Device Bus

USB-to-GPIB Hub Controller controls GPIB instruments and provides 6 powered USB ports for controlling USB instruments or for adding devices to the USB bus. Includes ICS and National Instruments style 488.2 drivers, ICS's enhanced GPIBkybd Controller program, demo programs, test utilities, USB cable and Instruction Manual. ...more

Model 4860A GPIB Bus Isolated Expander provides 2000 volts of isolation between two GPIB buses and drives up to 14 additional bus devices. Automatically locates Bus talker to eliminate address switches. IEEE-488.2 compatible. ...more

A IEEE-488.2 GPIB to digital interface with 40 I/O lines that can be used to easily adapt devices with digital signals to the IEEE-488/GPIB/HP-IP bus. Signal monitor feature allows the 4803 to detect signal changes on 15 inputs. High-current drivers and input pullup resistors. Drives more devices, longer lines and inputs CMOS signals or switch ...more

An enhanced bidirectional IEEE-488.2/GPIB to serial interface that can be used to adapt devices with RS-232 and RS-485 (RS-422) serial interfaces to the GPIB Bus. A 256 Kbyte RAM buffers up to 252,000 characters and frees the computer for other tasks while the 4894B transparently transfers data to or from the serial device when in the G mode. ...more

onTAP provides comprehensive boundary-scan test development tools with powerful run time software including pin-level diagnostics. onTAP provides everything required for robust JTAG test solutions. Robust ATPG for high fault coverage and precise pin-level diagnostics. Interconnect, Bus Wire, Pull-up/Pull-down, TAP Infrastructure tests, Shorts ...more

4-CH, 14/16-Bit, Up to 2 MS/s Simultaneous-Sampling Multi-Function DAQ Cards ...more

Our CELLizer battery monitoring will get a new family member, the wireless battery scan module called CM-9010/ZB. These modules do not need any longer complicated bus wiring to establish communication. We use the new ZigBee wireless communication technology from Freescale. This makes life much more simpler, especially for installation topics. ...more

Same speed Windows/NT Kestrel Co-Processor for equivalent system throughput, or more. Occupies one PCI slot. A writable control store, FPGA implementation of the HP1000 architecture with 4 MBytes of tightly coupled, zero wait-state memory. ...more

C&D Technologies is committed to supporting the emerging Intermediate Bus Architecture (IBA) and its many derivative approaches. Consequently, we offer more non-isolated, point-of- load (POL) DC/DC's, in standard packages and pinouts, than any other company. Our POL output voltages range from 0.75 to 5V . . . at current levels from 0.5 ...more

Mercury Load Banks are completely self-contained, freestanding units which include all resistive load elements, load control devices, load element branch circuit fuse protection, main load bus and terminals, cooling system, control power supply, unit controller and malfunction detection system and NEMA type enclosure. ...more

Tabernus has utilized our team of engineers to create the next generation of testing software in NorthstarADT - the ultimate tool for high-end SCSI and fibre channel peripheral engineering and field applications. Fully multi-bus and multi-threaded, NorthstarADT provides unprecedented flexibility, control and ability to stress your systems to ...more

Double speed Windows/NT Osprey Co-Processor for two times the system throughput, or more. Occupies one PCI slot. A writable control store, FPGA implementation of the PDP-11 architecture with 4 MBytes of tightly coupled, zero wait-state memory. ...more

The LBW-Series Load Banks are completely self-contained, freestanding units which include all resistive load elements, load control devices, load element branch circuit fuse protection, main load bus and terminals, water cooled system, control power supply, unit controller and malfunction detection system. ...more

Hawk Co-Processor (Hawk-E) including I/O bus adapter with control logic for DG-compatible I/O devices, two slots required. Supports both Programmed and Data Channel I/O. ...more

Deployment of Basic Rate ISDN into customer premises demands that the wiring and outlets are installed quickly and without error. With up to 8 terminal devices on the S-Bus, wiring errors can be easy to make but subsequently difficult to trace. ...more

Triple+ speed Windows/NT Osprey Co-Processor for five times the system throughput, or more. Occupies one PCI slot. A writable control store, FPGA implementation of the PDP-11 architecture with 4 MBytes of tightly coupled, zero wait-state memory. ...more

The PCI2PMC ( PCI to PMC ) adapter / carrier converter card provides the ability to install a PMC card into a standard PCI slot. The PCI2PMC has a PMC card slot mounted to a universal 1/2 length PCI card. Suitable for 32 bit or 64 bit data with 33 or 66 MHz bus operation. The PMC user IO connector Pn4 is brought out to two connectors for acces ...more

The module FlexTiny is an interface-hardware between FlexRay protocol devices and bus cables at a minimum size. It includes the Physical Layer device for the specific bus system. Bus termination can be selected by closing or opening soldering jumpers. ...more

Quad+ speed Windows/NT Kestrel Co-Processor for four times the speed of the Kestrel /SX. Occupies one PCI slot. A writable control store, FPGA implementation of the HP1000 architecture with 4 MBytes of tightly coupled, zero wait-state memory. ...more

16-CH, 16-Bit, 250 kS/s Low-Cost Multi-Function DAQ Cards ...more

AriesAT is a COM software developer?s kit (SDK) that allows programmers to write their own custom SCSI, iSCSI and Fibre Channel (FCAL) testing tools with minimal effort. AriesAT contains an API (application programmer's interface) that exposes core I/O functionality so developers can focus on writing test algorithms and user interfaces instead ...more

VG-863 is a built-in system type video signal generator for use with a built-in PCI bus. This generator is a special purpose digital output unit equipped with 2ch LVDS output. This supports RGB for each 10bit(256 supports various device. VG-863 uses full capability for built-in signal source for measuring instruments or inspection equipment. ...more

Able to adopt both ISA and PCI CPU cards, the GT7950 integrates a 14-slot PC-bus passive backplane, a 250W power supply, a removable shock-resistant drive bay, and a rugged versatile front panel in a single enclosure. Different from other IPC 14-slot chassis which can only support ISA devices, the GT7950's onboard 14 slots can support 9 ISA, 4 ...more

Europa! 3110 is a single X.25 interface module for ISA bus. It supports both Data Terminal Equipment (DTE) and Data Circuit Terminal Equipment (DCE). The module provides protocol processing for protocol stacks, triggers and filters, and device drivers for communication with the host system ...more

Programmable Triple Power Supply. Insensitive to RF voltages radiated by device under test or nearby antenna. Simultaneous readout of nominal and actual values of all channels. Coupled protection mode for DUTs which should not be supplied from an asymmetrical voltage source. Software calibration via IEC/IEEE bus without potentiometer adjustmen ...more