Current Sources
See Also: Programmable Current Sources, Battery, Voltage Current Sources
-
Product
Current And Voltage Input Sensors
-
Current input sensors monitor current from inverters in solar panel and wind turbine applications and turn the current into voltage which can be measured with an analog input type data acquisition module for analysis. Voltage Input Attenuators can be used to measure high voltages. Voltage Attenuators are designed for used in high-voltage applications. The current can be converted into +/-10 Vpp attenuated signal, so that a general electronic measuring device is able to read the signals.
-
Product
Current Amplifiers
-
In order to achieve an extremely low noise performance very high gains were chosen, while nevertheless minimizing the associated bandwidth reduction.Thus, as a result of our sophisticated development efforts we can offer a professional "High-End" Current Amplifier line. The noise performance of our products surpasses by far that of conventionally designed OpAmp current-to-voltage converters at the corresponding bandwidth.
-
Product
Laser Source
TW3111
-
Techwin(China) Industry Co., Ltd
Laser Source TW3111 is a handheld optical light source, newly released in 2007. It can provide 1 to 6 wavelengths output to satisfy specific requirements including the 650nm visible light source and the 1310/1550nm wavelengths for single mode fiber or the 850/1300nm wavelengths for multimode fiber, as well as other wavelengths according to customer's needs. Together with the TW3211 optical power meter, it is a perfect solution for fiber optic network applications.
-
Product
Light Source Colorimeter
CX-HP2
-
Shenzhen Chuangxin Instruments Co., Ltd.
Light source colorimeter is a newly developed pocket colorimeter, adopting advanced spectrometer and microprocessor technology. It makes traditional laboratory instrument available for the production on-line quality acceptance, thus greatly improve the efficiency of fluorescent lamp, CFL, LED manufacturing.
-
Product
Current Shunt Module
CURS100
-
The CURS100 converts a current signal output by a sensor or output device (e.g., 4 to 20 mA) to a voltage that can be measured by a datalogger. The 100 ohm resistor used for the current shunt allows currents up to 25 mA to be read on a 2500 mV range (CR10, CR10X, CR510, CR500) and currents up to 50 mA to be read on a 5000 mV range (CR23X, 21X, CR7, CR5000, CR9000, CR9000X).
-
Product
Capacitors - Power - Heavy Current (ESTA)
-
Vishay ESTA is one of the few manufacturers to offer a complete range of power capacitors. These cost-effective devices for harmonic control, energy savings, and voltage stabilization are highly reliable and environmentally safe, and can be used under the most rugged conditions. Vishay ESTA power capacitors address a wide range of energy-generation applications. Their “green” applications include energy generation in on- and off-shore wind turbines and solar power plants.
-
Product
Ionization Sources
-
BaySpec offers many types of ionization sources to use with our Portability™ and Continuity™ portable mass spectrometers. Delivering ultimate mobility and ease of use, BaySpec’s Portability™ and Continuity™ are compatible with ambient ionization techniques, which do not require any gases or tanks to run measurements. Making it ideal for field analysis, ambient ionization does not require sample preparation; sample introduction quick, direct, and easy to perform by anyone in any location. Providing flexibility to perform applications using various ionization techniques, the external ionization sources can also easily be swapped in less than a minute.
-
Product
Light Source
UVM-SP-JW
-
Readouts of UV intensity and cumulative luminescence count are prompted either on the front panel or via the externally connected remote signal control. The UV intensity detection segment is intended to measure a specific intensity of light signals, while the cumulative luminescence count is designed to tally a cumulative count on all UV intensities measured, in conjunction with real-time calibration.
-
Product
AC to AC Programmable Power Sources
AFV-P Series
-
Rating:600 VA to 5 KVASingle Phase OutputOutput frequency: 45 Hz to 500 Hz (Optional for 15 Hz to 1000 Hz)
-
Product
GLORIA-X150A/ Xenon Light Source
-
Xe arc lamp light sources are the preferred artificial sources to simulate sunlight. The high color temperature (6000K) of the Xenon lamps is a close match to the solar temperature. This results in very similar solar spectra in the UV and VIS although the source has some Xe emissions lines in the near IR. Application for fluorescence, luminescence and phosphorescence, absorbance and reflectance, photochemistry, photolithography, solar simulation and so on.ct description goes here.
-
Product
Basic Current Clamps
-
PeakTech Prüf- und Messtechnik GmbH
Are ideal for current measurement in electrical systems and control cabinets, since only single wires are guided through the clamp jaws for contact-free current measurement and no electrical connections have to be disconnected. This method also enables measurements of very high currents, which would overload any standard multimeter if connected directly.
-
Product
Current Loop 20 MA Constant Current SI-module With Optical Isolation
MXTTY
-
Current loop 20 mA constant current (active, passive) SI-module with optical isolation.
-
Product
AC Power Source
SPS-100
-
Kongter Test & Measurement Co., Limited
SPS-100 is designed for various tests of analog and digital AC Voltage meter and Current meter, Single/three phase active and reactive power meter, Phase angle meter, Single/three phase power factor meter, frequency meter, and synchronous-meter, Single/three phase active and reactive power meter; it also outputs 2nd ~63rd harmonics.
-
Product
Dual Source Energy Meter
-
Directly replaces 2 energy meters Sensing dual source through 240V connection Dual row display switches based on the source Displays basic and most of the power parameters Optional digital output separately for EB or DG parameters
-
Product
Current Measurement Probes
-
Comprehensive line of clamp-on current probes covers the entire spectrum of applications, from electrical panels to substations. AEMC Current Probes measure current without interrupting the circuit under test and extend the measuring capabilities of DMMs, recorders, power meters, and loggers. The numerous jaw sizes are designed to accommodate a wide variety of conductor diameters and ranges. Available for AC or DC measurements.
-
Product
AC Leakage Current Tester
229-2
-
Testing for dangerous small leakage currents is easy with the Simpson Model 229-2 Leakage Current Tester. For use in appliance field service, in the lab, or in production, the 229-2 approximates the human threshold of perception in detecting hazardous AC leakage current. The 229-2 comes with test leads with alligator clips, manual and batteries.
-
Product
High Current Probes P19711B130G130TL106STS2
1042316
-
The High Current Probes P19711B130G130TL106STS2, designed under the family P-T / P197T-L106, is a remarkable solution for high precision connectivity in various demanding environments. With a temperature tolerance ranging from -45°C to +200°C, these probes are engineered to deliver under severe conditions while maintaining optimal performance. The continuous current capacity of 9.00 A ensures reliable operation, making this probe ideal for critical applications in electronic testing and measurement.
-
Product
Split type AC Current Transformer
CTS-200
-
MULTI MEASURING INSTRUMENTS Co., Ltd.
*1A output for metering application.*Short circuit switch for secondary output is provided for safe operation.*High accurate transformer for the application of first class meter.*Easy installation by metal fitting.
-
Product
Clamp type AC Current Sensor／for Leakage Current Measurements(ZCT Series)
ZCT-150T
-
MULTI MEASURING INSTRUMENTS Co., Ltd.
*Easy installation.*For leakage current measurements of bus bar*Unique split and track type ZCT sensor*High sensitive and least affection from external magnetic field
-
Product
Opto-Isolated Current Loop Signal
4029
-
SPECTEC Innovative Sensor Solutions
SPECTEC's Model 4029 digital opto-isolated current loop signal conditioner prevents ground loops and interrupts any galvanic signals riding on magnetic speed sensor's output signal.. This signal conditioner converts magnetic, variable reluctance and inductive sensors' sinusoidal signals into a 4-20 mA output suitable for interfacing with process control units, dataloggers, flow controllers, and computers.
-
Product
Handheld Optical Light Source
JW3109
-
Shanghai Joinwit Optoelectronic Tech,co.,Ltd
An easy-to-use optical light source which offers high accuracy and is used to test single and multi-mode optical fibers by using 1 to 4 output wavelengths.
-
Product
Laser Source
TW3109
-
Techwin(China) Industry Co., Ltd
can provide 1 to 4 output wavelengths to meet specific requirements, including the 650nm red source and the 1310/1550nm wavelengths for single mode fiber or the 850/1300nm wavelengths for multimode fiber, as well as other wavelengths according to customer needs. Together with the TW3208 optical power meter, it is a perfect solution for the fiber optic network characterization.
-
Product
PXIe-4147, 4-Channel, ±8 V, 3 A Precision PXIe Source Measure Unit
786888-01
Source Measure Unit
PXIe, 4-Channel, ±8 V, 3 A Precision PXI Source Measure Unit - The PXIe-4147 is a 4-channel source measure unit (SMU) ideal for high-pin-count applications. It features 4-quadrant operation, and each channel has integrated remote four-wire sensing for accurate measurements. The sample rate of the PXIe-4147 can reduce measurement times, capture transient device characteristics, and help you perform current-voltage (I-V) characterization of devices-under-test (DUTs). With a high-speed sequencing engine, you can synchronize SMUs with each other or with other instruments such as switches or high-speed digital test modules. Additionally, you can tune the PXIe-4147 response to any load to achieve optimum responses with maximum stability and minimum transients using SourceAdapt technology.
-
Product
Series Precision Multi-Ratio Current Transformers
PMT25090
-
Power Measurement Technologies Inc.
Precision two-stage toroidal current transformers find application as the reference in determining the accuracy of instrumentation current transformers.
-
Product
AC Power Source
SPS-50
-
Kongter Test & Measurement Co., Limited
SPS-50 standard power source is applied for various tests of analog and digital AC voltage meter and current meter, single/three phase active and reactive power meter, phase angle meter, single/three phase power factor meter, frequency meter, and synchronous-meter, single/three phase active and reactive power meter. It also output 2nd ~63rd harmonics.
-
Product
Source Measurement Unit
SMU8
Source Measure Unit
The SMU8 offers high voltage SMU in a compact, 3U PXI / USB form factor. The SMU8 supports 0V to +4V 0.5A or 0V to +12V 25.6mA with FVMI, FVMV, FIMV, FIMI modes. 8 channel can be ganged to support high current driving.
-
Product
AC / DC Current Clamp
HT9025
-
HT9025 has been designed to measure AC/DC current up to 1000A, DC voltage up to 1500V and AC voltage up to 1000V in TRMS reaching CAT IV 600V and CAT III 1000V in compliance with safety standard IEC/ EN61010-1.
-
Product
Precision High Current Resistors/Shunts
-
Measurements International Ltd.
The precision high current shunts are a series of High Current Resistors ranging from 1 A to 3000 A with optional air moving fans and resistance values from ohms to micro-ohm.
-
Product
Current Probes
-
Tektronix current probe solutions offer:*The broadest range of AC/DC and AC-only current probes*Measurement accuracy from uAs to 2000 A*Best-in-class bandwidth up to 120 MHz*Best-in-class current clamp sensitivity down to 1 mA*The only products with 3rd Party Safety Certification (UL, CSA, ETL)*The only products with bare wire voltage ratings*Automatic readout and scaling when used with Tektronix oscilloscopes so you don’t have to convert volts to amps or manually set the scaling
-
Product
Split type AC Current Sensor
CTF-200A
-
MULTI MEASURING INSTRUMENTS Co., Ltd.
* Suitable for current measurements of feeder. * Wire stopper is equipped for the slipping protection. * The special connector is not necessary as the output terminals are provided. * Open circuit protection and nonflammable plastic material.
