Switch Test
Make, break, or change the connection of a circuit.
-
product
PXI/PXIe Microwave Transfer Switch, Single, 18GHz, 50Ω, SMA
40-782B-521
The 40-782B-521 (PXI) and 42-782B-521 (PXIe) single transfer switches are part of our range of PXI microwave switching modules. They have a characteristic impedance of 50Ω and a maximum operating frequency of 18GHz. Connections are made via front panel mounted high quality SMA coaxial connectors.
-
product
52/20 Channel SPDT Plug-In Switch Card
1260-117/A
The Astronics 1260-117/A is a 52/20-channel, SPDT (Form C) plug-in switch card for the Adapt-a-Switch™ platform.
-
product
Switch Modules - 16 Two Pole Relays Arranged as an 8x2 Matrix
JX16/AB-2
This module has 16 two pole relays arranged as an 8x2 matrix as shown in the figure to the left. The matrix may be operated and wired individually for up to 16 8x2's per chassis, or jumpered to the backplane to form up to a 128x2 two pole matrix. It is available with Type S, M or LT reed relays for high speed, long life application.
-
product
PCIe 2.0 Test Platform
PXP-100B
The Teledyne LeCroy PXP-100B Test Platform provides a convenient means for testing PCIe 2.0 add-in cards with a self-contained portable and powered passive backplane. The PXP-100B provides power required for both cards under test, and an interposer can be used for connection to a protocol analyzer. As an alternative to an interposer, the PXP-100B includes two mid-bus probe footprints to allow connection to an analyzer via a mid-bus probe.
-
product
Noise Figure Analysis Using NI PXI RF Test Instruments
NI-RFmx Noise Figure
Measure noise figure, gain, Y-factor, effective temperatures, hot and cold power, and moreOptimized calibration and measurement routines for multi-DUT test using Y-factor and cold sourceSupports the PXIe-5668R 26.5 GHz VSA, the PXIe-5698 26.5 GHz preamplifier, and VSTsDesigned for use with industry-standard noise sources such as the Noisecom NC346 Series
-
product
PXI Triple SPDT RF Switch MCX 75 Ohm
40-830-103
The 40-830 is a 75 RF Switch available with 3 or 6 separate SPDT relays in a single PXI slot. Both versions have been designed to exhibit low insertion loss and VSWR through the use of modern RF relay technology at an affordable cost. The switch banks have been carefully designed to ensure excellent and repeatable RF characteristics to frequencies of 3GHz with each path having a nominally equal insertion loss. The design of the 40-830 minimizes the injection of noise and unwanted signals into the signal path by careful attention to the mechanical and electrical design.
-
product
Communications Test System for Frontline Diagnostics
CTS-2750
The CTS-2750 is designed using Astronics Test Systems’ proven Synthetic Instrumentation architecture. Featuring 23instruments, and both Automated and Standalone modes to test, record, and diagnose faults, the unit provides complete RF, Analog and Digital capabilities. The field-upgradeable, software-defined architecture features easy-to-use graphical user interfaces and enables testing with minimal operator intervention. Test Program Sets can be created easily using the included TestEZ® software suite.
-
product
CPS-8910 , Switch Device for PCI Express
784307-01
PCI Express, Cabled Switch Device—The CPS‑8910 is designed for large multiple-input, multiple output (MIMO) expansion configurations and system control on the PXI platform or software defined radio devices. The CPS‑8910 provides two PCI Express upstream ports and eight downstream ports for seamless system expansion. You can connect the downstream ports to external devices, such as a Software Defined Radio Reconfigurable Device, to create large multichannel MIMO systems. You also can connect multiple CPS‑8910 switch boxes to a single PXI Express chassis to create massive MIMO systems with a Software Defined Radio Reconfigurable Device. The large data throughput capacity makes the CPS‑8910 an ideal data aggregator for massive MIMO systems. You can use the CPS‑8910 with copper or fiber-optic cables.
-
-
product
ARINC-708/453 2-Channel Test & Simulation Module for the Weather Radar Display Databus
M8K708
The M8K708 module is an ARINC-708 / 453 2-channel test and simulation module for the Weather Radar Display Databus. The M8K708 supports two ARINC-708 / 453 channels, each selectable as transmit or receive. Each channel implements an 64K×16 FIFO and supports polling and/or interrupt driven operation.The M8K708 comes complete with Windows software, a C-driver software library including source code and may be used with Exalt, Excalibur’s Analysis and Laboratory Tools, a Windows monitoring application. In addition, Excalibur produces adapter cables that convert the carrier board I/O Molex™ connector to two twinax CJ70-49 connectors. The cable may be purchased at an additional cost.
-
product
In-Line Test Fixture for 6TL33/6TL36
AB799/AT799
Fixture Kit for Platforms featuring receiver Virginia Panel 9025 and external pusher system. Its heavy duty design supports more than 1.000N.nnThe fixture kit includes the Base fixture (probe plate) as well as the Puhsers plate.
-
product
Mini In-Circuit Test System
U9403A
The Keysight Mini ICT is a true in-circuit test unit in the rack that can be used standalone or integrated. It comes with a full set of Keysight ICT test features, from VTEP vectorless test, Cover-Extend Technology, to digital library tests and boundary scan. The unmuxed per-pin programmable digital engine makes test development really flexible and easy, especially in a situation when device conditioning is needed in functional test.
-
product
2x8 USB Solid State Switch Matrix, 300 KHz To 6.5 GHz
P9165A
P9165A 2x8 USB solid state switch matrix, 300 KHz to 6.5 GHz is a full cross-bar switch matrix that provides a switch based multiport VNA solution in the form of compact USB controlled involving larger scale of multi-DUT or multiport measurements such as 5G massive MIMO antenna measurement and others.
-
product
FPD Tester Model
27014
Chroma 27014 Flat Panel Display Tester is a complete testing solution that meets the Liquid Crystal Module testing requirements of production line. With integrated video generator, multi-channel precision power supply and process control unit, the system allows a complete test of signal, pattern and electrical parameters of LCM through a PC or remote control box.
-
product
PXI Single 2 Channel (M Mode) SC 62.5 Cons
40-855-212-M62.5
Fiber Optic MEMS Switching cards available in many high density formats with a choice of five different connector styles to suit most applications
-
product
High 1.80 (51.00) - 12.60 (357.00) Switch Probe
TSP138-C180-3
Current Rating (Amps): 10Average DC Resistance lower than (mOhm): 20Test Center (mil): 138Test Center (mm): 3.50Full Travel (mil): 197Full Travel (mm): 5.00Recommended Travel (mil): 157Recommended Travel (mm): 4.00Overall Length (mil): 1,760Overall Length (mm): 44.70Switch Point (mil): 67Switch Point (mm): 1.70
-
product
Automotive Ethernet Test Fixture
AE6941A
The AE6941A automotive Ethernet electrical test fixture provides easy access to automotive Ethernet electrical signals so you can perform conformance testing and device characterization quickly and easily.
-
product
PXI Dual 2 x 2 Fibre Optic (M Mode) STM62.5
40-860-522-M62.5
Pickering PXI Fiber Optic MEMS Switching cards are available in many high density formats with a choice of 5 different connector styles to suit most applications: FC/APC (for optimal performance), FC/PC and SC/PC for general applications and LC and MU for high density applications. Fiber optic multiplexers create a signal path by redirecting the optical signal into a selected output fiber. This is achieved using Micro-Mechanical Mirrors driven by a highly precise mechanism and activated via an electrical control signal.
-
product
High Density, 64-Channel Switch Card - 64 Channel, SPDT, High Isolation, Low Crosstalk Switch Module
1260-16A
The Astronics 1260-16A is a 64-channel, SPDT, high isolation; low crosstalk switch module designed for switching and routing sources such as AC and DC power supplies in automated test systems. The 1260-16A switches currents up to 6A, AC or DC, and voltages up to 110VDC or 250VAC.
-
product
Functional Test
xUTS
Extend test to encompass copious test points and DUT varieties along with real-time, hardware-in-the-loop and other state-of-the-art instrumentation. extendedUTS (xUTS) is a custom product for high complexity functional test. Configured for the unique needs of a class of devices under test (DUTs), the xUTS employs our universal test system approach that combines the best open platform instrumentation and software along with mass interconnect technology.
-
product
Universal In-Line Test Platform
UniLine brings 20+ years of test & quality experience to your manufacturing floor and test automation delivers accurate results, without bias. By standardizing test, product quality improves as costs decrease. Equipment becomes understandable and manageable across departments and station support becomes simple.
-
product
PXI Triple SPDT RF Switch 3GHz 50 MCX
40-870-103
The 40-870 is a 50 RF Switch available with 3 or 6 separate SPDT relays in a single PXI slot. Both versions exhibit low insertion loss and VSWR through the use of modern RF relay technology at an affordable cost. The switch banks been carefully designed to ensure excellent and repeatable RF characteristics to frequencies of 3GHz. The injection of noise and unwanted signals into the signal paths of the 40-870 has been minimized by careful attention to the mechanical and electrical design.
-
product
High Density Switching PXI Card
GX6338
The GX6338 is a low cost 6U switching card with 114 individual low level SPST Form A relays capable of switching 0.5 A at 200 VDC. The GX6338 is ideal for applications requiring high density switching.
-
product
Rack based antenna test system
R&S®ATS800R CATR
Very compact far-field over-the-air (OTA) test system based on compact antenna test range (CATR) technologyUnrivaled quiet zone size within 0.8 m2 footprintState-of-the-art reflector ensuring a high quiet zone accuracyUnique rack based CATR system supporting over 50 GHzIndirect far-field method (approved by 3GPP for 5G OTA testing)
-
product
Parametric Test Fixture
U2941A
The Keysight U2941A is a parametric test fixture that is designed to complement the usage of U2722A USB source measure unit in the testing of semiconductor components, including SMT and DIP ICs.
-
product
10 Gigabit Ethernet AdvancedTCA® Fabric Interface Switch Blade
aTCA-3430
The aTCA-3430 is a high performance 10G Fabric switch blade for AdvancedTCAR platforms. This product is ideal for bandwidth intensive telecom applications such as wireless access controllers, DPI/security network, IPTV, IP multimedia subsystems, RNC/BSC, broadband access/bearer networks, data centers, and LTE/4G network applications. The aTCA-3430 provides 10GbE hub-to-node connectivity and integrated switch silicon that supports load balancing, priority queues, packet classification, and flow control to enable strict bandwidth management for implemented applications.
-
product
Test Fixture
16047E
Perform impedance evaluation of lead type devices of up to 120 MHz; includes a guard and a shorting plate
-
product
Compact EMS/EMI Test Platform
CEMS100
Setting up an EMS/EMI test system is a very complex process requiring significant investment. The steps involved include custom planning, design, installation and configuration of various components and standalone instruments as well as the RF shielded anechoic chamber. Rohde & Schwarz offers the standardized R&S®CEMS100 test platform that is the company's first flexible, reliable and cost-effective off-the-shelf solution for radiated EMS measurements in line with IEC/EN 61000-4-3.
-
product
Ethernet and Fibre Channel Test Platform
SierraNet M1288
The SierraNet M1288 Ethernet and Fibre Channel test platform provides best in class analysis, jamming and generation for traffic capture and manipulation for testing application and link characteristics. SierraNet M1288 is the latest in the line of industry leading test and measurement tools from Teledyne LeCroy, designed for today’s high-speed storage and communications fabrics. SierraNet M1288 supports examination and modification of Ethernet and Fibre Channel links utilizing both Pulse Amplitude Modulation 4 (PAM4) and legacy Non-Return to Zero (NRZ) technologies.
-
product
PXI Dual 2 x 2 Fibre Optic (M Mode) ST M50
40-860-522-M50
Pickering PXI Fiber Optic MEMS Switching cards are available in many high density formats with a choice of 5 different connector styles to suit most applications: FC/APC (for optimal performance), FC/PC and SC/PC for general applications and LC and MU for high density applications. Fiber optic multiplexers create a signal path by redirecting the optical signal into a selected output fiber. This is achieved using Micro-Mechanical Mirrors driven by a highly precise mechanism and activated via an electrical control signal.
