Hydrogen Detectors
sense the presence of Hydrogen gas.
-
Product
UV/IR Flame Detector
FL500
-
The FL500 UV/IR Flame Detector monitors for radiation emitted by a flame in both the ultraviolet (UV) and infrared (IR) spectral ranges. This UV/IR combination provides a fast response time and increased false alarm immunity against sources of radiation for reliable protection.
-
Product
Metal Detector
Profile Advantage
-
Maximum Sensitivity and Performance; Multi-Simultaneous Frequency & Product Signal Suppression technology deliver the ultimate detection sensitivity with zero false triggering. Simple to Use and Robust Detector Design. Superior performance on wet and conductive products. Product signal suppression overcomes product effect to detect more metal contamination in challenging applications irrespective of packaging type.
-
Product
Long Neck Combustible Gas Leak Detector
CD100A
-
UEi Test & Measurement Instruments
The CD100A is the service persons tool designed to detect combustible gas leaks in residential and small commercial applications. Semiconductor sensor responds instantaneously to all combustible gases. The easily adjusted, steady tic rate provides a precise indication of the leak source. The CD100A can be used in tight quarters where others might not fit.
-
Product
Clamp-On Open-Loop DC MicroAmmeter & Insulation Fault Detector
-
The Clamp-On Open-Loop DC MicroAmmeter & Insulation Fault Detector is a precision tool designed for detecting leakage currents in insulation systems. Featuring high sensitivity, this advanced microammeter measures direct currents as low as 1 microampere (uA) and operates within a measurement range of 10 milliampere (mA) to 10 amperes (A). Utilizing a clamp-on method with a toroidal ferro-magnetic core featuring an air gap, the device integrates AMR sensors from a differential Hall magnetometer for accurate readings. Its design is particularly suitable for large hydro generator stator windings but is also effective in various electrical applications.The device's functionality is significantly enhanced by its use of two micro-ammeters equipped with advanced signal conditioning units and a demagnetization circuit, ensuring precise data acquisition. The accompanying LabVIEW software facilitates real-time monitoring and visualization of data, allowing operators to effectively track leakage currents and identify faults within insulation systems. The dual clamp-on setup enables simultaneous measurements, providing immediate insight into potential defects without the need for cutting conductors or removing insulation, thus ensuring operator safety and system integrity.
-
Product
Chromatography Detectors
-
Brookhaven Instruments Corporation
Detailed size or molar mass distribution information is useful in many areas such as investigating protein aggregation and understanding (or predicting) polymer properties. Since chromatography fractionates a sample before analysis, it is an ideal tool for characterizing these distributions.
-
Product
Integrated Multi-Gas Detector for Unmanned Aerial System
MUVE C360
-
The FLIR MUVE™C360 is a multi-gas detector completely integrated with an unmanned aerial system (UAS) to provide real-time continuous monitoring of chemical hazards while on the move. The sensor block boasts 8-channels, which includes a photoionization detector (PID), Lower Explosive Limit (LEL) detector, and six other sensors. The integrated snorkel is designed to negate the effects of rotor wash, extending past the propellers to sample the unperturbed air. The MUVE C360 sensor block quickly latches to a proprietary integration dock mounted to the UAS. The FLIR calibration station features the same dock, so the operator can easily connect for routine sensor verification. Sensor readouts are prioritized based on alarm conditions and are displayed real-time on the pilot’s interface in the FLIR VueLink™ app. The MUVE C360 is a time-saving, game-changer for emergency responders, industrial safety officers, and environmental monitoring experts.
-
Product
Stealth Laboratory/QA Metal Detector
-
Stealth Laboratory metal detectors are manufactured to suit any application. Designed to be used in offline product examination to assist in determining contaminant source. Stealth detectors use digital signal processing technology and have high sensitivity levels to ensure the detection of the smallest ferrous, non-ferrous and stainless steel contaminants. The built-in data collection software with USB data transfer establishes the Stealth as an effective critical control point complying with stringent HACCP regulations.
-
Product
Toxic Gas Detector
SMC 5100-XX-IT
-
The SMC 5100-XX-IT gas detector monitors toxic gases such as Hydrogen Sulfide, Carbon Monoxide, Nitrogen Dioxide, Ammonia, Oxygen Deficiency, and others. The detector requires calibration only every six months, cutting operating costs and time.
-
Product
Handheld Metal Detector
Xtreme M-7
-
The M-7 handheld metal detector is a perfect partner for use with the XT-8000 portable walk through system or as a stand alone personal search and detection device. Xtreme Research Corporation offers the following product for school security, airport security, etc. Only $239.95 each The M-7 is simple to operate and is essential for searching backpacks, handbags, luggage and lockers. No specialized training or experience is required to operate the M-7 detector.The M-7 is a compact wand type metal detector that can be worn on the belt and weighs just 12 ounces. An optional ballistic nylon belt holster is available along with an earplug which allows silent operation of the M-7.
-
Product
Voltage Detectors
-
Available with a digital readout or a simplified LED display Seaward's specialist range of voltage detectors have the versatility and durability to cope with all types of user demands.
-
Product
Pulse Holiday Detector
NOVOTEST SPARK-1
-
Pulse Holiday Detector NOVOTEST SPARK-1 designed to detect pits, flaws, and holes in different non-metallic insulation coatings (such as polymers, epoxy, bitumen, etc.) and is mostly used for oil and gas metal pipelines and other objects. The device can be used while the pipeline construction, operation or service. Tested coating thickness is up to 12 mm. Such tests are needed to evaluate the oil and gas pipelines corrosion protection reliability.
-
Product
SmartWireless Gas Detector
CXT
-
Teledyne Gas & Flame Detection
All component parts are rated for Class 1; Division 1, Group C, D hazardous areas. These advanced field devices consist of a CXT low power gas detection sensor and wireless transceiver packaged in a single enclosure. Power is provided by a disposable “C” cell battery pack capable of continuous operation for greater than 60 days. Additional power options include a Smart Rechargeble battery with a run time of 5-6 months, a disposable “D” cell battery pack with a run time of 9 months and solar panel providing continuous operation.
-
Product
Solid State Gas Detectors
SMC 20X/200X
-
The SMC 20X/200X are single-gas detectors used to monitor combustible gas, hydrogen sulfide (H2S) or carbon monoxide (CO). The detectors are based on solid-state technology, a simple and robust method of detection capable of detecting low parts-per-million (ppm) levels of gas.
-
Product
Solar Radiation Detector PCE-SPM 1
-
PCE-SPM 1 is a photovoltaic (PV) light meter used to measure solar radiation, solar energy or solar power. The meter's easy-to-read 4-digit LCD screen clearly displays Ptot in W/m² or BTU/(ft² x h), while the device's auto data memory stores up to 43,000 data sets.
-
Product
Flame Ionization Detector
-
A flame ionization detector converts a hydrocarbon gas concentration into an electrical signal. The flame is hydrogen fueled and burns in hydrocarbon free combustion air. Either side of the flame are two electrodes between which an electric field is generated by means of a polarization voltage. The sample is pre-mixed with the fuel gas and heated in the flame to a temperature at which the hydrocarbon molecules ‘crack’ and CH fragments appear. These CH fragments are oxidated by the oxygen in the combustion air resulting in the formation of CHO+ ions. The ion current then passes to the electrodes and the resulting current measured is proportional to the quantity of C atoms derived from organic compounds.The Thermo-FID features two separate microprocessor controlled pressure compensations to avoid any influence from environmental or sample conditions. In addition, the complete Thermo-FID range of analyzers are equipped with a flame trap that is used as a heated sample inlet filter. The measurement chamber and all material in contact with the sample gas are heated between 120°C and 200°C to avoid condensation.
-
Product
Flange-Type High Stiffness Torque Detector
TQ-3507
-
The improvement of energy efficiency has been required in future generation vehicles. The TQ-3507 Torque Detector developed for the measurement of torque capacity 5 kNm accurately captures minute torque fluctuations. It helps to grasp the energy loss precisely and improve energy efficiency of your system.
-
Product
Industrial Gas Detectors
-
Seitron designs and manufactures detectors for methane, LPG, gasoline vapours and carbon monoxide (CO) for commercial and process industry use. Our detectors provide three communication protocols 4..20mA, Modbus and S-Bus (a proprietary protocol derived from Modbus). You can also choose between two types of housings: polycarbonate for industrial use or ATEX-certified for the installation of detectors in ATEX-classified areas.
-
Product
UVC Light Meters & Detectors
-
International Light Technologies
If you are using a UVC light-based disinfection system you are probably scrambling to deploy tools to combat the COVID-19 outbreak. Increasingly facilities are looking to disinfect everything including air, surfaces, instruments, and personal protective equipment (PPE) using UV-C light. Verifying the intensity of the light, or dose, reaching the target is a critical step in validating that the correct UV dose is being applied to ensure proper decontamination.
-
Product
Schottky Mixer and Detector Diodes
-
Macom Technology Solutions Holdings Inc.
Schottky diodes are majority carrier diodes formed by plating a layer of metal on a layer of doped semiconductor, which forms a rectifying junction. The type of metal and the type of dopant in the semiconductor determines the diode’s barrier height, which is a measure of the amount of energy required to force the diode into forward conduction. MACOM produces Si Schottky diodes as well as GaAs Schottky diodes for use as signal detectors or in frequency mixers.
-
Product
Planar-Doped Barrier Diode Detector, 10 MHz to 12 GHz
8471E
Diode Detector
The Keysight 8471E is a low-cost, planar-doped barrier detector offering excellent performance from 10 MHz to 12 GHz. It has an SMA male input connector and an SMC male output connector.
-
Product
Slipping Torque Detector
DI-12 series (SL4/SL02/SL15)
-
Torque measurement of tightened screws. Measure how much force the tightened screw is tightened. By capturing the occurrence of slippage with high accuracy and measuring the torque, it is now possible to measure the torque value of a tightened screw. For sampling inspection of products and setting and management of output torque of power drivers.
-
Product
Ultrasonic Corona & Arcing Detector
ULD-40™
-
The ULD-40™ is an ultrasonic detector designed for corona effect and arcing detection for predictive maintenance in electric utilities. Available with a variety of accessories, this instrument is a cost-effective must for any prevention plan.
-
Product
CO Detector Testing
-
Many multi-sensor fire detectors detect carbon monoxide (CO) as well as smoke and / or heat. Under international codes and standards the CO cell needs to be functionally tested with a CO stimulus from the protected area through the detector vents to the sensor.
-
Product
Explosion Proof Area Hydrogen Monitor
HY-ALERTA™ 2620
-
H2scan’s 2620 Explosion Proof Area Hydrogen Monitor provides hydrogen-specific leak detection and measurement for hydrogen concentrations as low as 4000 ppm and can be scaled to any concentration up to 5% hydrogen by volume, a range representing 10% to 125% of hydrogen’s low flammability limit. The monitor is designed for either ceiling or wall mount. H2scan’s hydrogen-specific sensor technology has no cross sensitivity to other combustible gases, thus eliminating false positive alarms and ensuring safety system reliability.
-
Product
Package Leak Detectors
MFY-02
-
MFY-02 leak tester is suitable for sealing test of products. It can effectively compare and evaluate the sealing process and sealing performance of the soft package through the test. It is an ideal testing instrument for food, plastic soft package, wet towel, pharmaceutical, daily chemical and other industries.
-
Product
Acoustic Fault Detector
AFL212-AMD
-
K&S Engineering and Scientific Ltd
This compact acoustic headset, designed and manufactured by K&S Engineering and Scientific Ltd has been developed with state-of-the-art components to not only to achieve superior performance but also to offer the user an acoustic headset that is smaller than equivalent units currently available on the market. Housed in an IP67 enclosure, the unit, which is used in conjunction with a high voltage surge generator, can easily contend with wet conditions.
-
Product
Temperature Measurement IR Sensors & Detectors
M34
-
A thin-film thermopile in a TO-5 package with an active area of 3.16mm x 0.4mm that offers low noise output.
-
Product
Single Photon Detector System For Near-Infrared (1.6-2.3 Um Wavelength) Waves With Liquid Helium (LHe) Cryostat
-
Insight Product Company is proud to offer Single Photon Detector System for Near-Infrared (1.6-2.3 um wavelength) with Liquid Helium (LHe) Cryostat. Insight Product Co. offers superconducting single photon detectors and ultra-low noise registration systems for the near infrared range. All systems operate in continuous mode, no gating required.
-
Product
Temperature Measurement IR Sensors & Detectors
ST60 TO-5
-
A single-channel silicon-based thermopile provides lowest cost solutions in a small active area of 0.61mm x 0.61mm in a TO-5 package. Time constant of 18ms with Nitrogen encapsulation gas. Delivers a very low Temperature Coefficient of Responsivity of -0.04%/C. This detector has a very short thermal shock response to ambient temperature change.
-
Product
UV/IR Wet Bench Flame Detectors
SMC 3200/3300
-
The SMC 3200/3300 Series Flame Detectors utilize proven, stable UV/IR technology to continuously monitor for flames in wet bench and commercial applications. Due to its compact size, it is also used for installation in certain production equipment.
