Showing results: 61 - 75 of 101 items found.
-
PMC-MC-X4 -
Dynamic Engineering
The PMC-MC-X4 adapter / carrier converter card provides the ability to install up to 4 (four) PMC cards into a small enclosure. The PMC-MC-X4 has two PMC card slots mounted front and rear to create a compact arrangement with 4 PMC slots. Suitable for 32/64 with 33/ 66 MHz bus operation.
-
PMC-BiSerial II -
Dynamic Engineering
The PMC BiSerial has been updated to be even better. Building on the knowledge and experience gathered from multiple IP and PMC BiSerial implementations and adding in the latest technology has created the PMC-BiSerial-II. The BiSerial II features completely isolated FIFOs with 32 bit ports for increased adaptability and performance.
-
PMC-BiSerial III -
Dynamic Engineering
The PMC BiSerial family has been updated to include a Spartan III [Xilinx] based card with expanded capabilities.. Building on the knowledge and experience gathered from multiple IP and PMC BiSerial implementations and adding in the latest technology has created the PMC-BiSerial-III. The BiSerial III features completely isolated FIFOs with 32 bit ports for increased adaptability and performance.
-
Dynamic Engineering
PMC-ExtendIO-II provides a 32/33 - 64/66 extension between a PMC and Host. Any combination of PMC PCI bus speed and data width can be accomodated. With 66 MHz implementations cable lengths may be restricted compared to 33 MHz usage.
-
PIM-Carrier-6U -
Dynamic Engineering
The PMC Carrier routes the PMC IO from P04/P14 to J3/J5. PIM-Carrier-6U routes the IO from J3/J5 to the two PIM positions. The PIMs route the IO to the bezel providing the equivalent of PMC front bezel IO on the rear of the chassis.
-
Dynamic Engineering
PMC-Parallel-IO provides 64 independent IO in one PMC slot. 64 mA open drain buffers on each IO. Two interrupt sources. External or internal clock reference. Custom state machine designs.
-
Dynamic Engineering
The PMC-Serial is capable of providing multiple serial protocols, both synchronous and asynchronous with a wide range of baud rates. The PMC-Serial has up to 8 UART channels, and two SCC channels. The protocol processors are complemented with a variety of IO which can be selected as a build option. RS-232, RS-485, RS-422, and RS-423 are supported. Two enhanced hysteresis MIL STD 188-114A receivers, and two open drain active low output drivers are also provided.
-
Dynamic Engineering
PMC SpaceWire implements SpaceWire in a convenient PMC format. With PMC you can install the adapter into PCI [PCIBPMC], cPCI [cPCI2PMC], or processor board pmc slots. The SpaceWire specification calls for LVDS signaling and a specific 9 pin micro-D connector. You can connect the PMC-SpaceWire to other SpaceWire compliant devices without electrical interface issues
-
PMC2PCI -
Dynamic Engineering
The PMC2PCI ( PMC to PCI ) adapter / carrier converter card provides the ability to install a PCI card into a standard PMC slot. The PMC2PCI has two PCI card slots mounted to a PMC card. One slot can be used at a time with the choice of 3V or 5V IO and 32 or 64 bit data paths.
-
Dynamic Engineering
The PMC-XM is intended for use in situations where the user wants to control the design. PMC-XM has two FPGA devices built in. The first device takes care of the PCI interface, DMA etc. The second device [Virtex XC4VSX35-10] is for the user application. The Transition Module [XM] is attached to the Virtex device.
-
PMC-Extend-IO -
Dynamic Engineering
PMC-ExtendIO-II provides a 32/33 - 64/66 extension between a PMC and Host. Any combination of PMC PCI bus speed and data width can be accomodated. With 66 MHz implementations cable lengths may be restricted compared to 33 MHz usage.
-
HDRterm50 -
Dynamic Engineering
Ribbon cable headers are commonly used with IP compatible hardware. Ribbon cable is difficult to connect to other hardware, especially if multiple destinations are involved. The HDRterm50 converts from 50 pin ribbon cable to a 50 pin terminal strip. Discrete wires are easily connected with the screw locks on the terminal strip.
-
DINterm64 -
Dynamic Engineering
Ribbon cable headers are commonly used with VME compatible hardware. Ribbon cable is difficult to connect to other hardware, especially if multiple destinations are involved. The DINterm64 converts from 64 pin ribbon cable to a 64 pin terminal strip. Discrete wires are easily connected with the screw locks on the terminal strip.
-
Dynamic Engineering
The Stand Alone Relay accepts a regular PC style power connector that powers two relays. Upon power failure, the relays disengage the two ethernet lines so as to not interrupt communication on the ethernet lines. A CPLD allows for pass through and bypass of Ethernet signals. 10/100 Ethernet compatible. The CPLD is controlled via user input.
-
IP-429-II -
Dynamic Engineering
Connect to your Avionics with IP-429. Pick 2,4,6,or 8 ARINC 429 compatible receivers and 1, 2, 3, or 4 transmitters. Transorb protected IO. Software programmable transmit rates [100K or 12.5K]. Time Tag on received data. IndustryPack campatible with 8 or 32 Mhz. bus operation.