Showing results: 511 - 525 of 635 items found.
-
KLA-Tencor Corp
KLA’s metrology systems address a range of chip and substrate manufacturing applications, including verification of design manufacturability, new process characterization and high volume manufacturing process monitoring. By providing precise measurement of pattern dimensions, film thicknesses, layer-to-layer alignment, pattern placement, surface topography and electro-optical properties, our comprehensive set of metrology systems allows chip manufacturers to maintain tight control of their processes for improved device performance and yield.
-
ET Power Systems Ltd.
Electronic test engineers use a variety of precision instruments for R&D, vendor verification, and production testing. ETPS can supply a number of general test instruments that can be used in stand alone mode or automated for high throughput testing. Dedicated battery test systems with automatic charge and discharge modes with data logging are available. The standard 16 and 32 channel systems have range up to 5VDC ensuring their suitability for a wide variety of cells.
-
PGA-VHD -
Hall Research Inc.
he PGA-VHD is a must-have tool for every AV installer and system integrator! This battery operated instrument provides an HDMI input and both VGA and HDMI outputs. The PGA-VHD has a large 4K touch screen for user operation. The display can also act as an HDMI monitor and signal analyzer. Input and outputs support resolutions to 4K UHD @ 60 4:4:4. The PGA-VHD provides a host of tools for verification and troubleshooting of complex AV systems.
-
140BMC/6P -
Aines Manufacturing Corp.
The following tests can be performed using the 140BMC/6P Tone Generator:*1000 Hertz or 500/1000 hertz alternating tone for tracing pairs.*Locates broken pairs/cables in walls. *Tone generator emits R.F. signal detectable by Aines Model 250SSP STATIONMAN Probe or 350 Filter Probe.*Provides talk power on dead pair.*Checks for shorts or opens, using a long-life lite-emitting diode (LED).*Continuity test.*Tip & Ring identifications.*Line condition identification. a. Clear line. b. Busy line. c. Ringing line.*Positive line verification.*Long battery life.*Nylon braided tinsel test lead wire for greater wear and flexibility.*Heavy duty nickel silver Aines 6P type alligator clips with custom designed vinyl boots.*Rubber grommet to prevent chafing on the test leads.
-
National Technical Systems
NTS provides lightning protection engineering, certification plan preparation and verification testing services to airframe and aerospace systems manufacturers around the world. With a lead role in major commercial and military design programs, our engineers take a system-wide approach to assuring that lightning protection is compatible with space and weight limitations, electromagnetic compatibility and electromagnetic pulse. Our experience includes traditional designs, all-composite and fly-by-wire aircraft, as well as avionic upgrades and engine modifications.
-
MB Dynamics Inc.
Experimental modal analysis, or modal testing, is a process for physically obtaining a math model of a structure’s dynamic properties. Modal tests identify a structure’s modal properties: natural frequencies, mode shapes, mass, stiffness and damping. Modal test results help troubleshoot resonant excitation from operating forces, validate and verify finite element models, predict the benefits of structural modifications, support design verification, and understand structural responses due to complex loading conditions.
-
Circuit Check, Inc.
In-circuit testing provides electronic manufacturers a reliable, high fault coverage verification method for the assembly process. Circuit Check ICT fixtures are robust, reliable and designed for easy customization to cover a large range of PCB sizes without impacting turnaround time. We stock a large variety of fixture sizes and actuation methods to meet your test demands. If a stocked sized ICT fixture is not adequate our engineering staff will design a custom solution.
-
Eye-BERT Micro LR -
Spectronix
The Eye-BERT Micro LR is a low cost, easy to use test solution offering BER testing at any rate between 6.312 and 125Mbps on either optical or electrical interfaces. Features include: continuously variable bit rate, user programmable pulse generator, internal CDR with retimer mode, bit rate measurement, and recovered clock output. The Unit is supplied with anti-skid bumpers for bench use, and is small enough to be integrated into larger systems for dedicated link verification.
-
Laser Inspector 1000 -
RJS Technologies, Inc.
The L1000 analyzes the essential traditional verification parameters including average bar deviation, quiet zones, encodation check, mod check and ratio where applicable. It also provides the ISO/ANSI method Decodability calculation and percent of decode information. Designed for maximum ease of use, even traditionally hard to verify bar codes such as high density codes with 5 mil (.13mm) X dimensions and codes on irregular, wet, shiny, laminated or moving surfaces are accurately analyzed.
-
50-262-102 -
Pickering Interfaces Ltd.
This RTD Simulator is a PCI card that supports 6 channels of RTD simulation. The card can provides a setting resolution of <90mΩ (also available in <8mΩ - PT100) and a resistance accuracy of better than 0.1% on all channels. Each simulation channel is able to provide a short or open circuit setting to simulate faulty wiring connections to a sensor. Calibration or verification of each resistor channel can be verified by using the calibration port connected to a high performance DMM and a supplied software package.
-
50-262-101 -
Pickering Interfaces Ltd.
This RTD Simulator is a PCI card that supports 6 channels of RTD simulation. The card provides a setting resolution of <8mΩ (also available in <90mΩ - PT1000version) and a resistance accuracy of better than 0.1% on all channels. Each simulation channel is able to provide a short or open circuit setting to simulate faulty wiring connections to a sensor. Calibration or verification of each resistor channel can be verified by using the calibration port connected to a high performance DMM and a supplied software package.
-
Ranatec Instrument AB
The Ranatec Tunable Notch Filters are critical tools for adaptation to stringent new ETSI/3GPP conformance test specifications for mobile device radio properties, that covers all sub-6 mobile bands and channel bandwidths for 2G/3G/4G/5G. Designed for formal conformance testing performed by accredited test houses, as well internal verification by mobile device vendors. A flexible and easy to use test automation platform to support almost any ambition level, tailored to your demands.
-
FLIR GF346 -
Teledyne FLIR
The FLIR GF346 optical gas imaging camera detects carbon monoxide (CO) and 17 additional gases without the need to interrupt your plant's production process. CO emissions can be a significant threat to primary steel manufacturing operations; even the slightest leak in a vent stack or pipe can have a devastating effect. With the FLIR GF346, inspectors can scan large areas from a safe distance, pinpointing leaks in real-time, reducing repair down-time, and providing repair verification.
-
OBB2 -
Astronics Corporation
The OBB2 is highly configurable and includes built-in standard peripherals (Ethernet, serial, and USB), along with four internal Cores that can be populated with a variety of databus protocols and discrete I/O modules. With the newest advanced set of MIL-STD-1553 and ARINC 429 modules, users can verify wave form compatibilities, test functions of bus shorts and opens, and—when combined with our CoPilot® software—perform lab, production and flight test verification and simulation right out of the box.
-
PFK-105 -
Prostat Corporation
- Ionization Test Kit for Measuring Offset Voltage and Discharge Times- Includes a Field Meter, Charge Plate Monitor, ±1000 Volt Charger and Decay Timer- Balance Ionizers per ANSI/ESD SP3.3 Periodic Verification- Measure Ionizer Decay time as per ANSI/ESD S3.1 and ANSI/ESD SP3.3.- Measure Body Voltage Generation and Decay- Evaluate Ionizers and Packaging Materials- Includes a fixture to hold the PFM-711B, CPM-720B and PDT-740B as one- Molded Carrying Case with Foam Insert Included
