-
product
Spring Back Tester
HTJ-16
Shanghai Dean Electrical Co., Ltd
Executive standard: GB/T4074.3-2008/IEC60851-3; Inspection standard: JB/T4279.4-2008Used to measure the spring back characteristic of enameled round wires with nominal conductor diameter of between 0.080mm and 1.600mm;Number of winding turns: 5 turns and a halfStop accurately at zero position of the scale after automatic windingAs soon as the value of spring back angle stop counting, the dial will stop to rotate immediately, so that the value displayed on LED and read on the dial are the same.Sensor is unnecessary to be adjusted for samples of different specificationsCoils loosen slowly during spring back, no action of spring back or jump suddenly.Application of SCM control allows for fast operation and strong anti-interference capacity;
-
product
Automotive Back Probe Pins
142-5
Flexible 1.5 inch silicon pins provide easy back probing connections for DMM and Scope measurements
-
product
Back Plane Tester
This machine is used to test back planes used in telecommunications central stations. An operator loads a completed point to point wired back plane onto a retractable shelf on the front of the tester. Table continues and the disk falls through a hole into the bin. The shelf is pushed back into the machine where it is held in place by pneumatic operated clamps. Then a series of pneumatic cylinders sequentially insert a test card into each location in the back plane. A remote instrument performs a complete point to point continuity, short and hi pot test on all connections in the back plane.
-
product
Back Pressure Tester
MDBPT2
Quickly test for back pressure and identify clogged or obstructed catalytic converters. Three stage adapter (18mm-12mm) for accessing O2 sensor ports or (standard 1/4-20) self tap access anywhere. Adapter flange for common Toyota style O2 sensors.
-
product
Mini Back Probes/Wire Piercers
618
*Great for backprobing weather pack style connectors used with numerous automotive sensors *Also very handy for piercing and tapping readings on smaller gauge wires - using the included probe adapters *Works with most Test Lead Kits in the field - with standard 4mm banana plug test lead *Set includes four probes - red, black, green, yellow Test probes 21 mm length
-
product
8 Connector-Hole Back Extension
9401-BE
Semi-enclosed version of the cabling "doghouse" for the Hawk/PC chassis with rear panel punched to accommodate 8 50/37 pin d-sub connectors. Space is provided to mount the standard DG-style 100 pin edge connector paddles.
-
product
Back Pressure Test Kit
389
Thexton Manufacturing Company, Inc.
Aids in diagnosing clogged or restricted exhaust systems.
-
product
Rapidox 6100 Pump Back Gas Analyser
The Rapidox SF6 6100 Pump Back is a fully-automatic zero-emissions SF6 gas analyser, designed for controlling and monitoring the quality and purity of gas used in high voltage switchgear, circuit breakers and transformers.
-
product
PXI/cPCI Programmable Power Supply - 16-bit Read Back Voltage and Current at Output
52912
Chroma 52912 programmable DC power supplies are designed specifically for test applications that demand precision output voltage/current and tightly coupled measurement capabilities.
-
product
Server Power And Back Up Unit Test Solutions
Built on the proven Chroma 8000 ATS platform, these customizable solutions are specifically designed for automated testing of server PSUs, power shelves, rack power systems, bidirectional DC/DC converters for BBUs, and low-voltage high-current DC/DC converters for motherboards.
-
product
Back Pressure Tester
TU29P
Enables Technician to test exhaust back pressure thru oxygen sensor. Oxygen Sensor adapter includes M12 & M18 thread.Special Gauge has two multi-colored bands - idle and 2500RPM, with pressures shown in PSA and bar.
-
product
Pump Back Gas Analyser
Rapidox SF6 6100
The Rapidox SF6 6100 Pump Back is the latest in fully-automatic gas analysers, designed for controlling and monitoring the quality of SF6 in medium & high voltage gas insulated electrical equipment. Exceptional accuracy and stability are provided when measuring the purity of SF6 gas, through specially selected sensors.
-
product
16 Hole Back Extension
9561-BE
Enclosed version of the cabling "doghouse" for the Hawk/PC chassis with rear panel punched to accommodate 16 50/37 pin d-sub connectors. Hinged for access to the rear of the DG-style backplane.
-
product
24" Front to Back Stiffeners
FB-24
Additional aluminum extruded front-to-back stiffeners are available for Vertical Cabinets. Includes installation hardware
-
product
Back and Forth Scratching Tester
WGQ-60
Shanghai Dean Electrical Co., Ltd
Executive standard: NEMA、JIS; Inspection standard: JB/T4279.15-2008Used to detect the scraping resistance of coating and cable insulation layer of flat wires of 0.800～5.600mm (narrow side) and the silk and enamel covered round wires with nominal conductor diameter of 0.100～5.000mm;Application of SCM control allows for fast operation and strong anti-interference capacity;Sample support table allows for parallel rise and fall, maintaining close contact between the entire plane with sample;Scratching needle is vertical to the paint scraping direction and parallel with sample supporting table;When film is scratched and the action current is ≥5mA, painting scraper would automatically stop scraping;LED would automatically display the number of scraping.
-
product
THREE WAY BACK PRESSURE KIT
TU24APB
*Allows quicker and more accurate testing of exhaust blockages in catalytic converters, mufflers, etc*2-1/2" gauge features two multi-colored bands - idle and 2,500 RPM - with pressures shown in PSI and bar*Includes 6' of hose, enough length to test from driver's seat
-
product
30" Front to Back Stiffeners
FB-30
Additional aluminum extruded front-to-back stiffeners are available for Vertical Cabinets. Includes installation hardware
-
product
Peel Back Force Tester
PBFT
Precisely measure the peel back force of carrier tape to verify your packaging systems are within specification. Results can be printed and stored with the outgoing product.
-
product
Wafer Back Side Cooling System
GR-300 Series
The GR-300 Series can control gases used to cool the back side of wafers that are fixed in position by an electrostatic chuck system.The stability and accuracy of the GR-300 makes it ideal for controlling the flow of Helium and Argon in wafer cooling systems.
-
product
Exhaust Back Pressure Tester
33600
Use to test for clogged or obstructed catalytic converters and mufflers. Fast and easy to use - threads into Oxygen Sensor Port. Includes 12mm and 18mm adapters to fit most domestic and imported vehicles. Gage measures 2 1/2" diameter and has dual scale: 15 PSI and 1.00 Kg/Cm2. Hose is 41" long.
-
product
1310/1550 nm Dual Laser Source Back Reflectiom/Power Meter
GM8019 + GM83001E
The UC INSTRUMENTS GM8019 + GM83001E 1310/1550 nm dual laser source back reflection meter and power meter is a compact, direct display instrument for the convinent measurement of backreflection, insertion loss and power connector, fiber optic components, and system. With a single output port, the meter is very easy to use and ideal for fiber cable jumper manufacturers.
-
product
Surge Suppressor to Suppress SCR Spikes from Customer Equipment Going Back to Utility Power, P/N 5965C
This Suppressor Board is ideal for SCR Controlled Power Supplies when SCR control is on the primary side.The Suppressor Board will prevent SCR spikes to go back into the 480 VAC utility power lines.
-
product
36" Front to Back Stiffeners
FB-36
Additional aluminum extruded front-to-back stiffeners are available for Vertical Cabinets. Includes installation hardware
-
product
High Quality Fiber Cleaver Auto-Blade-Back
SH-27
Shenzhen Sharingtek Communication Co., LTD
SH-27 series fiber optic cleaver is the new type of fiber cutter with high precision, greatly improving the working efficiency and efficiency.
