Chroma Systems Solutions, Inc.

Product

Programmable AC Power Source

6400

-

Chroma Systems Solutions, Inc.

6400 - Chroma Systems Solutions, Inc.

The Chroma 6400 series Programmable AC Power Source uses state of the art PWM technology to deliver pure, instrument grade AC power at a very low cost never achieved before. The 6400 AC power source offers maximum rated power for any output voltage from 0 to 300VAC, at any frequency from 45 to 1K Hz. It is not only suitable for commercial applications (47-63Hz), but also for avionics, marine, military applications at 400Hz.

Product

High Frequency LCR Meters Up To 30MHz

Chroma 11050

-

Chroma Systems Solutions, Inc.

Chroma 11050 - Chroma Systems Solutions, Inc.

Measurement capabilities cover the primary and secondary parameters required for testing the inductance, capacitance, resistance, quality factor and loss factor of passive components

Product

Milliohm Meters

Chroma 16502

-

Chroma Systems Solutions, Inc.

Chroma 16502 - Chroma Systems Solutions, Inc.

With a basic accuracy of 0.05%, Chroma 16502 offers a 0.001mΩ ~1.9999MΩ wide measurement range. It provides measurement range with 4 1/2 digits resolution. The fast measurement time is 65 ms. It suits component evaluation on production line. Pulsed test current output mode is used to reduce thermal EMFs affection on milliohm measurement. DC test current output mode is used to fasten measurement speed for inductive DUT. Dry-circuit test current output mode is used to measure such contact resistances where the maximum open-circuit voltage must be limited to 20mV.

Product

Modular DC Electronic Load LED Simulator

6310/A

-

Chroma Systems Solutions, Inc.

6310/A - Chroma Systems Solutions, Inc.

Chroma 6310A Programmable Electronic Load integrates microprocessor capabilities into each load module and mainframe to provide simple and accurate parallel operation to optimize the speed and control among multiple load modules. All load modules may be configured to work synchronously, to test multiple outputs simultaneously, thus simulating real life applications.

Product

Programmable AC Source

6500

-

Chroma Systems Solutions, Inc.

6500 - Chroma Systems Solutions, Inc.

1200VA ~ 9KVADirect Digital Synthesis (DDS) waveform generationProgrammable voltage, current limit, frequency, phase, and distortion

Product

Partial Discharge Tester

19501-K

-

Chroma Systems Solutions, Inc.

19501-K - Chroma Systems Solutions, Inc.

The Chroma 19501-K Partial Discharge Tester is an instrument equipped with AC hipot test and partial discharge detection functions, providing 0.1kV~10kV of AC output, 0.01μA~ 300μA of leakage current, and 1pC~2000pC partial discharge detect ion range for measurement. Chroma 19501-K Partial Discharge Tester is compliant to the IEC60270-1 standard in particular the partial discharge testing requirements for high voltage.

Product

Ultra-High Stability DC Power Supply

62075H-30N

-

Chroma Systems Solutions, Inc.

62075H-30N - Chroma Systems Solutions, Inc.

Chroma’s new 62075H-30N ultra-high stability DC power supply offers many unique advantages for magnet power supply systems in synchrotron applications. These advantages include an excellent current stability of 1.25mA/0.5 hour and 2.5mA/8 hour, extremely low current ripple of 2.5mA, current reproducible within 10mA, precision setting and readback of output current via 20 bit DAC/24 bit ADC.

Product

Solar Array Simulator DC Power Supply

62000H-S

-

Chroma Systems Solutions, Inc.

62000H-S - Chroma Systems Solutions, Inc.

Solar Array Simulator DC Power Supplies by Chroma provide programmable simulation of Voc (open circuit voltage) up to 1800V and Isc (short circuit current) up to 30A. The 62000S-H series provides an industry leading power density in a small 3U high package. The Solar Array Simulator is highly stable and has a fast transient response design, which are both advantages to MPPT performance evaluation on PV inverter devices.

Product

Medical System

Sentinel II

-

Chroma Systems Solutions, Inc.

Sentinel II - Chroma Systems Solutions, Inc.

The Sentinel II system provides fully automatic Electrical safety testing to IEC/EN/UL/CSA 60601-1. Sentinel II saves time by scanning patient connections for leakage current without powering down the medical device.

Product

Low Power Programmable AC Source with Transients

61500 Series

-

Chroma Systems Solutions, Inc.

61500 Series - Chroma Systems Solutions, Inc.

Power:500VA (61501)1500VA (61503)2000VA (61504)4000VA (61505)Voltage range: 0-150V/0-300V/AutoCompact size and weight attributable to advance PWM technologyAC+DC output mode for voltage DC offset simulationProgrammable slew rate setting for changing voltage and frequencyLow output impedance for testing IEC 61000-3-2 (61505)Programmable output impedance for testing IEC 61000-3-3LIST, PULSE, STEP mode function for testing power line disturbance (PLD) simulation capabilityIEC 61000-4-11 voltage dips, short and variation simulationHarmonics, inter-harmonics waveform synthesizer for testing IEC 61000-4-13Programmable voltage, current limitComprehensive measurement capability, including current harmonicsHigh output current crest factor, ideal for inrush current testingTurn on, turn off phase angle controlTTL signal which indicates output transientAnalog programmable interface3 units combined to 3-phase power outputEasy-use software for operation and IEC regulation testOptional GPIB and RS-232C interface

Product

Regenerative Grid Simulators 9kVA-15kVA

-

Chroma Systems Solutions, Inc.

Chroma Systems Solutions, Inc.

Four quadrant, single- or three-phase AC power sources designed to simulate real-world grid characteristics for EV, PV inverter, and smart-grid test applications.

Product

Digital MultiMeter

12061

-

Chroma Systems Solutions, Inc.

12061 - Chroma Systems Solutions, Inc.

The 12061 6½ Digital Multimeter has assorted settings for resolution, integration time and ranges that allow users to optimize the configuration of measurement speed, resolution and accuracy when in individual measurement test modes. The 12061 has built-in a high speed, low interference A/D converter with a maximum speed of 2000 rdgs/s, making it the best solution for high speed measurement.

Product

Battery Safety Testers

-

Chroma Systems Solutions, Inc.

Chroma Systems Solutions, Inc.

The flexibility of our battery test equipment provides customers a test environment specifically for their application requirements.

Product

AC / DC Electronic Loads – Benchtop Testing to Automated Test Systems

-

Chroma Systems Solutions, Inc.

Chroma Systems Solutions, Inc.

Chroma is the global leader in Electronic Load manufacturing. Chroma’s AC Electronic Loads are designed for testing uninterruptible power supplies(UPS), Off-Grid Inverters, AC sources, and other power devices such as switches, circuit breakers, fuses and connectors. Chroma’s DC Electronic Loads are used for power testing in all markets including automatic test systems, LED, power supply testing, battery testing, and fuel cell testing. Chroma loads can do it all including full current down to 0.4VDC, CZ mode, user defined waveforms, timing measurements, and 3 current ranges per load. Chroma’s electronic loads come standard with either USB or RS232 ports for control and can be configured for GPIB (IEEE-488) control as well.

Product

Safety

-

Chroma Systems Solutions, Inc.

Chroma Systems Solutions, Inc.

The purpose of safety testing medical electronic equipment is to be sure that a device is safe from electrical hazards to the patient and caregivers. There are a number of UL, European and Canadian standards that serve as the ruling body on how medical products will be tested, one in particular, IEC60601 (the International Electrical Safety Standard for medical electronic equipment) is experiencing “global harmonization,” meaning it has been accepted and implemented around the world. The IEC60601 standard is mainly intended for product development where safety considerations must be taken into account early in the design phase of a product, however much of it is applied to production line testing since it is the only way for a manufacturer to be sure they are shipping safe product.