PCB Inspection
The check and evaulation of Printed Circuit Boards.
See Also: Visual Inspection, Bed of Nails, Flying Probes, AOI, Burn-In, Automated Optical Inspection
-
Product
Post Wire and Die Bond Inspection Machine
IV-E1700
-
IV-E1700 is a post wire and die bond inspection machine that is known for having a proven, effective and patented 2D+3D Inspection system. This product is best used to weed out defects with data collection for process improvement and reports for SPC quality Control.
-
Product
Optical Inspection Machine
3D AOI
-
3D AOI latest optical inspection machine 1. No part dead angle, 4-way projection, complete measurement 2. Part height measurement, accurate measurement of defects 3. Multi-piece inspection without additional program 4. DLP digital projection, program editable height measurement
-
Product
Automated Optical Inspection System
AV880 Series
-
The AV880 Series of AOI solutions from ASC International provides the same high level inspection capabilities as found in our AV862/AV871 Series of AOI systems all wrapped into an inline platform for continuous flow requirements. A price to performance ratio sure to please those looking for a quick ROI.
-
Product
PCB S.I/P.I (Signal Integrity/ Power Integrity)
-
Why need for PCB Simulators?Higher data speed (>GHz) Higher density Larger system size EMI concern Cost cut down Reduce of project term
-
Product
High Force Type Probe For PCB, K100 Series 100mil Pitch, Type D, Ø0.80mm, 230gf
K100-D080230-SKAU
Spring Probe
K100 Series, Pitch 100mil, Tip Style D, Tip Diameter Ø0.80mm, Spring force 230gf, Steel with Gold Plating.
-
Product
Magnetic Particle Inspection
-
Shanghai Xianda Denshijiki Industry Co.,Ltd
Using the "leakage magnetic flux" phenomenon generated from the scratches, the magnetic powder (or fluorescent magnetic powder) of the ferromagnetic material scattered on the surface by magnetizing the specimen is adsorbed to the scratch. Observe this and detect scratches.
-
Product
PCB Data Logger
DL-3
-
The PCB Data logger is a proprietary data logger designed by DLM for use in the offshore industry. Comprising of multiple on-board sensors and with extra capacity for external mV or mA inputs, the DL-3.0 can sample on-board and external sensors at customisable sample rates of up to 800Hz.
-
-
Product
Coax, Module, Receiver, CASS, 64 Position, Discrete Wiring or Side PCB
510113121
Receiver Module
Coax, Module, Receiver, CASS, 64 Position, Discrete Wiring or Side PCB.
-
Product
37-Pin D-Type Male Right Angled PCB HV
40-963-037-RM-HV
-
Accessory allows a user to create their own PCB based termination solution mounted directly on the front of the product or on the end of a cable. Interfacing PCBs should be designed with suitable clearances for the voltage the application requires. 37-Pin Female connectors can be directly mated to a corresponding Pickering Switching Module while Male versions can be used to interface to a Female cable assembly termination.
-
Product
160-Pin DIN41612 Connector, Straight PCB Mount, Female
40-963-160-SF
-
Accessory allows a user to create their own PCB based termination solution. This connector is not suitable for directly mounting onto a Pickering switching or cabling product.
-
Product
Inspection Tools
Multi Disk Test System (4-Port)
-
16 types of inspection modes can be registered and edited. More accurate acceptance inspections can be performed using various types of inspections.High speed data communications using USB interface for communicating with host computer.Acceleration testing for temperature loaded HDD can also be performed. (Optional)Easy attaching and removing HDD using optional plug-in unit.
-
Product
Lab Inspection & Testing Services
-
Our lab services use advanced techniques to thoroughly inspect components for manufacturing flaws before assembly. We work with clients in the aerospace, automotive, oil & gas, manufacturing, wind energy, and various other industries to ensure their materials and components are free from defects that were introduced in forging or manufacturing processes.
-
Product
Semiconductor Package Inspection System
-
NIDEC-READ GATS (Grid Array Testing System) series carry out open/leak circuit tests on semiconductor package (MCM/CSP/BGA).
-
Product
Semiconductor Wafer Microscope Inspection System
MicroINSPECT
-
MicroINSPECT Semiconductor Wafer Defect Microscope Inspection System combines state-of-the-art robotics, intelligent microscopes and SITEview software to provide a flexible, easy-to-operate defect inspection platform for either micro or macro defect wafer inspection.
-
Product
Electronic Inspection Systems
-
Intego's knowhow even makes it possible to identify challenging defects that may be located under the surface. One system is the inspection of chips by means of lock-in thermography, which visually represents the IR radiation intensity signal of electronics. Special lasers and flash lamps generate a very short heat impulse (10 ms) on the chip, which generates a measurable heat flow. In most cases, a resolution of < 1 μm can be achieved.
-
Product
High Force Type Probe For PCB, K100 Series 100mil Pitch, Type L, Ø1.50mm, 305gf
K100-L150305-SKAU
Spring Probe
K100 Series, Pitch 100mil, Tip Style L, Tip Diameter Ø1.50mm, Spring force 305gf, Steel with Gold Plating.
-
Product
Edge Card Adapter, Universal, for .062 PCB
111107138
Edge Card Adapter
VPC provides two types of Edge Card Adapter Kits for 10, 25 and 50 Module ITA Enclosures. Both kits are designed for various sized cards.The Universal Edge Card Adapter Kit’s card guides are hinged and can be folded for storage by releasing the holding latches on either side of the card.
-
Product
96-Pin SCSI Micro-D Right-Angle PCB
40-963-096-RM
-
Accessory allows a user to create their own PCB based termination solution mounted directly on the front of the product or on the end of a cable. Interfacing PCBs should be designed with suitable clearances for the voltage the application requires.
-
Product
High Force Type Probe For PCB, K100 Series 100mil Pitch, Type I, Ø1.26mm, 230gf
K100-I126230-SKAU
Spring Probe
K100 Series, Pitch 100mil, Tip Style I, Tip Diameter Ø1.26mm, Spring force 230gf, Steel with Gold Plating.
-
Product
High Force Type Probe For PCB, K100 Series 100mil Pitch, Type I, Ø1.26mm, 305gf
K100-I126305-SKAU
Spring Probe
K100 Series, Pitch 100mil, Tip Style I, Tip Diameter Ø1.26mm, Spring force 305gf, Steel with Gold Plating.
-
Product
Automatic Flight Inspection Systems
AT-940
-
The AT-940 is a mobile and deployable flight inspection system providing high performance in the smallest possible package.
-
Product
160-Pin DIN41612 Connector, Straight PCB Mount, Female
C1604FX-4PS-0A
DIN41612 PCB-Mount Connector
Accessory allows a user to create their own PCB based termination solution. This female connector is modified to enable it to be fitted to Pickering's 40-967-160-F cable assembly
-
Product
Coax, Module, Receiver, CASS, 64 Position, Center PCB Mount
510113122
Receiver Module
Coax, Module, Receiver, CASS, 64 Position, Center PCB Mount.
-
Product
9 Pin D-Type, Male, Straight PCB Mount, HV
40-963-009-SM-HV
D-Sub PCB-Mount Connector
9-Pin Male D-Type Connector, High Voltage - Straight PCB Mount
-
Product
PCB IMIB01, 100 mV/g, IEPE, 15 kHz, 2-Pin, Accelerometer, Industrial Vibration Sensor
784176-01
-
The PCB IMIB01 is an industrial Vibration Sensor designed for permanent installations. This sensor helps you acquire sound and movement data with supported PXI Sound and Vibration Modules, C Series Sound
-
Product
PCB GPTC03, 10 mV/g, IEPE, Accelerometer, General-Purpose Vibration Sensor
780988-01
-
The PCB GPTC03 helps you acquire sound and movement data with supported PXI Sound and Vibration Modules, C Series Sound and Vibration Input Modules, and USB-based Sound and Vibration Devices. This sensor uses the … Integrated Electronics Piezo-Electric (IEPE) current excitation. The PCB GPTC03 features a sensitivity range of 10 mV/g and requires a low-noise coaxial cable.
-
Product
Fiber Optic Inspection & Cleaning
-
One of the most basic and important procedures for the maintenance of fiber optic systems is to clean the fiber optic equipment.
-
Product
High-speed In-Line 3D CT Inspection System
X-eye 6300
-
Automatically inspects the defects of products in customer's line with high-speed 3D CT tomography.Able to inspect every defects of Double-sided PCBA & BGA mounted components precisely by solving overlapped X-ray image issue.Inspection speed of 3 sec/1FOV from loading to automatic Good/NG judgement.
-
Product
Automated Optical Inspection Solutions
-
Adjustable criteria for different process application or modelFlexible algorithms programming editor for mono-crystalline and multi-crystalline silicon solar cellsMultiple interface to communicate with manufacturing equipment or information systemVarious defects inspection capability from multilayer LED lighting designFlexible design that can be easily integrated to your in-line printing system and sorting system
