Amplifiers
increase the amplitude of a signal.
See Also: Amp, RF Amplifiers, Preamplifiers, Current Amplifiers, Audio Amplifiers, Voltage Amplifiers, Transconductance Amplifiers, Op Amps, Klystron, Instrumentation Amplifiers, Distribution Amplifiers
-
product
2-Ch 500 MHz A/D w/ DDC & 2-Ch 800 MHz D/A w/ DUC, Virtex-6 FPGA - 3U VPX
Model 52651
- Complete radar and software radio interface solution- Supports Xilinx Virtex-6 LXT and SXT FPGAs- Two 500 MHz 12-bit A/Ds- Two multiband DDCs (digital downconverters)- Two 800 MHz 16-bit D/As- One DUC (digital upconverter)- Multiboard programmable beamformer- Up to 2 GB of DDR3 SDRAM or 16 MB of QDRII+ SRAM- Sample clock synchronization to an external system reference- LVPECL clock/sync bus for multimodule synchronization- Optional LVDS connections to the Virtex-6 FPGA for custom I/O- 3U VPX form factor provides a compact, rugged platform- Compatible with several VITA standards including: VITA-46, VITA-48 and VITA-65 (OpenVPX™ System Specification)- Ruggedized and conduction-cooled versions available- Synchronize up to eight modules with Model 7893 System Synchronization and Distribution Amplifier - PCIe
-
product
1-Channel 3.6 GHz or 2-Channel 1.8 GHz 12-bit A/D with DDC - 3U VPX
Model 52741
- Ideal radar and software radio interface solution- Supports Xilinx Virtex-7 VXT FPGAs- GateXpress supports dynamic FPGA reconfiguration across PCIe- One-channel mode with 3.6 GHz, 12-bit A/D- Two-channel mode with 1.8 GHz, 12-bit A/D- Programmable one- or two-channel DDC (Digital Downconverter)- 4 GB of DDR3 SDRAM- µSync clock/sync for multiboard synchronization- PCI Express (Gen. 1, 2 & 3) interface up to x4- Optional user-configurable gigabit serial interface- Optional LVDS connections to the Virtex-7 FPGA for custom I/O- Compatible with several VITA standards including: VITA-46, VITA-48 and VITA-65 (OpenVPX™ System Specification)- Ruggedized and conduction-cooled versions available- Supports GateXpress® FPGA-PCIe Configuration ManagerSynchronize up to twelve modules with Model 9192 System Synchronization and Distribution Amplifier- 1U Rack-mount
-
product
Amplifier-in-Cable Small Proximity Sensor
EM Series
Amplifier-in-Cable Small Proximity Sensor. Ultra-small sensor head. Amplifier and operation indicator built into cable. Strong, flexible cable IP-67 waterproof housing
-
product
Four Quadrant Power Amplifier For Simulation Applicaton
PAV30000
PAV Series Four-quadrant Simulation Power Amplifier based on linear power amplifier technology and integrated advanced technical performance and rich functions.
-
product
RF Amplifier
MLE-02-1G
Hangzhou Softel Optic Co., Ltd.
MLE-02 is kind of bidirectional amplifier with one input port and one output port, which forward gain range from 28dB to 41dB and the max gain of reversed path can reach 23dB. It can be used as a trunk amplifier in the traditional coaxial network, also it can be used as an line extender amplifier in the HFC network. Its tank-type construction is convenient for maintenance.
-
product
1.5µm PM Ev-Yb Fiber Amplifier ( PM EYDFA )
HAPM5000
Hangzhou Huatai Optic Tech. Co., Ltd.
Huatai HAPM5000 is a C-Band Polarization Maintaining Optical Amplifier which worked in 1540~1570nm operating wavelength. Adopt Polarization Maintaining (PM) Multiclad Ev-Yb fiber, output optical power range 27~37dBm(0.5W~5W) ， extinction ratio >20dB.
-
product
Photo Detector with Integrated Transimpedance Amplifiers
ADN3010-11
Analog Devices optoelectronic amplifiers include a range of germanium photodiodes that, through a proprietary process, have been monolithically integrated with silicon transimpedance amplifiers and limiting amplifiers. This process eliminates the need for bond wires connecting the photodiode to the transimpedance amplifier, which leads to improved performance and greater manufacturing reliability. Our portfolio of products also supports the growing need for optical and electrical interface miniaturization.
-
product
LINEAR AMPLIFIERS
These amplifiers are designed to extend the output range of low voltage signal sources. They are general purpose devices with a very low output impedance and fast response. The output is linear from DC up to megahertz range.
-
product
Monolithic Balanced Mixers With Intermediate Frequency Amplifier
Insight Product Company offers Monolithic Balanced Mixers with and Intermediate Frequency Amplifier in frequency range of 26 to 178 GHz.
-
product
Bi-Directional Amplifiers
Fairview’s bi-directional amplifier models are designed for use in both commercial and military applications and will support any signal type and modulation format such as 3G and 4G telecom, WLAN, OFDM, DVB and CW/AM/FM. Fairview’s bi-directional amplifiers offer high power density, efficiency and linearity in small lightweight environmentally sealed packages with SMA connectors. These units also feature a quick-connect circular locking connector for DC and control functions and each design uses a single voltage supply with voltage regulation.
-
product
8 Channel A/D & D/A Zynq UltraScale+ RFSoC Processor - SOSA Aligned 3U VPX
Model 5550
- Now available in RFSoC Gen 3 with the Model 5553- Supports Xilinx® Zynq® UltraScale+™ RFSoC FPGAs- 16 GB of DDR4 SDRAM- On-board GPS receiver- 10 GigE Interface- 40 GigE Interface- Optional VITA 67.3C optical interface for backplane gigabit serial communication- Dual 100 GigE UDP interface- Compatible with several VITA standards including: VITA 49, VITA 46, VITA 48, VITA 67.3C and VITA 65 (OpenVPX™ System Specification)- Ruggedized and conduction-cooled versions available- Model 8256 3U VPX SOSA Aligned Development Chassis- Model 6001 unique QuartzXM eXpress module enables migration to other form factors- Video: Model 8256 3U VPX SOSA Aligned Development ChassisPentek's Quartz Family of Xilinx Zynq UltraScale+ RFSoC FPGA Products Video- Live Signal Acquisition Video: Quartz Model 5950 and Model 6001 RFSoC boards- Pipeline Newsletter: Strategies for Deploying Xilinx's Zync UltraScale+ RFSoC- Synchronize up to eight modules with Model 5903 High-Speed System Synchronization and Distribution Amplifier - 3U VPX- Please refer to the product datasheet for Installed FPGA IP Module details
-
product
Charge Amplifier for Outputs from Piezoelectric- or mV-type Accelerometers, Force Gauges, Microphones & Pressure Pickups
Trig-Tek™ 201AP
Amplify the outputs from piezoelectric- or mV-type accelerometers, force gauges, microphones, and pressure pickups
-
product
Cable Tracing
Tone and Probe
The Amplifier Probe is designed to identify and trace wires or cables within a group without damaging the insulation. It allows for pin point identification even in the most congested cable bundles. Our unit can be used with any tone generator.
-
product
MOSFETs For High Frequency Amplifier
The MOSFETs shown below are best suited for amplification of high-frequency signals.
-
product
Power Amplifiers
Analog Devices MMIC-based GaN and GaAs power amplifiers cover the low hundred MHz frequency range up through and including components in the W band (75 GHz to 110 GHz). In addition to components, our portfolio also includes GaN-based power amplifier modules with output power exceeding 8 kW. Designed for excellent linearity at high output power, our power amplifiers maintain good heat dissipation and high reliability at elevated temperatures for the wide variety of wired and wireless applications that they are used in.
-
product
Pre-Amplifiers
MPR, MDA series
MPR, MDR series provides low noise, high gain and wideband to improve dynamic range for emission testing. We also offer customized model for variable requirments.. Example 30M-1000MHz with band-pass filter Amprifier unit for connecting antenna directly
-
product
Basic Quad K-Type Analog Thermocouple Amplifier
SEN-30103-K0
Analog thermocouple amplifier board based on the AD849x from Analog Devices (successor of the AD597). This quad-channel thermocouple board converts the very low voltage signal from a thermocouple to a highly-linear, 0.005V/C output with either 0V or 1.245V offset (both configurations stocked) while removing unwanted noise from the signal. Many supply and output configurations are available with this board, though the PCB was designed with Arduino in mind. Specifically, the output header will plug directly into a standard Arduino Uno or Mega, with a pin-for-pin match for power supply, ground and analog outputs. With a 5V Arduino, temperatures from 0C to 1,000C are possible with the 0V offset board and -249C to 750C with the 1.245V offset board. If using a 3.3V microcontroller (Due, etc), the board must be supplied with no more than 3.3V to avoid damaging the microcontroller. Temperature measurement range is dependent on the supply voltage. It is possible to supply the board with higher voltages to allow temperature measurement over the entire operating range of the K-Type and J-Type thermocouples, allowing use with more capable data acquisition equipment.
-
product
Amplifier
C-Band
Amonics offers polarization maintaining EDFAs for various applications. Including free space communications, coherent beam combining, and detection system. The output light is linearly polarized with high polarization extinction ratio. The compact turnkey benchtop or 19" rackmount instrument incorporates a user-friendly front panel housing with a LCD monitor display, key switch, power adjust control knob and optical connectors. A RS232 or Ethernet computer interface is also equipped.
-
product
3-Ch 200 MHz A/D with DDC & 2-Ch 800 MHz D/A with DUC, Kintex UltraScale - 6UVPX
Model 57821
- Jade Xilinx Kintex UltraScale FPGA Products and Navigator Design Suite Software Video- Jade Xilinx Kintex UltraScale FPGA Family Brochure- Complete radar and software radio interface solution- Supports Xilinx Kintex UltraScale FPGAs- Three 200 MHz 16-bit A/Ds- Three multiband DDCs (digital downconverters)- One DUC (digital upconverter)- Two 800 MHz 16-bit D/As- 5 GB of DDR4 SDRAM- Sample clock synchronization to an external system reference- LVPECL clock/sync bus for multimodule synchronization- PCI Express (Gen. 1, 2 & 3) interface up to x8- Optional LVDS and gigabit serial connections to the FPGA for custom I/O- Compatible with several VITA standards including: VITA-46, VITA-48 and VITA-65 (OpenVPX™ System Specification)- Ruggedized and conduction-cooled versions available- Synchronize up to eight modules with Model 7893 System Synchronization and Distribution Amplifier - PCIe
-
product
Amplifiers
Amplifiers from Analog Devices deliver both high performance and high value. These amplifier ICs combine circuit design, manufacturing process innovation, and applications expertise to create products that simplify signal conditioning design.
-
product
Single and Multi-Function High Power Amplifiers
This lab unit is capable of a power output of 30 Watts and operates at a frequency range from 1200 MHz to 1400 MHz. The compact and rugged design of this system is ideal for bench-top testing and many other applications where both simplicity and portability are required.
-
product
Broadband Amplifier
BBA300
The R&S®BBA300 broadband amplifiers are a new generation of highly compact solid-state broadband amplifiers designed for high availability. They feature extremely wide, continuous frequency bands extending up into the high microwave range, along with high linearity, outstanding noise power density and excellent harmonic characteristics. They also boast high system configuration and operational settings flexibility.
-
product
Galvanic Isolation Amplifier
X005 Series
The X005 Galvanic Isolation Amplifier provides a regulated and resistively limited +5V dc power supply required by the sensors, it can be connected in three or five wire modes. Used in five wire mode positive and negative sense inputs enable the X005 to dynamically adjust the sensor supply thus ensuring the correct voltage across the sensor. Connected in this way the X005 can compensate for 15 conductor resistance. The sense terminals are linked internally so the end user can use the X005 in three wire or five wire mode without the need to fit or remove external links.
-
product
Current Feedback Op Amplifiers
Analog Devices high speed (> 50 MHz) current feedback op amps enable you to operate at higher speeds. Current feedback op amps traditionally have wider bandwidths and higher slew rates than voltage feedback amplifiers and do not feature a gain bandwidth restriction associated with voltage feedback op amps.
-
product
RF Amplifier
SA822
Hangzhou Softel Optic Co., Ltd.
SA822 860 MHz outdoor distribution amplifiers are mainly used for bidirectional trunk transmission of CATV television image signal, digital TV signal, telephone voice signals and data (or compressed data) signal.
-
product
Single Channel High Voltage Linear Amplifier
A600
The A600 is a general purpose broadband linear amplifier having a fixed amplification of 100 times and capable of bipolar high voltage output of 300V. Any functiongenerator or arbitrary waveform generatoror any othe signal source with amplitude up to 3 V can be used as an input device. The amplifier's output is linear from DC up to megahertz range. It can be used in a wide range of applications, for example to drive piezo actuators, MEMS, OLEDs, liquid crystals, etc.
-
product
Linearizers
Gain Shape Linearizer Amplifiers are used in a number of applications where it's necessary to flatten the gain characteristic of the preceding or following component. This would include flattening the attenuation of a long cable run, or perhaps changing the input gain response to a MPM (Microwave Power Module) or TWT (Traveling Wave Tube) to compensate for the gain variation within the tube.
-
product
System Amplifier
SAM100
The R&S®SAM100 system amplifier is an ultra-broadband solid state microwave amplifier with a frequency range from 2 GHz to 20 GHz. With a power of up to 20 W, outstanding linearity and very good noise characteristics, the R&S®SAM100 amplifier is ideal as a compact system amplifier in various measurement setups e.g. design (DVT) and product validation test (PVT) or EMC. In measurement environments with R&S generators, frequency analyzers or network analyzers, they can act as drivers or boosters and amplify the measurement signals
-
product
3-5 Watt Power Amplifiers
CCM1095 and CCM2096
The CCM1095 and CCM2096 are power amplifiers that use current efficient Silicon Carbide output semi-conductors to achieve +35 to +38 dBm output power. An internal sequencing circuit is included to provide for safe operation of the output power device.
-
product
Test & Measurement Instrument Amplifiers
MPA-series
The MPA-series Test & Measurement Instrument Amplifiers are based on state-of-the-art GaN PA modules and operate from 0.7 to 26.5 GHz (multiple frequency options are available). They provide High continuous power across the band, high linearity for wideband communications testing, have variable gain adjustment and a high-resolution display shows amplifier status. Amplifiers offer a wide range of application-specific requirements including simultaneous high-power, wide bandwidth, low harmonic power and high linearity.
