Showing results: 811 - 825 of 931 items found.
-
McLAREN Applied Technologies
The system consists of a powered pressure and temperature sensor with transmitter fitted to a wheel rim. This sends pressure and temperature data over an RF link to a compact receiver on the car. Sampling rates increase automatically when either a change in pressure is detected or when wheel inertia is detected. The system stops transmitting below a threshold pressure to preserve battery life. The receiver sends data to the car control via CAN.
-
LD-LOCC-A10 -
Labodam
Online Conductivity ControllerLD-LOCC-A10features 3 points conductivity calibration system, TDS measurement mode, and 4 to 20 mA output signal transmitter. The large and clear back light LCD displays Calibration and setup values, Temperature values, ATC (automatic temperature compensation) values, high and low limit of measurement. This controller measures Conductivity and TDS values in µS/ cm, and mS/ cm units.
-
Extech CB10 -
Extech Instruments Corporation
The CB10 is an AC Circuit Breaker Finder/Receptacle Tester that locates circuit breakers and tests receptacle wiring. The CB10 allows the user to quickly locate 110 Volt to 125-Volt AC circuit breakers and fuses with audible and visual circuit breaker indication. The product also features a variable sensitivity adjustment to pinpoint correct circuit breaker. This product is complete with a year warranty, the receiver and GFCI transmitter and a 9V battery for the receiver.
-
dB Control
dB Control designs and manufactures high-power microwave amplifiers, transmitters, high- and low-voltage power supplies and modulators for radar, electronic warfare (EW), electronic countermeasures (ECM) and data link applications. The modularity of our designs enables us to rapidly configure power products for custom applications. Our products can meet your specifications and platforms requirements for ground-based, shipborne and high-altitude military manned and unmanned aircraft.
-
DVB-C QAM -
TestTree
Combined with a Network Monitoring System or not, the EdgeProbe Advanced provides a powerful broadcast network alert & diagnosis tool allowing DTV network operators to monitor global trends and anticipate potential failures.EdgeProbe Advanced is able to monitor DVB-C and DVB-C2 signals at transmitter outputs, through its RF inputs (up to 4 in 1RU), as well as at modulator input and at Head-End/distribution links, through its ASI and IP inputs.
-
ISDB-T/Tb -
TestTree
Combined with a Network Monitoring System or not, the EdgeProbe Advanced provides a powerful broadcast network alert & diagnosis tool allowing DTV network operators to monitor global trends and anticipate potential failures.EdgeProbe Advanced is able to monitor ISDB-T and ISDB-Tb signals at transmitter outputs, through its RF inputs (up to 4 in 1RU), as well as at modulator input and at Head-End/distribution links, through its ASI and IP inputs.
-
DVB-T/T2 -
TestTree
Combined with a Network Monitoring System or not, the EdgeProbe Advanced provides a powerful broadcast network alert & diagnosis tool allowing DTV network operators to monitor global trends and anticipate potential failures.EdgeProbe Advanced is able to monitor DVB-T and DVB-T2 signals at transmitter outputs, through its RF inputs (up to 4 in 1RU), as well as at modulator input and at Head-End/distribution links, through its ASI and IP inputs.
-
ATSC 3.0/1.0 -
TestTree
Combined with a NMS or TestTree’s GlobalViewer, the EdgeProbe Advanced provides a powerful broadcast network alert & diagnosis tool allowing DTV network operators to monitor global trends and anticipate potential failures.EdgeProbe Advanced is able to monitor ATSC 3.0/1.0 signals at Transmitter output through its RF inputs (up to 4 in 1RU), as well as at Modulator input and Head-End/distribution links through IP (STLTP) inputs.
-
Leuze electronic GmbH + Co. KG
Contrast sensors detect and compare contrasts very precisely through the use of different light sources such as white light, laser-generated red light or RGB light. The detected contrasts marks are then reported to the process with minimal signal jitter. Through the automatic selection of the right transmitter colors, various color or gray value combinations can be reliably detected. Bar graph indicators offer additional ease in making adjustments during manual setup.
-
ULD-420 -
Amprobe Test Tools
When equipment begins to fail due to an air or gas leak or vibration, or electrical discharge, the leakage point emits an ultrasonic sound wave that is above the natural range of human hearing. The ULD-420 Ultrasonic Leak Detector converts this ultrasonic sound into a signal that can be used to pinpoint the exact location of the equipment failure. When working in unpressurized systems or the pressure is not sufficient enough to detect or verify a leak with the Receiver alone use the Transmitter.
-
EXFO Inc.
In lab and manufacturing environments, R&D engineers require scalable and optimized test solutions to enable them to properly characterize new advanced modulation scheme signals for next-generation, ultra-high-speed telecom networks. Through EXFO’s optical communication analyzers, R&D engineers and manufacturing operations involved in the development or production of transmitters or systems based on new high-speed technology will find the right tools for their advanced technology needs.
-
WTEM-2Q -
Langeo Co., Ltd.
WTEM-2Q time domain shallow TEM system is one of our latest researchers, with all functions and advantages of domestic and oversea shallow transient electromagnetic survey systems, integrated with WTEM-1J/GPS TEM system receiver and WTEM-1X low-power transmitter. It features high transmitting power, short turn-off time, high reliability, strong anti-interference performance (atmospherics, 50Hz or 60Hz industrial frequency interference), lightweight and low power consumption.
-
CZ1803 -
Aegis Pty. Ltd.
The CZ1803 is an inductive antenna accessory used to put a signal on any pipe or cable without having to make direct connection to that pipe or cable. You can simply plug the Inductive Coupler into the transmitter and your signal will be transmitted onto your target pipe or cable. When used with the TraceAll locator system, this inductive coupler is suitable for locating all services such as data, electrical, television, telecommunications cables and gas and water pipes.
-
DUC -
Kobold Instruments, Inc.
Two ultrasonic clamp-on transducers are externally mounted on a pipe and produce an acoustic path. The transducers send and receive acoustic signals and their transit times are measured by an electronic flow transmitter. The signal is accelerated by the flow in the forward direction. The return signal is decelerated by the flow in the opposite direction. The difference in time between the two, together with the path length L, can be used to determine the average flow velocity. This principle is known as the acoustic time-of-flight principle.
-
WIKA Alexander Wiegand SE & Co. KG
For high-precision online monitoring of the gas density, temperature, pressure and humidity of SF6 gas in internal and external systems of SF6 gas-insulated equipment, WIKA gas density sensors are exceptionally suited. The instruments are notable for their high-accuracy sensor technology which guarantees very good long-term stability and EMC characteristics. Optionally, there are hybrid solutions available which combine gas density transmitters with conventional gas density monitors with switch contacts.