Programmable Current Sources

The 1320 is a versatile unit, with a wide selection of user programmable capabilities, for testing or evaluation of inductor characteristics with a DC bias current applied. High DC Bias Current Offers flexibility with programmable DC current from 0 ? 20A, forward or reverse biasing. Up to 5 units can be connected in parallel to extend the curr ...more

The SS200 Fast Pulse (SS200FP) is a programmable current source optimized for OEM and laboratory applications where sensitive optoelectronic devices must be driven and monitored. The SS200FP provides DC or precise pulsed current up to 5A. Sophisticated SpikeSafe load transient protections continuously monitor the load during DC and pulsed modes a ...more

The Model 2790 SourceMeter Switch System is a high voltage, multichannel resistance measurement solution that speeds and simplifies electrical checks of airbag inflators and a variety of other automotive electrical test applications. It is the only commercial instrument that combines all the sourcing, measurement, and signal routing capabiliti ...more

The 236, 237, and 238 Source-Measure Units (SMU) are fully programmable instruments, capable of sourcing and measuring voltage or current simultaneously. These systems are really four instruments in one: voltage source, current source, voltage measure, and current measure. ...more

The SS200 High Current (SS200HC) current source is optimized for high current OEM and laboratory applications where multiple optoelectronic devices must be driven and monitored. The SS200HC provides DC or pulsed current up to 320A along with sophisticated load transient protection. SpikeSafe load transient protections detect and gracefully deal wit ...more

The earth bond tester P 3301 allows protective conductor tests and continuity tests which are in accordance with many standards (IEC, EN, UL, BS, VDE, etc.). To generate the high test current an electronic alternating current source is available, programmable between 10 AAC and 30 AAC. ...more

AC or DC high voltage dielectric breakdown testing of cables. Models available with AC & DC breakdown testing in the same unit. Programmable high current source from 1mA to 1A. Very accurate measurements of components in cable assemblies. 2-Wire & 4-Wire Resistance Measurement ...more

The OL 16A, used to operates the OL Series 550 Tungsten Ribbon Lamp Standards of Spectral Radiance with Sapphire Windows, is a microprocessor controlled, precision DC current source. This programmable DC current sources is specifically designed for operation of tungsten filament photometric, radiometric, and spectroradiometric standards. ...more

Programmable voltage -500 to +1500V, output current ±50mA in pulse mode, ±10mA in continous mode , 5 current ranges from ±10uA to ±50mA, rise time from 10V/ms to 1000V/ms, Voltage measurement range 1V to10000V, current measurement range from 100nA to 100mA, voltage monitor, current monitor ...more

The VT1518A 4-wire Resistance Measurement SCP provides four programmable current source channels (with input over-voltage protection) for excitation. Each current source can be programmed to provide either 30 mA or 433 mA. ...more

The VXI Technology VT1505A 8-channel Current Source SCP provides eight current sources programmable to one of two current levels. ...more

With the combined voltage and current source in a single compact chassis, the FX Series is the ideal choice for the simulation of high power levels. Either single or multi-phase, this versatile source can simulate power levels from just a few milliwatts to 54kW single phase or 162 kW three-phase and provides a universal system for both manual and p ...more

The OL 83A, used to operate all of the standards and sources listed under the OL 65A in addition to the OL Series 200 and OL FEL standards, is a microprocessor controlled, precision DC current source. This programmable DC current sources is specifically designed for operation of tungsten filament photometric, radiometric, and spectroradiometri ...more

Wide Test Current Range: User programmable output current, 3A to 45A AC in 0.01A steps, provides extensive coverage for testing to UL, CSA, VDE, IEC and other agency safety requirements. Programmable Source Voltage: Limit the voltage to the DUT using the programmable source voltage from 1.0V to 8.0V rms and meet the low voltage requirement of ...more

High Current Source and Measurement Unit. Programmable 16Bit current source of ±50V/±20A continuous output. Programmable output pulses up to ±50V/±100A for a maximum of 2ms ...more

These Power Managers are high voltage 20-, 25-, and 35-Watt fast programmable power supplies, which can stabilize a voltage or current against the effects of load, source, or temperature changes, yet respond with agility to programming signals requiring s ...more

Characteristics of SFB 1050. Voltage source with adjustable current limitation. Current source with adjustable Voltage limitation. Programmable capacitors Cf, Cs and feeding coils. External feeding mode. External adaptation of L, Rf and C  ...more

The OL 65A, used to operate the OL Series 220, 245, 300 and 752-10 standards in addition to the OL Series 740-20 High Intensity Source Attachment, is a microprocessor controlled, precision DC current source. This programmable DC current sources is specifically designed for operation of tungsten filament photometric, radiometric, and spectroradi ...more

64 bit Hot Swap 66 MHz, PCI/PCI-X extender card, 3.3V keyed top connector* 3.3V5V Signal Level Conversion Software programmable via parallel port to:  ...more

NGPU Power Supplies are constant voltage or constant-current sources, which can be programmed via IEC/ IEEE bus or operated manually. Three selectable current ranges and one floating test output which can be switched between voltage and current make the NGPU ideal for use in IEC/ IEEE-bus test systems. ...more

Programmable Triple Power Supply. Insensitive to RF voltages radiated by device under test or nearby antenna. Simultaneous readout of nominal and actual values of all channels. Coupled protection mode for DUTs which should not be supplied from an asymmetrical voltage source. Software calibration via IEC/IEEE bus without potentiometer adjustmen ...more

Advanced Conversion Products offers programmable DC power sources for a variety of industrial and laboratory applications including oil field wireline power and telemetry. Both standard and customized units are available to suit customers needs. Our DCP Series of DC sources feature very low noise. The wireline used to conduct DC power to the down- ...more

Power Supply Module - programmable voltage/current source which can supply a load current of ±200mA at voltages of ±100VDC. Analog circuitry consisting of two precision DACs, error amplifier, precision voltage clamp, voltage controlled current source (VCCS), power output stage, sense buffer amplifier, and precision feedback components. Voltage ...more

32 bit Hot Swap 66 MHz, PCI/PCI-X extender card, 3.3V keyed top connector* 5V<=> 3.3V Signal Level Conversion Software programmable via parallel port to:  ...more

The ContinuousWave (CW) Series of AC power sources provides clean single phase power at an impressive price/performance ratio. These compact switch mode sources come in two series, manual (CW-M) or programmable (CW-P) with standard IEEE-488.2 and RS 232 control. Both the manual and programmable models can be field configured for three phase op ...more