Langer EMV-Technik GmbH
Langer EMV-Technik GmbH is a medium-sized electro-technical company which is active in the field of electromagnetic compatibility-related
- +1 888 687 5 687
+49 (0) 351 430093-0 - +49 (0) 351 430093-22
- mail@langer-emv.de
- sales@langer-emv.de
- Nöthnitzer Hang 31
Bannewitz, D-01728
Germany
-
Product
Near Field Micro Probe ICR HV H Field
-
The measurement coil is located vertically in the probe head. The near field probes are run with a positioning system (Langer Scanner).
-
Product
Micro probes 1 MHz up to 6 GHz
MFA 01 set
-
The micro probes are used to measure magnetic fields and they have a high resolution. They measure magnetic fields up to 6 GHz, e.g. at signal conductors (150µm), SMD components (0603-0201) or IC pins. The MFA micro probes are guided by hand. An amplifier stage is integrated into the probe head. The amplifier stage (9V, 100mA) is powered via the Bias tee BT 706. It has an impedance of 50 Ohm. The micro probes are connected via the Bias tee BT 706 to a spectrum analyzer or an oscilloscope. Langer EMV-Technik GmbH includes correction lines in the delivery. With the help of the correction lines the probe output voltage is converted either into the respective magnetic field or to the current which is running through the conductor.
-
Product
IC Tester
ICE1
-
The IC Test System was developed to measure the EMC behavior of circuits (ICs) in the event of targeted field or line-related interference and for measuring emissions. The test IC is tested in function. The test environment ICE1 creates the functional environment of the test IC. The respective measurement task is carried out with the corresponding probe set.
-
Product
Immunity Development System
-
Used for EMI suppression in printed circuit boards during the development phase. The developer can use the E1 set to quickly identify the causes of burst and ESD interference. This allows the developer to design suitable measures to solve the causes of the interference. It can also be used to test the effectiveness of the measures taken.
-
Product
Scanner Probe
RFS set
-
The RFS set consits of three passive near field probes designed for the use in a measurement scanner during the development of E-field and magnetic field. They are designed for frequency ranges of 30 MHz to 3 GHz. The probe heads of the RFS set allow for close measurements needed to correctly localize interference sources on an electronic assembly.
-
Product
Immunity
EFT coupling
-
s used for direct-contact measurements of impulse immunity in IC pins, according to IEC 62215-3 and IEC 61000-4-4.
-
-
Product
MP CI set
-
The MP CI set up to measure coupling impedance is used to determine EMC characteristics of connectors and cables. The coupling inductivity defines the coupling inductance of external disturbance on the shield or on the ground with the desired signals. If the coupling inductivity is considered in the construction set-up and the pin or wire assignment of connectors or cables, then the connectors or cables will be more interference-resistant. The MP CI set-up for measuring coupling impedance can be used for following measurements at connectors or cables: 1. measurement of a single signal (common mode) 2. measurement of a symmetrical signal (common mode) 3. measurement of a symmetrical signal (differential mode)
-
Product
Near Field Microprobe E-field 7 MHz to 3 GHz
ICR E150
-
The near field microprobe is used to measure electric fields at extremely high resolution and sensitivity. The optimal distance to the object being measured is < 1 mm. Due to its small probe head dimension, the probe has to be moved by a manual or automatic positioning system, e.g. Langer-Scanner.
-
Product
Measurement Technology for the Development Stage
-
EMC tools for relative measurements of interference emission of assemblies and devices.
-
Product
Near-Field Probes 100 kHz up to 50 MHz
LF1 set
-
The LF1 near-field probe set consists of 4 shielded near-field probes used during the development process for emission measurement of longwave, medium wave, and shortwave frequencies on electronic devices. The probe heads of the LF1 set are designed for incremental detection of sources of electromagnetic interference on assemblies. First, the electromagnetic interference of the assembly is detected by the LF-R 400 probe from up to 10 cm. Then probes with higher resolution like the LF-B 3, LF-U 5 and LF-U 2.5 are used to more precisely detect any source of interference. The probe heads are designed for taking measurements at single pins and larger components. Near-field probes are small and handy. They have a current attenuating sheath and, therefore, are electrically shielded. They can be connected to a spectrum analyzer or an oscilloscope with a 50 Ω input. The H-field probes do not have an internal terminating resistance of 50 Ω.
-
Product
Near Field Micro Probes ICR HH H Field
-
The measuring coil is horizontally located in the probe head. The near field micro probes are operated with a positioning system (Langer Scanner).
-
Product
Near Field Probes
MFA Family
-
The micro probes allow detailed measurements of high-frequency magnetic fields in the layout, at the smallest SMD components(0603-0201) and at IC pins of printed circuit boards.
-
Product
Optical signal transmission
Digital
-
The fibre optic cable are used to transmit digital signals from the device under test under EFT/burst interference.
-
Product
Measurement Technology for Teaching and Training
-
Is particulary suitable for training and further education. With the disturbance emission model, a variety of different experiments which improves one`s understanding of electromagnetic processes in modern electronic engineering are possible. The coupling mechanisms of disturbance emissions are visualized from their sources to the antenna. The impacts of EMC measures are then easier to understand.At VM 251 the electromagnetic d
