Meltronics Systemtech
Meltronics Systemtech is a product creation company. As a technology solution provider, we offer services and turnkey solutions in the harsh Real Time and Strategic Electronics Domain spanning many industries like avionics, medical, transport, defence & industrial equipments.
- (080)28525400/01/02
- meltronics@meltronicsgroup.com
- 82, 1st Main, 5th Cross, A Block
AECS Layout
Kundalahalli, Bangalore 560037
India
Categories
-
product
RTM Sensor Signal Conditioning Board
MS 3631I
CPCI Rear IO Sensor Signal Conditioning Board is a signal conditioning and interface board for CPCI based Advanced Compute & IO Module (MS3639i). This board primarily focusing on LAOA, RAOA, AOSS (2), DCM (3), PCS (3), RSA (5) & ASA (4) and TAT sensor interface. This card shall handle excitation, conditioning, feedback measurement, power measurement. Card has high resolution Digital POTS, Direct Digital Frequency synthesizers, DAC, Discrete Input and Outputs, Analog measurement circuits for handling all sensor. All interface are brought to two 96 Pin Euro Connector.
-
product
One Wire Communication Board
MS 1727
- Digital serial bus communication with low speed data over a single line, Both signaling and driving power over a same single signal.- Protocol used in small inexpensive devices. Such as digital thermometer, weather instruments, laptop sub module, authenticate system and some cell phone battery packs.- Always master only initiates the communication and in overall in charge of the network.- Bus communicates with master and slave at a low data rate of 12kbps.- All terminals in the network are communicating by half-duplex mode.- Maximum of 255 nodes in each 1-wire network- Each data transaction will start with 480micro second low RESET pulse.
-
product
ASCAN BIOMETER
MS 1304
This system is used for finding eye axial length; cornea thickness and calculating the eye IOL power value. This system has capability of storing 100 patient records and downloading facility. System will work as an ASCAN BIOMETER or ASCAN / PACHYMETER BIOMETER system. System consists of LCD, keypad, RS232C interface for downloading and thermal printer interface. It is a microprocessor-based system. This system uses ultrasound signal for measurements.
-
product
FM Tokenless Transmitter & Receiver
MS 1522
Transmitter and Receiver units are designed to work at 24V DC voltage (nominal) with variation between 19.2 V to 28.8V. The system is designed to work with carrier frequency 1800/2700 Hz and modulated frequency 65Hz/85Hz. For 1800Hz Carrier Frequency RED border is used in Front Panel and for 2700Hz Carrier Frequency BLUE border is used in Front Panel. Maximum power consumed by transmitter and receiver are 1.2W and 8W, respectively. Sense level for receiver is less than –19 dBm and No sense level for receiver is more than –22 dBm with 1mw (0 dBm) transmitter power. The equipment is designed to work satisfactorily with temperature variation from 0°C to 55°C with relative humidity of 95% at 35°C. Suitable test points are provided in the back of the equipment to monitor the necessary parameters.
-
product
PMC Analog Out Board
MS 1821
*Bus Interface:- 32 Bit PCI Bus with PMC Interface*Speed of operation up to 66MHz*Spartan-3AN FPGA based design*32 channel single ended analog Output*Unipolar or bipolar voltage output*Programmable output voltage: 0-5V, 0-10V, 0-10.8V, ±5V, ±10V, ±10.8V and is capable of driving up to +/-20mA*16 bit Resolution*Conversion time 10usec typ*Over current protection*Driver interface for Windows2000/XP/VISTA and LINUX OS*Self Test future
-
product
Voltage Stabilizer
MS 7643
VSTAB is a voltage stabilizer, regulates the incoming supply +28V voltage into the required +15V. The electrical specifications meets MIL704 standard. Over load and short circuit protections are provided. Voltage stabilizer Module is a part of shipborne unit and it is meant for ensuring the power supply of the devices of this unit when fed from DC mains with nominal voltage of 28 V and variations of voltages from minimum 16V to maximum 32 V. The power consumption is 45 watts. The module is subjected to Qualification Tests as per MIL-STD-810G.
-
product
Current Measurement Board
MS 1814
*Maximum DC Voltage Rating: 15V to 75V*Maximum DC Current: 5A*Output Voltage per 1A: 1V*Maximum AC Current: 5A*Operating Temperature: 0°C to 55°C*Storage Temperature: -20°C to +65°C*90% Relative Humidity (Non-condensing)*No. of DC Current Channels: 9*No. of AC Current Channels: 4nos*Maximum AC Voltage Rating: 230VAC*Channel Selection: Through 16 CH Analog MUX*Measurement Error Over Full Temperature Range: 5%*Type of Output: Proportional voltages*Maximum Voltage Drop across Series Resistor Full Scale Measurement: 0.05VDC
-
product
Interface And Load Box
MS 3646I
Interface and Load Box is standard portable 19” rack mountable unit. It is customized unit for single channel tester of IFCC. This unit has cable/harness interface between CPCI System and IFCC LRU. This box also houses all actuator loads and switching circuits.
-
-
product
ARM 9 System on Module
MS 1515
- Processor: LPC3250 processor with ARM 9 core running at 266 MHz SDRAM- Memory: DDR2 256 MB (scalable to 512 MB)- Flash Memory: NAND flash 512 MB- Display & Graphics: Programmable color LCD controller supports up to a TFT interface- Touch screen: Integrated touch screen controller- Network Support: 10/100 Base-T Ethernet PHY- PC Interface: One USB 2.0 high-speed On-the-Go interface- Serial Interfaces: Up to four external UARTs- + CAN 2.0B controller- + Three I2C ports- + Three SPI ports- GPIO: Programmable I/O depending on peripheral requirements- Mechanical: 60 mm wide x 60 mm long x 5.4 mm high
-
product
Ruggedized CPCI Processor Board
MS 1535
Ethernet Port – 2 Channel (1GBPS)MIL1553B – 2 Channel (Dual redundancy)USB – 2RS232 – 4 ChannelsRS422 – 4 ChannelsJTAG – Flash Programming and Debugging
-
product
EMU & Mission Data Programmer
MS 1603
The EMU – MIP programming station is used to program, read and erase mission data of Mirage 2000 Aircraft and it has additional feature of programming the Extended Memory Unit. It has 3 EMU Slots (1 Read only) and 5 Slots (1 Read only).
-
product
Industrial Grade PCI DIO 96 Board
MS 1817
*96 digital input/output lines*Support s all PPI Modes (Mode0, Mode 1 and Mode 2)*5 V TTL/CMOS*Compatible with NI DIO Card*2-wire handshaking capability*Known power-up
-
product
Air Data Computer (ADC) Tester
MS 1122
The ADC tester is used in 2nd line maintenance is to check the functionality of ADC. This unit is a rugged customized hardware based on full functionality test of ADC. The Air Data Computer (ADC) Tester is a fully automated GO/NOGO tester with full functional testing in 2nd line maintenance. This tester is to test ADC at unit level and identify faulty Shop Replaceable Unit (SRU). This tester is also used to carry out PI checks on ADC before clear them for installation on aircraft. ADC Interface board designed to test full functionality of ADC. The Air Data Computer (ADC) test equipment shall be used for testing ADC of Tejas Aircraft. ADC test equipment shall verify the functionality against specifications during second line maintenance and pre-installation on the aircraft.
-
