Dynamic Engineering
Dynamic Engineering products are designed and manufactured in the USA. The majority of assembly work is done in our state-of-the-art manufacturing facility in California. Since 1988 we have developed engineering, purchasing, assembly, and test capabilities to guarantee reliability in our products. This is evidenced by our AS9100 and ISO9001 certifications. Dynamic Engineering has a wide product line with embedded solutions for PCIe, PCI, PMC, XMC, IndustryPack, cPCI, cPCIe, PCI-104, PC104e, VME and VPX. We also work with custom requirements. Solutions include adapters/carriers to install one embedded format [i.e. PMC] into another [i.e. PCIe], utilizing available positions in current systems with existing or upgraded hardware. Other solutions include standard bus interfaces for example: SpaceWire, 1553, and HOTLink. Custom designs are frequently implemented for special purpose buses and interfaces. Additionally, Dynamic Engineering provides chassis, power supplies, backplanes, breakouts, cables and other support functions to complete each solution. Drivers, reference SW and applications are supported for Windows, and Linux. For information on specific products please visit our website
- 831 457 8891
- sales@dyneng.com
- 150 Dubois St.
Suite B&C
Santa Cruz, CA 95060
United States of America
-
Product
PCIe Module with Sparta FPGA
PCIe-BiSerial-DB37
-
Building on the knowledge and experience gathered from multiple IP, PMC, PCI-104, and PC104e based BiSerial implementations helped Dynamic Engineering to create PCIe-BiSerial-DB37. PCIe-BiSerial-DB37 features completely isolated FIFOs with 32 bit ports for increased adaptability and performance.
-
Product
IP-QuadUART-485
-
The IndustryPack compatible IP-QuadUART-485 design integrates a quad UART onto an IndustryPack module. The UART (16C854) features 128 byte FIFOs for RX and TX ports on each channel. The UART is supported by an advanced IP module interface implemented within a Xilinx FPGA.
-
Product
IP-BiSerial-IO
-
The serial Input and Output channels are highly programmable and fully independent. The standard interface offers Data, Clock and Strobe. The programmable output rates and a user oscillator position allow for flexible frequency selection. The adaptable interface allows for bursted or continuous operation, and all kinds of data / handshake protocols.
-
Product
Multi-Functional Board
PCI - HARPOON
-
PCI-Harpoon is a multi-functional board with capabilites for isolated measurement and control. The initial use of the PCI-Harpoon is to simulate - act as if the PCI-Harpoon was another piece of equipment. The simulation provides a means to test the rest of the equipment without requiring the real [expensive] asset. In addition the PCI-Harpoon can provide status and direct software control of the system.
-
Product
PIM-Parallel-IO
-
The PIM-Parallel-IO facilitates rear panel IO in cPCI based systems using PMC's. The PIM-Parallel-IO provides the PMC_Parallel_IO front panel IO where rear panel IO is desired. The PIM-Parallel-IO can be used with other PMCs as well.
-
Product
PCI Card with input channels
PCI_LVDS_8R
-
The PCI_LVDS_8R has 8 channels of LVDS input. The channels are grouped two per Filter Xilinx. The input data is filtered, then written to the Input FIFO. There is one Input FIFO per LVDS channel. 1K x 32. One Latch Xilinx handles 4 LVDS channels. The data is read from the Input FIFO by the Latch Xilinx and either written to the SDRAM or the Output FIFO.
-
Product
IP-QuadUART
-
IP Module with quad UART capability. 128 byte FIFOs, 8 & 32 MHz operation, RS232 and RS422/RS485 interface, programmable terminations, 1.5MHz - 100 Hz.
-
Product
CompactPCI
cPCI4IP
-
The cPCI [CompactPCI] compatible cPCI4IP design adds 4 Industrypack compatible slots to your cPCI host. The cPCI4IP acts as an adapter, converter, carrier, or bridge between the cPCI bus and your IndustryPack hardware. The cPCI4IP is a 6U 4HP cPCI design with 4 IP slots.
-
Product
PMC Carrier/Adapter/Motherboard
PMC-MC-X2-RIO
-
PMC-MC-X2-RIO adapter, carrier, motherboard provides the ability to install up to 2 (two) PMC modules into a small enclosure. PMC-MC-X2-RIO has one PMC card positions top and bottom to create a compact arrangement with 2 PMC positions.
-
Product
PMC-XM
-
The PMC-XM is intended for use in situations where the user wants to control the design. PMC-XM has two FPGA devices built in. The first device takes care of the PCI interface, DMA etc. The second device [Virtex XC4VSX35-10] is for the user application. The Transition Module [XM] is attached to the Virtex device.
-
Product
PMC-ExtendIO-II
-
PMC-ExtendIO-II provides a 32/33 - 64/66 extension between a PMC and Host. Any combination of PMC PCI bus speed and data width can be accomodated. With 66 MHz implementations cable lengths may be restricted compared to 33 MHz usage.
-
Product
High Density 68 pin
HDEterm68
-
The high density 68 pin SCSI II/III connector is being used for purposes other than SCSI interfaces because of board and front panel space limitations. For example in the PMC environment the SCSI connector provides an excellent size and pin count for the front panel space allowed. The SCSI connector while dense, is not easy to connect to with wiring intended to go to multiple locations
-
Product
IndustryPack system trouble shooter
IP-DEBUG-IO II
-
IndustryPack system trouble shooter providing testpoints on all of the IP IO signals. Loop back is as easy as wire-wrap. Custom feedback signals are supported with socket and power connector support. Now with 2 ribbon cable connectors to support in system debugging.
-
Product
PCIe adapter for PMC
PCIeBPMCX1
-
Now you can use your PMC with a new PC. The new PC´s have PCI Express connectors in larger quantities than PCI slots. The PCIeBPMCX1 ( PCIe Bridge PMC 1 slot) adapter / carrier converter card provides the ability to install one PMC card into a standard PCIe (Express) 4 lane slot.
-
Product
PMC-BiSerial II-NG1
-
The PMC BiSerial-II NG1 is part of the PMC Module family of modular I/O components by Dynamic Engineering. The PMC BiSerial-II is capable of providing multiple serial protocols. The NG1 protocol implemented provides two full-duplex RS-422 UART interfaces with error detection, two half-duplex RS-485 custom "index" interfaces, external clock input, two clock outputs, and various discrete signal inputs and outputs, all using RS-485 transceivers
