- Virginia Panel Corporation
product
Coax, Contact, ITA, 20 GHz, RG 223, Crimp, 90 Series Modules only
610102117
Primary mating contact 610102116. (May mate with other ITA contacts, as well.)20 GHz coax contacts have an impedance of 50 Ohms and a current rating of 5 amps.It is recommended to use SF142 to achieve 20 GHz and RG223 to achieve 12 GHz.Mechanical SpecificationsDurability 20,000 cyclesContact Material Shield – BrassCenter Conductor – BeCuContact Plating 30µ" Au over 100µ" NiContact Termination Shield – Crimp/ClampInsulator PTFEMating Force 3.0 lbs max [1.36 kg]Electrical SpecificationsChara...show more -
product
cPCI 6U DC 350W
Hartmann’s cPCI Power Supplies comply with PICMIG and offer a wide range AC input. These supplies are developed and produced with quality and durability in mind, at a price that won’t bankrupt your project. Talk to a Hartmann representative today about your power needs!
-
product
SCR Controlled DC power Supplies
Variable DC power supplies are AC to DC power supplies with a variable DC output. The output can be varied with an SCR controller. The AC input power can be single-phase or three phases. With single-phase AC input, the DC output ripple is very high (50%). With three-phase AC input, the DC output ripple is low (5%). This would be a key benefit for selecting three-phase AC input instead of a single phase.
-
product
Through Hole type DC Current Sensor／for Load Current Measurements
MOHT-200B Open loop method
MULTI MEASURING INSTRUMENTS Co., Ltd.
*Hall effect measurement for DC/AC/Pulsed current.*For the use of UPS, batteries, switching power supply, DC motor drivers, etc.
-
product
Suitable For Current Or Voltage Process Signals
SEM1600VI
The SEM1600VI is a “smart” powered isolator/conditioner that accepts any voltage signal between (-50 and 50) V dc or any current signal between (-50 and 50) mA
-
product
Digital Recorder
HiRES
HIGHVOLT Prüftechnik Dresden GmbH
The digital recorders HiRES are used to measure, store, and evaluate signals from up to 64 sources synchronously. Depending on the sensors used voltages, currents, temperatures, mechanical movements and various other signals can be measured. This measurement system features the ability to capture fast transient processes such as those occurring in impulse current tests on electrical devices or during switchgear testing. The system is also capable of measuring semistationary and periodic events such as DC voltage and AC voltage as well as superimposed semistationary, periodic and transient processes.
-
product
Base Model Custom Configured Modular Power System
N6710C
The Keysight N6710C is a 400 W build-to-order system that is shipped as a fully tested and assembled multiple-output power supply. Each N6710C consists of 1 N6700C mainframe and from 1 to 4 DC power modules. Modules are ordered as options to the N6710C.
-
product
DC Resistance Tester
DCSS502BC
Resistance meter is designed to measure copper resistance of transformers, wires, cables, other conductors and other coil products etc. It is widely used of low resistance measurement of switches, heater wires, transformers, relays, motors, electric films and PC circuit boards, wires, cables, etc. With reliable Good/ NG judgement, it is a premier resistance meter for the use in production line or QC department.
-
product
VME PWM Servo Motor Driver / Amplifier Board
64PW2
NAI’s 64PW2 is a 6U VME Servo Motor Driver/Amplifier Board featuring a dual, four-quadrant, bi-directional, PWM servo amplifier. Specifically targeted for DC servo motor applications, this board has an amplified power stage that uses a Pulse Width Modulation (PWM) control signal to provide motor control for both brush and brushless motors. Each motor drive accepts a 65 VDC power input and provides a 5 Amp maximum continuous current output (8.5 Amp peak).
-
product
Vibration Unit Tester
BK2020B
We developed the BK2020B as an upgrade to our BK2020 to test the electrical specifications (RPM, current, drop pulse, start up voltage) of your cylindrical or coin type vibration units. You can also test vibration level, noise, isolation resistance, and the DC resistance. The DUT power supply and all measurement components are self contained, so external devices aren't needed and the tester uses DSP, making it capable of fast, highly accurate and reliable measurements. The BK2020B is very versat...show more -
product
LED Testers
PeakTech Prüf- und Messtechnik GmbH
An extremely practical component tester for LEDs and other components. The device outputs an automatically raised output voltage between 0 to 300 V DC, which adapts to the connected load so that the sensitive components are not destroyed. Particularly suitable for the service and repair workshop.
-
product
Closed Loop Hall Effect Current Sensors/Transducers
ChenYang Technologies GmbH & Co. KG
This Hall Effect current sensor is based on closed loop compensating principle and can be used for measurement of DC and AC current, pulse currents etc. The output of the transducer reflects the real wave of the current carrying conductor
-
product
Standard 1.00 (28.00) - 3.20 (91.00) General Purpose Probe
P2250-9
Current Rating (Amps): 5Average DC Resistance lower than (mOhm): 30Test Center (mil): 187Test Center (mm): 4.75Full Travel (mil): 250Full Travel (mm): 6.35Recommended Travel (mil): 167Recommended Travel (mm): 4.24Overall Length (mil): 1,453Overall Length (mm): 36.91Rec. Mounting Hole Size (mil): 126Rec. Mounting Hole Size (mm): 3.20Recommended Drill Size: #30 or 3.20 mm
-
product
Digital Circuit Tester 3-49V
28830
Operating range of 3-49 volts DC to work on most vehicle electrical systems. 360° visibility of polarity. The red light indicates positive polarity, green indicates negative polarity. Long, 12ft. coil cord and heavy-duty alligator clamp for secure connections. The probe is insulated to prevent the possibility of shorting the side of the probe to other components.
-
product
Director's LCD Monitor with Wireless RF Link
EZ-ROAM D
The highly portable "EZ-ROAM D" has been designed for life on the road, and is ruggedly constructed in an extruded aluminium case sealed to IP67, and tough enough to take every day knocks and bumps. Battery powered (and with an external dc input too), the EZ-ROAM D with it's 7" LCD provides robust diversity radio reception, whilst the recessed controls offer selection between video inputs, 16:9 or 4:3 aspect ratios, Horizontal & Vertical flip, and stereo audio monitoring. There is even an RX OP on BNC.
-
product
DC Voltage Generator
MON8P
Mezzanine MON8P is designed to generate DC voltage in the range of ± 10 V through eight galvanically isolated channels from each other and from the case, which allows to reduce the level of interference and increase the safety of the device.
-
product
High 1.80 (51.00) - 12.60 (357.00) Switch Probe
TSP138-C180-3
Current Rating (Amps): 10Average DC Resistance lower than (mOhm): 20Test Center (mil): 138Test Center (mm): 3.50Full Travel (mil): 197Full Travel (mm): 5.00Recommended Travel (mil): 157Recommended Travel (mm): 4.00Overall Length (mil): 1,760Overall Length (mm): 44.70Switch Point (mil): 67Switch Point (mm): 1.70
-
product
Bias Tees
Mini-Circuits is your complete source for bias tees, handling up to 4 Amps DC and covering 100 kHz to 12 GHz!Rugged coaxial modelsTiny surface mount packages as small as 0.15 x 0.15 inExcellent isolation50 and 75 Ohm models
-
product
Hi-Speed Discrete Test System
QT-6000
QT-6000 Test System, with built-in capacitance test (DC+CAP) and Scanbox etc, is applicable to devices like medium & small power transistors, MOS-FET, diodes and Wafer.
-
product
- Optically Isolated Line Driver
Model 72A
FEATURES: DC TO 19.2 KBPS; Optically Isolated; TD & RD LED's; Loopback Switch; Built-In Surge Protection; Male or Female Connectors; Screw Terminals and RJ-11. The Model 72A Optically Isolated Line Driver links RS-232 based devices over extended distances. It provides optical isolation and has built-in verification of operation using a loopback switch.
-
product
Impedance Analyzer 10MHz-20Hz
IA1021
Feature Specifications: Dual test mode: Analyzer(frequency sweep) and LCR(single frequency).Measurement frequency: 20Hz to 10MHz, 6 digitsFrequency resolution: 0.001% in all frequency rangeFrequency accuracy: 0.01%.DC bias(program): -10V ~ +10V, 0.005V resolution, accuracy 0.5%.Measurement basic accuracy: Impedance +-0.2%, phase: +-0.1°.Display Range: Z: 0.0000Ω-99.999MΩ.
-
product
Digital Control DC Electronic Load
IT8200 Series
IT8200 series economical programmable electronic load,with the highest cost/performance ratio and small size, they are widely used in production testing lines and maintainance lines etc. Resolution 1mV/1mA ensures the accurate measurement result. IT8200 series has programmable performance, and can quickly recall 4 * 40 group memory data, panel function keys and display interface is clear, provide customers with simple operation program, easy and fast to complete a variety of complex tests. The series has CV, CC and CR mode, and short circuit test function, it is the most cost-effective electronic load products.
-
product
20dB In-Line Amplifier
HSA-20
Hangzhou Huatai Optic Tech. Co., Ltd.
*Excellent Zinc die-casting chassis, with good shielding feature. *All ports can be passed by DC. *Output ports are F-British system, impedance 75Ω.* Perfect technique of superficial treatment guarantees frequency respondence.
-
product
DC - 12 GHz Packaged High Efficiency Divide by 8 Prescaler
HMMC-3128-BLK
TheHMMC-3128-BLK is a packaged DC - 12 GHz divide by eight prescaler designed for use in high frequency communications, microwave instrumentation, and EW radar systems where low phase-noise PLL control circuitry or broadband frequency translation is required.
-
product
Analog Multimeter
KF-23
12A DC measurement.Easy-to-read scale plate with meter mirror.Gold-plated test leads.LED test and 1.5V battery test.Decibel measurement available.
-
product
Capacitor for DC Filtering
FIL2
Lifasa - International Capacitors, SA
FIL condensers are specially designed for use in direct current sources and their functions are to filter the alternating output ripple as well as protect the line from momentary spikes and sudden power surges.
-
product
True RMS Clamp Meter
DL489
UEi Test & Measurement Instruments
The DL489 True RMS Clamp meter offers contractors better features, functions and safety in a commemorative edition housing. A complete meter with the precision of True RMS and the functionality your job requires. Featuring 600A AC/DC, 750V AC and 1000V DC, resistance, capacitance, diode test, continuity, microamps and LRA Inrush. The DL489 is the complete meter your job requires.
-
product
Programmable Linear DC Power Supply, 2 Output, 0-32V/0-3A
T3PS23203P
Programmable Linear DC Power Supply, 2 Output, 0-32V/0-3A.
-
product
Current Transformer
DCT 57
Shanghai Powoo Industry Develop Group Limited
Accurate DC measurement, comply to IEC 1036 and IEC 62053. Suitable for a wide range of current (from 1.5A to 100A); linear output current, high precision; compact, delicate appearance.
-
product
DC Power Supply
62000P series
Chroma's new 62000P Series of programmable DC power supplies offer many unique advantages for ATE integration and testing. These advantage include a constant power operating envelope, precision readback of output current and voltage, output trigger signals as well as the ability to create complex DC transients waveforms to test device behavior to spikes, drops, and other voltage deviations.Designed for automated testing DC-DC converters and similar products, the 62000P sets a new standard for hi...show more -
product
DC Power Supplies
DCS Series
AMETEK Programmable Power, Inc.
The DCS Series of 1 kW, 1.2 kW and 3 kW programmable power supplies provides a highly reliable power platform. It utilizes unique packaging techniques to achieve continuous full output power (1 kW, 1.2 kW or 3 kW) in any volt/amp combination within the rated output voltage and current limits in a low profile chassis. This DCS power supply family has an easy-to-use front panel with 10-turn potentiometers to adjust voltage and current settings that are displayed simultaneously. LEDs indicate overt...show more
