Motion Simulation
-
Product
PXI Analog Output/Current Loop Simulator Module - 12 Channel
41-765-002
Analog Output Module
The 41/43-765-002 is a 12-channel Analog Output Module designed to meet the requirements of industrial control applications utilizing current loops 4 – 20mA. It consists of up to four 16-bit, digital-to-analogue converters (DAC), capable of creating four current outputs each. Output current within 0mA - 4mA and 20mA - 24mA, give the ability to simulate error or extra signaling conditions. The ±24mA mode gives the ability to simulate either sourcing or sinking sensor.
-
Product
Interference Simulation System
GSS7765
-
Combined with Spirent’s powerful GSS7000 or GSS9000 Series simulators, the GSS7765 interference generator creates the ultimate tool for testing against external jamming and unintentional interference. The GSS7765 enables you to create and generate custom waveforms, helping you to defend your systems against real-world threats.
-
Product
Value DSP-Based 8-Axis Motion Control Universal PCI Card
PCI-1285V
-
Encoder input is 10 MHz for 4xAB mode, 2.5 MHz for CW/CCW modePulse output up to 5 MppsSupports linear and circular interpolationHardware emergency inputSupports E-GearSupports programmable acceleration/deceleration rateMemory buffer (10K points) for trajectory planning which is designed in DSP(Auto-blending is not supported)Position compares triggering up to 100 KHz, and memory buffer is up to 100 K points in DSPPosition latchProgrammable interrupt and watchdog timerRDY/LTC-dedicated input channels & SVON/CMP/CAM-DO/ERC-dedicated output channels are switchable for general input and output purposes
-
Product
Simulation and Model-Based Design
Simulink
-
Simulink is a block diagram environment for multidomain simulation and Model-Based Design. It supports system-level design, simulation, automatic code generation, and continuous test and verification of embedded systems. Simulink provides a graphical editor, customizable block libraries, and solvers for modeling and simulating dynamic systems. It is integrated with MATLAB, enabling you to incorporate MATLAB algorithms into models and export simulation results to MATLAB for further analysis.
-
Product
4 Port BRI-S/T-U ISDN Simulator
BRI-2U2ST
-
The unit has two S/T and two U ports allowing ISDN basic rate terminal equipment to be connected together just as if they were connected through the ISDN network.
-
Product
ARINC 429 PXI Express Test & Simulation Instrument
PXIe-C429
-
Avionics Interface Technologies
16, 32, or 64 ARINC 429 Channels (up to 32 Tx & 32 Rx) - Programmable Tx channel output amplitude - Programmable High/Low Speed Operation - Eight (8) Discrete I/O (Four (4) inputs, and four (4) outputs) - Concurrent operation of all Tx/Rx Channels at high data rates - Full error injection and detection • Data capture filtering, 100% bus recording, and physical bus replay - Rate-oriented Label Transmission - Label Selective Trigger for Capture/Filtering - IRIG-B time code encoder/decoder with free-wheeling mode - Application Interface supporting C/C++, C# and VB.NET Development - Device driver support: Windows, Linux, LabVIEW Real-Time (others on request) - Compatible with AIT’s Flight Simulyzer GUI Bus Analyzer Software
-
Product
Cell Solar Simulator
QuickSun® 130E
-
QuickSun 130E exceeds the ordinary Class A criterions of IEC904-9 ed. 2 with clear margin providing enhanced IV characteristics accuracy. The applicable test methods and procedures are inspected by SGS Fimko Ltd in order to guarantee the compliance and traceability not only with the above standard but also with IEC904-1 ed. 2 which specifies the IV measurement conditions.
-
Product
3U VPX RL Thermal Load Simulation Module
-
The 3U power test module is an ideal solution for evaluating heat dissipation in a rugged conduction cooled VPX cage or chassis. This card is a thermal load in the chassis to evaluate the heat dissipation. The chassis can be monitored with temp sensing probes and or FLIR imaging. Different wattages are selected by setting dip switches. The +5 and 3.3V loads are on the top of the module. The +12V and -12V loads are on the bottom side of the module.
-
Product
Acceleration Simulation Mode (ASM) for Single Driven Axle Vehicles
ASM_AF | VP 230045
-
Maschinenbau Haldenwang GmbH & Co. KG.
The ASM-AF roller set is used in test centres and is suitable for vehicles with a single driven axle. It was designed for the exact measurement of the exhaust gas behaviour of vehicles during their transient emission test and permits a driving resistance simulation for the exhaust gas tests ASM-5015 and ASM-2525 (Acceleration Simulation Mode) in accordance with the specifications BAR '97. The ASM-AF is built into the base.
-
Product
Solar Simulator
-
It is the optimum light source for the evaluation of requiring high degree of parallelism close to sunlight. Irradiation area and parallelism are produced according to your request.
-
Product
Seal Integrity Verification and High Altitude Shipping Simulator
SIV III
-
The SIV also has the ability to simulate shipping a packaged box of dry goods at high altitudes. The number of peaks, the heights of the inclines (or peak), the ramp speed (or rate), and the time at the peak are configurable through the controller.
-
Product
Linear Motion Speedometer
ST-1210
-
The ST-1210 linear motion speedometer measures the passing time between the specified two points, and calculates the passing speed using the distance between the two points and the measured passing time. Useful to measure the plunger speed of an injection cylinder and the passing speed of open/close sections (doors) of the vehicle, and the passing speed of the vehicle with a high precision.
-
Product
Battery Cell Simulator
BCS-LABCAR
-
The ETAS Battery Cell Simulator (BCS-LABCAR) is a Hardware-in-the-Loop system which specifically targets the signal-level test, validation, and calibration of battery management systems (BMSs). The BCS-LABCAR is a high-precision Battery Cell Simulator that emulates the behavior of individual battery cells and packs across a wide range of challenging operating conditions, e.g. cell balancing over-charging, deep discharging, or pulse operation. The system is highly modular and thus scalable to emulate battery packs from a single cell all the way up to 200 cells.
-
Product
0.30° Accuracy Roll & Pitch Dynamic Motion Sensor
DMS-RP30
-
The DMS range of motion sensors is designed specifically for the motion measurement needs of the marine industry. Whether it is achieving IHO standard survey from any size of vessel, or providing safety critical monitoring of offshore platforms, large vessels, helicopter landing decks, cranes and positioning systems, the DMS provides accurate motion measurement in all sea conditions. Incorporating an enhanced external velocity and heading aiding algorithm for improved accuracy during dynamic manoeuvres, the solid state angular rate sensors offer reliability in the highest performing vertical reference units ever produced by TSS.
-
Product
Single Long Pulse Solar Simulator & I-V Test System
TriSOL SLPSS
-
The OAI Test System for HIGH EFFICIENCY SOLAR CELLS overcomes the limitations of flash testing by providing a highly optimized pulse width and voltage sweep rate to match the cell’s dielectric response speed. As a result, the system produces extremely accurate measurements of solar cell efficiency leading to increased profitability.
-
Product
Modbus Simulator & Tester
Modbus Poll
-
Modbus Poll is a Modbus master simulator designed primarily to help developers of Modbus slave devices or others that want to test and simulate the Modbus protocol. With the multiple document interface you can monitor several Modbus slaves and/or data areas at the same time. For each window you simply specify the Modbus slave ID, function, address, size and poll rate.
-
Product
Panel-mounted Power Amplifier(Hardware In The Loop Simulation)
PA30Bi
-
PA30Bi is the panel-mounted type real time simulation amplifier with three-phase current and four-phase voltage.
-
Product
2 PRI + 32 BRI-U ISDN Simulator
CH-32BRI-U-MOD-2PRI
-
This unit has two PRI ports and 32 BRI ports allowing ISDN equipment to be connected together just as if they were connected through the ISDN network
-
-
Product
Link simulation to ATE conversion
VCD2ATE
-
VCD2ATECost effective link simulation to ATE conversionDirect conversion from event driven design simulation dump (VCD/EVCD) to specific tester program files. VCD/eVCD to tester conversion Simple and cost effective conversion solution Simple cycle definition in excel High Performance Fast run time Handles very large files >6Gb
-
Product
MIMIC® IOS Simulator
-
MIMIC IOS Simulator is a command line simulator that fully supports Cisco IOS® software as well as NX-OS, JUNOS, NETCONF, other command line interfaces and SNMPv1, v2, v2c, v3. You can simulate up to 100,000 devices in a single workstation, and an unlimited number of devices can be simulated by distributing it over multiple workstations. You can access devices using Telnet, SSH and SNMP. Changes made using one protocol is reflected in the other.
-
Product
PCB Simulation Solutions for High-Performance Designs
HyperLynx
-
HyperLynx® offers a complete suite of analysis and verification software that meets the needs of PCB engineers at any point in the board design flow. Easy to use and integrate into your flow, HyperLynx equips PCB engineers to efficiently analyze, solve and verify critical requirements to avoid costly re-spins. Achieve greater innovation, faster time-to-market and decreased costs with HyperLynx.
-
Product
Environmental Simulation
-
Simulation of environment. PHOENIX TESTLAB's environmental simulation laboratory is accredited for environmental testing of a multitude of standards.
-
Product
Full DSP-Based 4-Axis Motion Control Universal PCI Card
PCI-1245
PCI Card
Encoder input is 10 MHz for 4xAB mode, 2.5 MHz for CW/CCW modePulse output up to 5 MppsMemory buffer (10K points) for trajectory planning which is designed in DSPSupports E-Gear, and helical interpolationSupports E-CAM providing 256 points to describe the CAM profiles which buffers located in DSPHardware emergency inputWatchdog timerPosition latch via ORG & index signalPosition compare triggering up to 100 KHz, and memory buffer is up to 100K points in DSPProgrammable interruptSupports gantry mode by semi-closed loop pulse train controlRDY/LTC-dedicated input channels & SVON/CMP/CAM-DO/ERC-dedicated output channels are switchable for general input and output purposes
-
Product
GNSS Simulator
NCS NOVA
-
The NCS NOVA is IFEN´s newest RF signal generator technology based on a modular and highly flexible Software Defined Radio (SDR) platform. This flexibility makes the NCS NOVA the ideal choice for a wide range of test applications.The NCS NOVA`s full upgradeability makes it a future-proof investment for the upcoming multi-frequency era in commercial and professional applications. It is far more than just a GPS/GNSS Simulator!
-
Product
AC Load Simulating Inductors
-
Osborne designs our AC Inductors to provide the desired inductance and to perform effectively with the dissipation characteristics presented to the circuit. Dissipation characteristics depend on circuit current and operating frequency. The Osborne design approach is unique to the extent that we design for frequency effects. The resulting inductors deliver superior performance.
-
Product
Motion, Temperature And Leak Detection Sensors
-
Select from a wide range of motion and temperature sensors for motion detection, temperature, humidity, and carbon dioxide (CO2). We carry passive infrared (PIR) sensors that detects human-body generated infrared waves to indoor motion detection. They can be configured to automatically switch on a light or trigger alarms if motion is detected. The DL-300 can also be used on mobile devices so it is easy for you to monitor your room temperature, humidity, carbon dioxide (CO2) and mono dioxide (CO) level on your phone.
-
Product
Modular Solar Array Simulators
E4360 Series
-
The E4360 Modular Solar Array Simulators accurately simulates the I-V curve of different arrays under various environmental conditions (such as eclipse, spin, rotation, age and temperature). Its small size and high power saves valuable rack space.
-
Product
Walk in Chamber for Altitude Simulated Test
-
Guangdong Bell Experiment Equipment Co.,Ltd
Walk in Chamber for Altitude Simulated Test Relative Standard test requirementsTest Object: battery pack and systemTest Conditions: Altitude 4000m or the equate air pressure condition, atroom temperature.The test objects stay in the test condition as Item 2 for 5 hours.Subject the test object to 1C(no more than 400A) constant current discharge until reaching the cutoff condition.After testing, observe for 2h under the room temperature.
-
Product
Motion Controllers
-
Curtiss-Wright Defense Solutions
Motion control systems for defense applications must be two things - accurate and reliable. As the brains of these systems, motion controllers are responsible for ensuring all other system components are just that, no matter the conditions.
