deviation:＜1%H● Resolution: 0.1● Auto switch off● With RS232C interface● Operating conditions: 0℃ to 40℃● Power supply: 4x1.5V AAA (UM-4) battery● Battery indicator: low battery indicator● Dimensions: 162x65x38mm● Weight (not including probe):173g● Application:Shore A is designed to measure the penetration hardness of rubber, elastomers and other rubber like substances such as neoprene, silicone, and vinyl. It can also be used for soft plastics, felt, leather and similar materials.Shore D is designed for plastics, Formica, Epoxies and Plexiglass.shore C is designed for various foam and sponge.
-
Product
PARASITIC DRAW TESTER
MD649
-
*Provides an easy way to connect a multimeter to a vehicle's electrical system to diagnose hidden battery drain*In-line fuses protect both the meter and the tester in the event a high current source on the vehicle is left on*Tester and meter can remain connected until other computer systems shut down, isolating the drain
-
Product
130 AMP Battery Load Tester
MD4370
-
Compact, ergonomically designed tester determines a battery's charge and tests batteries, starting, and charging systems.Powerful 130 amp load capacity provides more accurate test results.Uniquely designed clamps assure a positive connection on any style battery.
