6TL Engineering
6TL is a pioneer in applying the modularity concept to the design of Automated Test Equipment for electronics products. FastATE® Technology is the core to developing turn-key solutions that are truly modular, scalable and flexible, and thus we help to make the job of both test engineers and budget managers much easier. Thanks to FastATE, test engineers do not have to address the recurrent tasks of every project: a 6TL module completes these tasks for them. Each module selected is a high-level block that covers a function of the ATE and works together with the rest making in the end a real modular and flexible production test solution. The resulting test solution will be easily documented and will smoothly become the standard for the production, since the standardization is in the genetics of the FastATE® Technology.
- 34 937 270 074
- info@6tlengineering.com
- PASSATGE DE LA NOGUERA, 2
CASTELLAR DE LAS VALLES, BARCELONA 08211
Spain
-
Product
10-Ch Pneumatics CAN without RCV module
YAV90PNF
CAN Interface
This pneumatic subsystem is the same as YAV90PNE, but without the VPC receiver module integrated, making it a good option to be used inside the fixture. Since the control is CAN, user can easily place electrovalves inside the fixture without the need to use a bunch of wires.
-
Product
48-Ch 2A-250VAC 2-Bus Fault Insertion
YAV90076
Fault Insertion Unit
48 channels2A 250V 2 Fault Insertion BusesSwitching up to 60CAN Control (or Ethernet with Ethernet to CAN Gateway)Drivers dll & VIs available
-
Product
64-Ch 1-Bus Fault Insertion
YAV91082
Fault Insertion Unit
64 channels 1 thread 2A 250V 1 Fault Insertion Buses Switching up 60W CAN Control (or Ethernet with Ethernet to CAN Gateway) Drivers dll & VIs available
-
Product
Digital and Analog I/O's
Digital I/O
6TL's line of YAV module digital and analog I/O equipment.
-
Product
POF Ext Ø 1,5mm 600mm, from 5mm Lens to VPC ITA Contact
YAV90CLR10
LED Sensor
The probes for sensing LEDs, P/N YAV90CR10 feature an Optical Head to correct missalignment errors in X and Y axis. As a result, the relative read out will oscillate less tan 5% with a missaligment of + 0,5 mm Offset
-
-
Product
Power Management & MMI Module
H73000700
Interface
This module, named “6TL-MMI”, is designed to be the interface between an operator and a SYSTEM as well as being a metered power distribution unit (PDU) for it. The module is providing also safety controls, data bus interfaces, temperature control and timers. The 6TL-MMI is suitable for any ATE, and specially for those based on CAN bus controlled devices, because in addition to the above functionalities, this module is also providing galvanic isolation up to 1500V for the CAN bus. This isolation will block potential disturbance towards the DUT.
-
Product
Sealed Beam Bulb Testing System
H710019SSL
Test Platform
EOL test for manufacturing of bulbs with LED for applications requiring to ensure watertightness: vehicles, marine, swimming pools, operating rooms, classified areas (Ex Zone), etc. The test system checks in a short time all the light and electrical characteristics of the bulb. A high precision Micro Leakage Meter also checks that there are no leaks between the environment and the inside of the bulb. The test results are recorded on the PC and can be printed on a quality control label attached to each unit.
-
Product
12-Ch 10A-250VAC RCV Power Distribution Unit
YAVAR438
Switch Module
- Hardware controlled Enable Input- 12 Power relays up to 10A 250VAC/DC and 300W or 2.700VA switching power- 12 10-mOhm shunt resistors.- 6 Switched 2-Pole sense channels- Single phase isolated or 3-Phases non-isolated switching capabilities, to or from the device under test (power or load)- VPC TriPaddle 96 pins connector.- NI LabView & TestStand driver.- .NET, C/C++, VB driver.- Soft Front panel for direct interface.- CAN Control or Ethernet (with Ethernet to CAN Gateway).- Self-test module available.- Form A
-
-
Product
In-Line RF Test Station
AP770
RF Test System
ICT, Functional, Hipot, Vision, ISP and RF test with low cost fixtures in a very compact test station footprint Works with PCBs up to 450×550 mm or with palletized devices Space for up to 25 VPC mass interconnect modules or YAV switching units
-
Product
4x (1 to 4) + 1x (4 to 1) 50 Ohm 2.5GHz Mux
YAV91500
Multiplexer Module
5x (1×4) Mux + 2x Pass trough30Vac/dc, 10W MaxMax current 500mACAN Control (or Ethernet with Ethernet to CAN Gateway)Drivers dll & VIs availableReflective
-
Product
RJ45 (Ethernet 100 Base T) to 90 Series Interface
J90RJ45I
Ethernet Interface
RJ45 Ethernet connector for VPC Tripaddle ITA moduleUp to 3 connectors per moduleFor Cat 5 Fast Ethernet cable IEEE 802.3 standard100 Base-T
Related
-
Virginia Panel Corporation
Virginia Panel Corporation (VPC) provides VPC provides Interconnect Solutions that enable simultaneous connection of multiple test and measurement signal types through one modular interface. Designed to accommodate signal, power, RF, thermocouple, pneumatic/vacuum, and fiber optic connector modules in multiple configurations, VPC’s innovative products meet the demands of test & measurement interconnect requirements.
-
Columbia Elektronik AB
COLUMBIA ELEKTRONIK AB is an expert organisation delivering complete test fixturing solutions to the Nordic electronics industry. Having pioneered the Swedish, Norwegian, Finnish and Danish markets back in 1977 we have today an absolute leadership in fixturing and test technology and enjoy a solid, major share of the market. We cover the whole spectra with testsystems, testfixtures, mass interconnect solutions and both hardware and software support and services. We design and produce both our own and vendor delivered testfixtures and mass interconnect solutions for functional and in-circuit test of electronic products and assemblies from component and PCB level to subassemblies and finished products. Columbia excels in all modern fixturing technologies – be it vacuum actuated, mechanical or pneumatic – applied to stand-alone, tester-integrated or inline fixtures.
-
DFT - MG-Products BV
DFT, Designed for Testing. is part of MG-Products and is specialized in the delivery of functional Testfixture solutions from both MG-products and 6TL. DFT also stands for Design For Test, perhaps the most important step in the development process of your product. DFT ensures that your product can be contacted and tested efficiently and reliably.
