Solar
energy of the sun's rays.
-
product
Detectors
Solar blind detector for operation in the 1 to 180 nanometer region. It is encased in a vacuum tight housing for vacuum operation. The Model 425 is ideal for measurements in the Extreme and Vacuum UV (EUV and VUV) where the solar blind feature eliminates potential interference from long wavelength ultraviolet and visible light. It may be operated in pulse-counting mode or DC. The CEM is also available with coatings like Cesium Iodide or Magnesium Fluoride to enhance response in different energy regions.
-
product
Solar Array Simulator DC Module, 65V, 8.5A, 510W
E4361A
The Keysight E4361A is a 510W solar array simulator DC power module that simulates the output characteristics of a solar array. The E4361A is primarily a current source with very low output capacitance. It offers fast I-V curve changes allowing you to accurately simulate the output of different solar arrays under various environmental conditions (ex. temperature, age, eclipse, spin etc.). The E4360 gives you the flexibility to operate it in two ways:
-
product
Solar Stimulator
XHS Series
They are mainly used for the evaluation of solar cells as well as for other types of tests where sunlight needs to be recreated.The continuous light of xenon lamp, the most faithful reproduction of sunlight, is applied in our highly accurate solar simulator, which has been widely sold across Japan and neighboring countries.
-
product
Environmental (Radiation) Monitoring System
Hawk® EMS
The Hawk® EMS is a wall or tripod-mounted radiation monitoring and alarm system designed for use with the Hawk® Radius dual sensor radiation probe. Each EMS System comes with a Hawk Radius Probe. The system is extremely energy efficient and can run for weeks on an internal 9 volt back-up battery if power fails. It is well suited for operating on a small solar panel, which is an optional accessory. The Hawk® EMS features two displays that show the radiation levels measured by each of the probe’s two detectors: the weatherized “pancake-style” Geiger-Mueller tube — which measures alpha (if configured for it), beta, low energy gamma, and x-radiation — and the energy-compensated gamma tube which measures penetrating gamma dose rate. The probe can be mounted next to the EMS system or outdoors, or in adjacent rooms on cables up to 100 ft in length. Standard cable is 3 meters in length. Optional signal booster can support cable lengths longer than 100 feet. Optionally the system can also be configured to share data on ethernet or wireless networks.
-
product
Current-Voltage Measurement System
Sciencetech''s IV Testers are electrical current-voltage measurement systems used to characterize photovoltaic cell performance. This current-voltage tester works by sampling various current versus voltage combinations of the photovoltaic cell with a variable impedence load.This IV Test system can measure electrical power from photovoltaic cells up to 20W. The voltage envelope is limited to 20V and the current to 1A. A higher power version, up to 60W, is available. In general, the limitation on this model is the 1A current limit: if your solar cell generates more than 1A, we recommend upgrading to the 60W version.
-
product
COMETEO Multi-Plate Radiation Shield
F8100
Newly developed meteorological screen for humidity and temperature transmitters. Passive solar radiation and weather shelter for meteo sensors.
-
product
Solar Simulator Testing Kits
Solar Light’s Solar Simulator Testing Kits are designed for scientific and industrial professionals who want everything they need to begin testing all in one comprehensive package.
-
product
Environmental Testers
When you’ve got a specialized job to do, general-purpose tools won’t do. Whether you’re measuring sound, light, water or solar energy, depend on Amprobe for affordable, environmental test solutions.
-
product
6″ (15.25 cm) 1000W Pre-Irradiation Solar Simulator
Model LS1000-6S-009
1000W Pre-Irradiation Solar Simulator Kit specifically designed for the pre-irradiation step during in vitro broad spectrum sunscreen testing. Fully compliant with the most current FDA and ISO requirements. The 6″ (15.25 cm) Class A beam can irradiate up to 9 PMMA plates simultaneously.
-
product
Solar Simulator
It is an LED light source for evaluating the performance of organic solar cells in indoor light applications.A neutral white LED light source equivalent to a color temperature of 5000 K, achieving an effective irradiation area of 50 × 50 mm.The illuminance can be changed without changing the height of the light emitting surface with low illuminance (200 lx) and high illuminance (1000 lx).
-
product
OPV/DSC/Perovskite IV measurement System
King Design Industrial Co., Ltd.
The system can measurement the 3rd generation of solar cell IV performance. The system patent with eliminate capacity effect that can ensure the test repeatability coincidence.
-
product
DC Laboratory Power Sullies
Elektro-Automatik GmbH & Co.KG
Adjustable, programmable, 19” 3U rack-mount formatGorilla glass TFT touch display, versatile function generator, user profiles, resistance regulation, solar (PV) simulation, fuel-cell (FC) simulationAuto-ranging outputOn board 2-way interface (USB/analogue), Plug N’ Play slot for retrofitting additional interfaces such as Ethernet, CAN, CANopen, Profibus, Profinet, RS232 and moreVoltages 0-60V up to 0-1500VDCCurrents 0-20A up to 0-510A Powers 5kW up to 15kW
-
product
Solar Simulator Continuous Light
This type of solar simulator uses Xenon high pressure arc lamps as light source. These lamps have a colour temperature near 5800 K, so it is feasible to filter the light output to an excellent AM 1.5 spectrum. If a tuneability of the spectrum is required, these lamps can be combined with tungsten lamps to achieve multi-source solar simulators. These can be used to measure tandem/triple/multijunction solar cells. They also allow detailed analysis of all types of solar cells using a spectral metric (see : Publication List).
-
product
Electronic Loads
PeakTech Prüf- und Messtechnik GmbH
Can be used for important test procedures in quality assurance as well as e.g. testing of power supplies and control units, batteries, fuel and solar cells. For precise load control for various purposes, this device offers load control according to constant voltage (CV), constant current (CC), constant load resistance (CR) or constant power (CP) with a highly precise resolution of 1mW, 1mV, 1mΩ and 1mA. The device also offers additional test modes, e.g. the battery test or the dynamic test. The PC interface and software offer the option of implementing freely programmable test sequences with data evaluation.
-
product
High Power DC Electronic Load
M97XX series
The new M97XX series programmable DC electronic load is a new generation product designed from Maynuo Electronic Co.,Ltd. Incorporating high-performance chips, the M97XX series delivers high speed and high accuracy with a resolution of 0.1 mV and 0.01 mA (basic accuracy is 0.03% and basic current rise speed is 2.5 A/μs). M97XX series have wide application from production lines for cell phone chargers, cell phone batteries, electronic vehicle batteries, switching power supplies, linear power supplies, and LED drivers, to research institute, automotive electronic, aeronautic and astronautic, maritime, solar celland fuel cell etc.test and measurement applications.
-
product
Pyranometers Spectrally Flat Class A
LPPYRA10… Series
The pyranometers LPPYRA10 measure the irradiance on a flat surface (Watt/m²). Range 0-2000W/m² or 0-4000W/m². The radiation measured is the sum of direct solar irradiance and diffuse irradiance (global radiation).
-
-
product
TriSOL Large Area Solar Simulators
OAI has designed and engineered for large area markets Class AAA, ABA, or ACA Solar simulators with the same performance , quality, and reliability as our other solar simulator models. These large area solar simulators are available in several models.
-
product
Digital Panel Meter
VAW
VAW DC Multifunction Power Meter provide high accuracy measurement, display and communication of DC voltage, Current, Power, Energy(import / export), and Run Hour. They are also building in 4 Relay outputs, 1 Analogue output, 1 Pulse output , 2External Control Inputs and 1 RS485(Modbus RTU Mode) interface with versatile functions such as remote I/O, alarm and communication for DC power applications like as solar, wind power system or portable electronic device consumption testing.For the power saving, VAW has built in an innovation timer to switch down the light and power of LED. It makes sense to build the meter in a green power system.
-
product
TRUE RMS High Voltage DMM
8000 HVDM
Standard Electric Works Co., Ltd
● True RMS measurement● For measuring solar, PV systems● Auto ranging● Bar-graph indication● Data hold function● 3000V DC Voltage measurement● 2000V AC Voltage measurement● AC mA/uA measurement● DC mA/uA measurement● Low battery indication ● Auto power off ● Low power consumption● Rugged and compact● Comply with IEC / EN 61010-1, CAT III 1000V IEC / EN 61010-1, CAT IV 600V● Comply with CAT III 1000V for the range of 0~1000V AC/DC
-
product
Pyranometer with Silicon Photodiode
LP471SILICONPYRA
Pyranometer with silicon photodiade for GLOBAL SOLAR IRRADIANCE measurement.
-
product
License For Automated EN50530 Static And Dynamic MPPT Efficiency Testing
DG8901A
Optional upgrade for Solar Array Simulator (SAS) app. Provides additional automated static and dynamic EN50530 maximum peak power tracking (MPPT) tests.
-
product
Stand-alone I-V Test Systems
OAI offers a complete line of high performance I -V Testers. I -V Testers and I -V Rider software may be ordered as a stand -alone system or integrated into any OAI Solar Simulator. Three standard ranges of I -V Testers are available; ≤1A, 1 -5A, 5 -10A, and 20A. Higher current testers are available as custom options. An OAI Application Engineer will work with you to insure that the I -V Tester and I -V Rider software you choose is optimized for your specific application.
-
product
Laser Distance Measurer
NT-8580
Ideal for measuring factory layout, facilities safety area, trench depth, roof area for solar, building maintenance, ceilings maintenance, road works, water level, sheet rock measurement.
-
product
Calibrated Solar Reference Cell
To insure repeatable testing on any solar simulator, OAI offers 2cm x 2cm calibrated reference cells. Standard reference cell calibration cycles can be set up by OAI''s calibration laboratory to insure that your reference cell maintains certification.
-
product
High voltage Flexible range Regulated DC Power Supplies
PSF-H Series
* Main Applications: High-voltage capacitors or relays used for hybrid cars, electric cars, solar power system and high-voltage LED lighting equipment.* 6 times of flexible output range: PSF-800H covers output for several units of conventional type regulated power supplies within 800W ( max voltage 800V, max current 6A. ).* Constant Power Control: CP mode is available in addition to CV and CC modes.* Changeable setting style: Vertical or horizontal setting by 90rotating panel.* Sequence Operation: Stand-alone sequence is available with the insidememory programmed by PC, through the optional control board (IF-60GP, IF-60RU).* Master-slave parallel operation: Possible to increase the output current by master-slave parallel connection of the same model (up to 2 units).* Various functions are available: Output OFF timer, 3-point preset memory, Remote sensing, External analog control, OVP/OCP/OHP protections
-
product
Contact Probe for Solar Panels
TP878.3
Contact temperature probe for solar panel. Class B Pt100 sensor. Adhesive aluminum plate. Dimensions 10 x 30 x 5 mm.
-
product
Surface Photovoltage
The surface photovoltage spectroscopy modules are the perfect all-in-one solution for in-depth studies of light sensitive materials such as organic semiconductors, solar cells or light sensitive dyes.
-
product
Solar Power Meters
TES Electrical Electronic Corp.
Wide spectral range. Excellent long term stability.Cosine corrected. Automatic transmission measurements. Select either power or transmission. Solar energy measurement.
-
product
Datapaq Solar Tracker System
The SolarPaq® Thermal Profiling Systems from Fluke Process Instruments are designed specifically for solar photovoltaic (PV) manufacturing including applications like contact firing, contact drying, anti-reflection coating for the solar cell, lamination and other thin film processes. These systems, consisting of user-friendly Insight™ software, Datapaq® Q18 data loggers, stainless steel thermal barriers, thermocouples with PTFE or mineral insulation and accessories, provide users with the tools needed to gather accurate, repeatable results for process optimization, maximize cell efficiency and throughput, and more.
