Pulse Instruments
Pulse Instruments is a leading manufacturer of systems and equipment for characterization and production test of CMOS, CCD and IR image sensors, including science-grade devices. Science teams have used Pulse Instruments systems to extract maximum performance from several HST CCDs, including the chip in the most recently installed Advanced Camera System that is providing 10x the performance of its predecessor.
- (310) 515-5330
- sales@pulseinstruments.com
- 22301 S. Western Ave.
#107,
Torrance, CA 90501
United States of America
-
Product
Pattern Generator
PI-2005
-
As a test engineer or digital designer you must have state-of-the-art tools to test, characterize and verify your complex semiconductor devices and digital circuit boards. The PI-2005 Pattern Generator will generate a wide range of simple or complex digital patterns for any test application that requires a serial or parallel digital data stream. To meet the requirements of complex devices and digital circuits, the pattern generator can be configured from 16 to 64 output channels.
-
Product
Four Channel Low-Noise DC Bias Card
PI-41702
-
The PI-41702 is a four channel bipolar DC Bias supply that can provide an output current up to 100 mA per channel. The output voltage ranges from –8 V to +8 V, and this card has special filter circuitry to reduce the output noise for those applications that require a low noise bias output. Additionally there is a ‘D’ type connector that allows the introduction of laboratory type supplies to reduce the noise further. To change from using the internal power supplies to external power supplies requires repositioning jumpers. The PI-41702 also has voltage and current sense for remote measurement of the voltage and current levels.
-
Product
65 MHz Single Channel Driver Card
40490
-
One channel, 65 MHz driver with an output voltage capability of ±20V. There are two inputs--a standard input with up 65 MHz capability and an optically isolated input with 20 MHz capability. Either input can be selected.
-
Product
Instrument Mainframe
PI-11006
-
The PI-11006 Instrument Chassis was designed to accommodate the power and noise requirements of some of Pulse Instruments analog instrument cards. These instrument cards, such as the PI-41401, PI-41702 and others supply signal outputs that require more current from the -12 V supply than available in a standard chassis. Therefore this chassis has a larger -12 V power supply that provides 2.5 Amps.
-
Product
GPIB Interface Card
PI-31000
-
The Pulse Instruments PI-31000 IEEE Interface Card is a standard GPIB Interface card offered by National Instruments. This interface card is used in applications where the PI-2005 Pattern Generator or other instruments are controlled from a remote system CPU, or it can be used as the system controller when the CompactPCI CPU is the system computer.
-
Product
Low-Noise DC Bias
-
Imaging devices, such as CCDs, IR FPAs, and CMOS image sensors, require DC bias with very low electrical noise to prevent contamination of the image. Image quality can also be enhanced by carefully tuning each bias voltage to extract the maximum signal/noise ratio out of an array. Pulse Instruments has decades of experience providing DC bias supplies with the flexibility required tocharacterize and test a variety of devices while maintaining the noise immunity required for satellite and astronomy applications.
-
Product
Characterization System
System 7700
-
Whether your application is characterizing a massive mosaic of CCDs for the next great observatory, designing a faster FLIR for a weapons-guidance system, or production-testing a CMOS image sensor for a digital camera, Pulse Instruments can supply you with a fully-integrated test system that allows you to focus on your your device, not on your test system.
-
Product
Dual Channel Driver Card
42460
-
Two channels of 32 MHz clock drivers with up to 20 volt amplitude. The output voltage range is ±20 V, with independent high and low voltage settings. The inputs to the Card can be optically isolated. The card also contains voltage and current sense capability, which allows muxing of the current or voltage output measurements from all the Driver Channels in the system to a single DVM. The card allows independent programming of the rise and fall time of each channel one nanosecond increments.
-
Product
Instrument Mainframe
PI-11008
-
The PI-11008 Instrument Chassis was designed to accommodate the power and noise requirements of some of Pulse Instruments analog instrument cards. These instrument cards, such as the PI-41401, PI-41702 and others supply signal outputs that require more current from the -12 V supply than available in a standard chassis. Therefore this chassis has a larger -12 V power supply that provides 2.5 Amps.
-
Product
Dual Channel Clock Driver Card
PI-41400
-
The PI-41400 is a dual channel Clock Driver card capable of operating up to 190 MHz into a 50-ohm load and up to 80 MHz at an amplitude of 8 volts into a 1-megohm load. Into a high impedance load the output voltage range is from a –3 volts to 8 volts with the output pulse amplitude ranging from 0.5 V to 9 V. When driving a 50 load the voltage range is –1.5 volts to 4.5 volts with the output pulse amplitude ranging from 0.25 V to 4.5 V. The rise and fall times of the output pulse are variable from 1.2 ns to 9 ns into a 50-ohm load and <5 ns to 9 ns into a HiZ load. The output pulse amplitude and the load being driven determine the range of variability. The driver output can be set for tri-state operation and the output polarity can be set for ‘Normal’ or ‘Inverted’ operation through software.
