Instrument Amplifiers

Fixed Frequency CompactPCI electronic filter/amplifier cards from 1.0 Hz to 100 kHz. ...more

Fixed and programmable gain amplifier modules and instruments from -12 dB to +60 dB with full power bandwidth to 1.0 MHz. ...more

The PMC-AD8 module provides a high performance data acquisition subsystem. Octal 16 bit channels, 200 KSPS ADC?s. The Local DSP can be used to simply move data samples to the PMCbus or can provide processing functions such as limit checking, FFT's, digital filtering, etc. Software can be downloaded to the DSP via the PMC interface. Instrumenta ...more

The 6165 is a two-channel amplifier-filter module. Each channel has isolated input, 50 kHz bandwidth and two outputs that can be filtered or wideband. Bandwidth of 100 kHz is optional. The input is two-wire shielded and is isolated from the outputs, power and control interface. This gives the user complete freedom to ground the input without c ...more

The 6035 input module has eight channels of programmable transducer signal conditioning amplifiers and digitizer. Each channel has programmable voltage excitation, bridge completion and balance, programmable gain instrumentation amplifier, four-pole low pass filter and sample and hold amplifier. Channel outputs are multiplexed and digitized to ...more

The NPRT 2200 performs Noise Power Ratio measurements to determine the dynamic range of optical transmitters, amplifiers and other active devices used in HFC networks. It has an internal broadband noise source, selectable filters and a measuring receiver. ...more

VMEbus fixed frequency and programmable filter products from 1.0 Hz to 2.0 MHz and fixed and programmable amplifier products from -12 dB to +60 dB. ...more

Benchtop Instruments including programmable electronic filters from 0.1 Hz to 300 kHz and programmable gain amplifiers from -12 dB to +60 dB. ...more

Rackmount Instruments including programmable electronic filters from 0.1 Hz to 300 kHz and programmable gain amplifiers from -12 dB to +60 dB. ...more

The LDC-3926 16-Channel Laser Diode Controller offers 16 channels of high power laser diode current source and temperature control in a space saving rack mountable instrument. ILX Lightwave designed the LDC-3926 to meet the increasing pump laser control demands of high power optical amplifiers.  ...more

BASELINE 9400 TDR/ICE - the unique cable diagnostic system: - A state-of-the art cable fault locating instrument containing a high speed data recorder, capable of capturing and evaluating 40 million samples of electrical data per second, while also featuring amplifiers, attenuators and an adjustable pulse generator. ...more

Sixteen Differential Low-Level 16-Bit Analog Input Channels. Software-selected ranges: ±10mV, ±100mV, ±1.0V, ±10V. Expandable to 256 Channels with Companion Expansion Boards. 16-Bit Scanning ADC.  Instrumentation Amplifier per Input Channel ...more

Eight Differential Low-Level 16-Bit Analog Input Channels. Software-selected ranges: ±10mV, ±100mV, ±1.0V, ±10V.  Expandable to 128 Channels with Companion Expansion Boards. 16-Bit Scanning ADC. Instrumentation Amplifier per Input Channel ...more

The Maury MT868C/F is a packaged, broad band, microwave amplifier followed by a double sideband mixer which provides low noise amplification of signals in the 1.8 to 18.0 GHz frequency range and down-conversion of these signals to a fixed intermediate frequency.  ...more

The Rotek Model 8100 is a precision source of AC voltage, current and phase angle used in the calibration and test of a wide range of electrical metering instrumentation. It has been designed to be nothing less than the ultimate electrical power calibration standard in both accuracy and flexibility. This single instrument replaces the complicated c ...more

The CPCI-AD16 module provides a 3U high performance data acquisition subsystem. The Local DSP can be used to simply move data samples to the CPCI bus or can provide processing functions such as limit checking, FFT?s, digital filtering, etc. Application software can be downloaded to the DSP via the CPCI interface. Instrumentation amp ...more

The PGA-16 is a 16-channel instrumentation amplifier with differential input, single-ended output, programmable AC or DC input coupling and pre-filter gain.  ...more

analog multimeter is a cost-effective, handy multimeter without amplifier, and includes an integrated circuit breaker which protects the current measuring ranges. The instrument is also equipped with ample overload protection in the voltage ranges thanks to generously dimensioned, high performance PTC thermistors. ...more

Our CSP™ Family of products bring flexibility to all surveying applications. All measurement components (high voltage, amplifier, discriminator and signal processing) are located in the probe. Each CSP also stores all calibration parameters, all application related settings, and all data logging points (up to 1,000 date stamped points) in memory. E ...more

The AAF-3 is a 2- to 8-channel anti-alias low-pass filter and instrumentation amplifier ISA bus plug-in board for front-end signal conditioning in PC-based data acquisition systems. ...more

The Model FL644 Isolation Amplifier is available in several versions, offering either gain or attenuation of an input signal. In all versions, the input is isolated from the output by up to 1000VDC. The unit is mechanically and electrically compatible with Encore's other FlexiLine DIN-rail mounted instrumentation. ...more

The Model FL645 RTD Isolation Amplifier conditions a resistance input from an RTD temperature probe. RTD resistance varies with temperature, producing a DC output voltage from the FL645. The input is isolated from the output by up to 1000VDC. The unit is mechanically and electrically compatible with Encore's other FlexiLine DIN-rail mounted ins ...more

APLAB's Function / Sweep / Pulse Generator is a group of high performance general purpose instruments used mainly for testing the freq. response of various types of amplifiers as well as bandwidth measurement of different types of filters. It's wide freq. range, amplitude control, types of waveforms, sweep facility and easy to operate features ...more

The DA1855A is a stand-alone, high-performance 100 MHz differential amplifier. It is intended to act as a signal conditioning preamplifier for oscilloscopes, digitizers and spectrum analyzers, providing differential measurement capability to instruments having only a single-ended input. When used with a DA1855A, oscilloscopes can obtain Common ...more

Calmar Optcom's EDFA has extended its wavelengh into L-band for DWDM transmission systems. The L-Band EDFA (AMP-STL) amplifies optical signals within the wavelength range 1570~1603nm. It provides low noise figure and excellent gain. It is a self-contained, robust and reliable instrument that is easy to operate.  ...more