Dynamic Engineering
Dynamic Engineering products are designed and manufactured in the USA. The majority of assembly work is done in our state-of-the-art manufacturing facility in California. Since 1988 we have developed engineering, purchasing, assembly, and test capabilities to guarantee reliability in our products. This is evidenced by our AS9100 and ISO9001 certifications. Dynamic Engineering has a wide product line with embedded solutions for PCIe, PCI, PMC, XMC, IndustryPack, cPCI, cPCIe, PCI-104, PC104e, VME and VPX. We also work with custom requirements. Solutions include adapters/carriers to install one embedded format [i.e. PMC] into another [i.e. PCIe], utilizing available positions in current systems with existing or upgraded hardware. Other solutions include standard bus interfaces for example: SpaceWire, 1553, and HOTLink. Custom designs are frequently implemented for special purpose buses and interfaces. Additionally, Dynamic Engineering provides chassis, power supplies, backplanes, breakouts, cables and other support functions to complete each solution. Drivers, reference SW and applications are supported for Windows, and Linux. For information on specific products please visit our website
- 831 457 8891
- sales@dyneng.com
- 150 Dubois St.
Suite B&C
Santa Cruz, CA 95060
United States of America
-
Product
PMC-Parallel-485
-
The PMC compatible PMC-Parallel-485 design adds 32 [RS-485 /RS-422] differential IO lines to one slot of your carrier board. 2 additional differential pairs are available for a clock & clock enable. The signals can be used to capture data with an external reference or programmed to be references for the rest of the system.
-
Product
cPCI to PMC Compatible Adapter/Carrier
cPCIBPMC6UET
-
cPCIBPMC6UET ( cPCI to PMC ) adapter / carrier converter card provides the ability to install up to two PMC cards into a standard cPCI slot. cPCIBPMC6UET has two PMC card slots mounted to a universal voltage 6U 4HP cPCI card.
-
Product
IP-QuadUART-485
-
The IndustryPack compatible IP-QuadUART-485 design integrates a quad UART onto an IndustryPack module. The UART (16C854) features 128 byte FIFOs for RX and TX ports on each channel. The UART is supported by an advanced IP module interface implemented within a Xilinx FPGA.
-
Product
PCIe Adapter for VPX
PCIe8LSwVPX3U
-
PCIe8LSwVPX3U is an 8 lane PCIe adapter with switch isolation for VPX development. The switch isolates the spread spectrum clocking found in most PC´s from the VPX port. PCIe 3.0 compliant, 1-8 lanes can be used by the installed VPX.
-
Product
IP Module
IP-429
-
ARINC 429 is a versatile standardized bus interface. ARINC 429 is robust featuring Manchester encoding and enough voltage swing to provide excellent noise immunity and reasonable throughput rates. ARINC 429 is the interface of choice for critical applications; for example aircraft instrumentation and control.
-
Product
cPCI and PMC Compatible Adapter Carrier
cPCIBPMC3U64ET
-
By customer request Dynamic Engineering has developed two extended temperature versions of the popular cPCIBPMC design. The design effort included switching to a new bridge to meet the temperature and timing requirements. The new bridge brings new features including the ability to operate the PMC side at a higher clock rate than the cPCI side. The new bridge also has built in features for local address spaces, using the PMC clock in monarch mode for the secondary side, and operating in transparent or non-transparent modes
-
Product
Remote mount PMC
PMC-Extend-IO
-
PMC-ExtendIO-II provides a 32/33 - 64/66 extension between a PMC and Host. Any combination of PMC PCI bus speed and data width can be accomodated. With 66 MHz implementations cable lengths may be restricted compared to 33 MHz usage.
-
Product
PCIexpress
-
Peripheral Component Interconnect Express or PCIe, PCIexpress etc. is a serial interconnect system with bidirectional, and potentially parallel traffic at high speeds. Signalling is encoded for error checking and line loading. There are 3 "Gens" fairly widely in use at this time.
-
Product
PIM-Carrier-Dual
-
The PMC Carrier routes the PMC IO from P14/P24 to J3/J5. The PIM-Carrier-Dual routes the IO from J3/J5 to the two PIM positions. The PIMs route the IO to the bezel providing the equivalent of PMC front bezel IO on the rear of the chassis. The PIM can match the pinout of the front bezel IO to allow for common cables to be used for front and rear IO.
-
Product
PCIe Adapter for XMC
PCIe4LXMCX1
-
Simple and easy to use. Install PCIe4LXMCX1 into your PCIe system to adapt an XMC card. The XMC can have bezel and or rear IO. Pn4 and/or Pn6 are supported with PCIe8LXMCX1. 8 lanes are routed from the PCIe gold fingers to the XMC position. XMC´s with up to 8 lanes can be used. The PCIe lanes to/from the XMC are routed per PCIe specifications with matched lengths and impedance control.
-
Product
PIM-Parallel-IO
-
The PIM-Parallel-IO facilitates rear panel IO in cPCI based systems using PMC's. The PIM-Parallel-IO provides the PMC_Parallel_IO front panel IO where rear panel IO is desired. The PIM-Parallel-IO can be used with other PMCs as well.
-
Product
8 Channel Serial IndustyPack Card
IP-OctalSerial
-
8 channel serial IndustyPack card with 4 dedicated in and 4 dedicated out channels. Each channel has its own seperate FIFO and state machine
-
Product
PCI Module
PCI-ECL-II
-
PCI-ECL-II - with Spartan 6 FPGA, 16Mx32 SDRAM, 20 ECL TX , 20 ECL RX, and 12 TTL IO
-
Product
Specialized Extender Card Testing IP Modules
IP-Debug-Bus
-
IP-Debug-Bus is a specialized extender card which is optimized for testing IP Modules. The bus signals are all accessible via test points. The testpoints include multiple ground locations and .025 sq. posts for ease of connection to your logic analyzer or scope. The testpoints are labeled for easy identification
-
Product
PMC-BiSerial II-NG1
-
The PMC BiSerial-II NG1 is part of the PMC Module family of modular I/O components by Dynamic Engineering. The PMC BiSerial-II is capable of providing multiple serial protocols. The NG1 protocol implemented provides two full-duplex RS-422 UART interfaces with error detection, two half-duplex RS-485 custom "index" interfaces, external clock input, two clock outputs, and various discrete signal inputs and outputs, all using RS-485 transceivers
