Transmitters

The Crocodile is an ANSI-95 CDMA transmitter that is ideal for simulating a CDMA Base Station with its Pilot I and Q modulated output and assignable PN Offsets. The transmitter is housed in a high impact, water resistant case, operates from AC or battery power and is ideal for field use. Available in either PCS or Cellular, the Crocodile is ab ...more

Enable a single technician to perform return band alignment with this easy to use return band alignment system for CATV. This system consists of a headend signal level receiver/telemetry transmitter (the HECTER 6103) and a small, field portable, dual-carrier signal generator/telemetry receiver unit (HECTER'S PUP 6106). ...more

The NPRT 2200 performs Noise Power Ratio measurements to determine the dynamic range of optical transmitters, amplifiers and other active devices used in HFC networks. It has an internal broadband noise source, selectable filters and a measuring receiver. ...more

The Noyes OLS7-FTTH and OLS7-3 laser sources from AFL Telecommunications are cost-effective, rugged, handheld instruments designed for performing insertion loss measurements on single-mode fiber optic links when used with an optical power meter. When paired with an optical fiber identifier, both models may be used for fiber identification. The ...more

The Fluke 787 was the first tool to combine a DMM and a loop calibrator to give process technicians double the power in one tool. Now its even better, the range is extended with the new Fluke 789 the ultimate loop calibration multimeter. The Fluke 789 has a 24-Volt loop supply reducing the need for taking a separate power supply when doing of ...more

The Raven is a portable, PN scanner used to measure and record (Ec/Io) IS-95 coverage of CDMA base stations. Raven measures active CDMA networks or it may be used in conjunction with CDMA transmitters such as the Crocodile? or Gecko? which are placed throughout an area of interest. The transmitters may be set to different base station PN offse ...more

Each Gator Transmitter is housed in a high impact ABS water-resistant case. It has a built-in agile frequency synthesizer, dynamically controlled power amplifier and a built-in modem and DTMF (touch-tone) decoding allowing remote control of all transmitter parameters via a phone line or cellular telephone. Remote adjustments include the power ...more

The Duet Channel Sounder, a two part transmitter and receiver system providing comprehensive analysis including BER, Multipath, Eb/No and RSSI. The Duet is a sequential correlating channel sounder which is an improved version of the "sliding correlator sounder". The Duet Channel Sounder provides insight into propagation analysis in t ...more

Dragon is a lightweight, (under 15 lbs!) dual-transmitter system. The Dragon system is composed of 2 independent, dual 5-watt transmitter modules giving the user freedom to transmit on any 2 frequency bands from anywhere without swapping out or purchasing expensive and bulky additonal transmitters. Each Dragon is housed in a high impact ABS wa ...more

The Lizard is a portable, battery-powered 1 watt CW (Continuous Wave) or modulated (available on certain models) stimulus transmitter used for indoor coverage testing. The Lizard is ideal for WLAN set-up and evaluating network performance. In a typical application, one or more Lizards are placed throughout an area of interest and set on differ ...more

This MicroLog external sensor can sample any device or transmitter, producing a linear current between 0-20 mAmp. The 0-20 mAmp can be converted to the correct measured units by using Microlab¹s calibration option. ...more

A general sensor that will measure any device or transmitter that produces a linear analog 0-10V output. The voltage can easily be converted to the correct measured units with the help of the Microlab program. ...more

The ML2495A and ML2496A Peak Power Meters have been designed for high resolution measurements on radar and the latest 3G and 4G wireless systems, including next-generation systems based on complex new modulation technologies such as OFDM. They have the highest bandwidth and highest resolution in rising edge pulse measurements. A combination of ...more

Used with GET-1200 transmitter to locate circuit breakers or fuses, controlling light fixtures, switches or any bare wires. ...more

42 V Ready: for use in the new generation of vehicles with mixed or single 42 Volt systems. Operates on DC voltages from 6 to 42 volts. Internally protected against power surges and overloads. 8" flexible probe allows reaching wires in congested places. Transmitter and Receiver LEDs show open or short circuit conditions. ...more

The COM3010 is a full featured communications service monitor engineered and designed to provide highly accurate measurement and monitoring of communications equipment from 100kHz to 1.0GHz with 0.1ppm accuracy. Full duplex design enables independent and separate measurement and testing of transmitter and receiver circuits simultaneously making it ...more

Tripp Lite's Multi-Functional Network Cable Tester allows you to test wiring continuity for Cat5, Cat6, Phone and Coax cable assemblies. Identifies mis-wires, short circuits and open circuits. Features two piece transmitter and receiver, two BNC-F coax converters and coax terminator. ...more

The Mini Bug Detector offers protection against wireless microphones and transmitters. This device is perfect for securing homes, offices and hotel rooms. It has a LED signal strength display and audio tone that help pinpoint the precise location of bugs. The Mini Bug Detector features wide range circuitry that enables it to detect concealed transm ...more

Source and measure 8 thermocouple type devices J, K, T, E, C, R, S, and N. One model for multiple thermocouple types with precision output displayed as mV or °C/°F. Microprocessor assures maximum accuracy to 0.15% of reading over wide ranges. High Accuracy Calibration function simulates precision thermocouple outputs for use in calibrating the ...more

Peace of mind is now within your reach. The Mini Bug Detector offers state of the art protection against wireless microphones and transmitters. Perfect for securing homes, offices and hotel rooms, the unit not only detects such devices, its LED display and audio tone actually pinpoint the precise location of bugs. The audio alarm can be turned ...more

Micro-Processor Controlled - Reduces False Readings. Fully Automatic - No Adjustments Necessary! 120/220 VAC Transmitter (250 VAC Max). Audible & Visual Indication  ...more

The DewPro MMY 30 is a loop-powered dew point transmitter for analyzing moisture content in dessicant air dryers, pipeline natural gas and industrial gases. The 4-20 mA output measures dew point temperature or ppm in gases at line pressure or atmospheric pressure.  ...more

The Q9000P is a 4-digit process receiver with extensive zero and span adjustment capability for readout in engineering units. The more popular process signals are 4-20 mA, 10-50 mA, 1-5 V and 0-10 V. The Q9000P can also be scaled for other signal levels. Full-scale input ranges are selectable from ±1 to ±50 mA (current signal) or ±0.5 to ±20 V (vol ...more

Two-wire Operation Power is obtained directly from the 4-20 mA loop, with no need for separate power input. This simplifies field wiring and eliminates the possibility of noise pickup from power lines. ...more

Infinity series universal panel meter. The INFINITY® The INFU universal meter is ideal for those who want a single meter to cover a variety of input needs. This meter can measure a broad spectrum of dc voltage and current ranges, nine thermocouple types, a variety of RTDs, a multitude of inputs from pressure transducers, load cells, strain gages as ...more