Meltronics Systemtech
Meltronics Systemtech is a product creation company. As a technology solution provider, we offer services and turnkey solutions in the harsh Real Time and Strategic Electronics Domain spanning many industries like avionics, medical, transport, defence & industrial equipments.
- (080)28525400/01/02
- meltronics@meltronicsgroup.com
- 82, 1st Main, 5th Cross, A Block
AECS Layout
Kundalahalli, Bangalore 560037
India
-
-
-
Product
Multi Output Buffer Unit
MS 1632
-
The Multi Output Buffer Unit is used for driving singe input to 32 outputs. This unit drives an analog input to two different 16 set of outputs through two 50 Pin standard D Type connector. The unit works on standard 230V AC.
-
Product
ESI Test Jig
MS 1543
-
This Test System designed to test the analog, discrete, Ethernet, RS232, RS422, Synchro /Resolver and SPI Signals. It is standalone test equipment and has GUI ATP Software interface with laptop/PC through RS232/Ethernet Interface.
-
Product
Bus Isolation Board
MS 1705
-
- Bus Interface - ISA96 Bus, 6U form factor- 16-bit Data Bus- 20-bit Address Bus & Control Signals- Isolated Bus Interface- Driver interface for Windows2000/XP/VISTA and LINUX OS
-
Product
Voltage Stabilizer
MS 7643
-
VSTAB is a voltage stabilizer, regulates the incoming supply +28V voltage into the required +15V. The electrical specifications meets MIL704 standard. Over load and short circuit protections are provided. Voltage stabilizer Module is a part of shipborne unit and it is meant for ensuring the power supply of the devices of this unit when fed from DC mains with nominal voltage of 28 V and variations of voltages from minimum 16V to maximum 32 V. The power consumption is 45 watts. The module is subjected to Qualification Tests as per MIL-STD-810G.
-
Product
Airborne Receiver
MS 2015
-
Receiver shall receive the telemetry signal transmitted by the airborne TGS unit. This unit is a single conversion super heterodyne FM receiver operating at 1486.5MHz. This unit has four connectors. They are RF input connector (J1), Power connector (J2), Signal connector (J3) for AGC signal and a Video output connector (J4). This unit operates at 28V DC and consumes a typical power of 5.6 watts.
-
Product
CAN Interface Board
-
- Auto Learning for slow detection and easy commissioning.- Encoder signal for floor detection.- Detail diagnostic of individual components ensures safety and reliable operation- Attached ARD for each panel for rescue in case of power fail.- Intelligent algorithm to attend any calls within 10 seconds for standard configuration.- VIP option, Fireman switch, overload protection $ protection of all other standard interfaces integrated.- Announciator is integrated with Gong bell.- Preferable selection of floor by user, software functional options, Delay times and important configurations.- Error diagnosis by PC interfaces, eleavator error history and services details make your maintenance job very effective and efficient in time period
-
Product
C012 Communication Board
MS 1728/29
-
- Suitable for standard desktops- Four channel in single board- Up to 10 Mbits/sec operating speed- Low Cost solution- Standard INMOS link protocol- Communicates with transputers- Converts between serial link and parallel bus- Tristate bidirectional bus interface- Memory mapped registers- Interrupt capability- TTL compatibility
-
Product
Fuel Display Unit Tester
MS 1125
-
Fuel Display Unit Test Bench is a compact table-top test bench with front panel controls, indications, built-in signal simulator and necessary power supply for testing the serviceability of Fuel Display Unit of Helicopter. FTB operates on 230 V AC and supplies 28 V DC power to FDU. FTB is housed in a metallic cabinet FTB interfaces with both 61 Pin connector and 6-pin socket mounted on the rear panel of FDU by means of the cable connected to the unit. FTB is fabricated utilizing off-the-shelf standard industrial/commercial components like rotary switches, toggle switches, press switches, test sockets, fuse holders, potentiometer etc. The Frequency generation circuit is integrated into FTB for the simulation of Fuel probe and flow rate signals. The frequency of the signal can be selected by means of a rotary switch Low amplitude sine wave signal is simulated for testing flow rates. Variable voltage DC power supply with a voltage range of 24 to 29 Volts is provided within FTB to power-up FDU. 5 V DC is provided for the operation of signal generating circuit (PIC Frequency Controller Board). An off-the-shelf Hand held battery operated Digital Multimeter (DMM) procured from the prominent manufacturer (FLUKE) is supplied with FTB for setting up and measurement of various parameters like Resistance, Voltage, Frequency etc.
-
Product
MICROBLAZE Processor Board
MS 1536
-
- Virtex 4 FPGA with Embedded PowerPC 405 (PPC405) Core- Up to 450 MHz operation- Tri-mode Ethernet Media Access Controller- A/D Converter Blocks (10-bit / 200 kilo samples per second)- Select IO Technology (Wide selections of I/O standards from 1.5V to 3.3V)- DDR2 SDRAM (256MByte)- Program Storage Flash Memory (8MByte)- Data Storage Flash Memory (8MByte)- Vertex-4 FPGA PROM (4MByte)
-
Product
Audio Board
MS 1813
-
*Two Audio Output Channels (Playback)*Two Audio Input Channels (Recording)*High performance Stereo Audio Codec*PCI Bus Interface
-
Product
RTM Digital & Analog IO Board
-
*Bus Interface:- 16 Bit Data bus, 8 Bit Address Bus*Spartan-3AN FPGA based design
-
Product
Navigation Aid Panel Tester
MS 1114
-
The TE-247 is 19” rack mountable test equipment used for the functional acceptance of NAP-82 and CIP-82 of Jaguar aircraft LRU’s. Microprocessor Based design and MIL1553B Bus, RS232 interface used for testing LRU’s
-
Product
Blanking Signal Generator II
MS 1609
-
This System used for generating continuous and pulsed variable power outputs (Voltage).
