Current Sensors

This MicroLog external sensor can sample any device or transmitter, producing a linear current between 0-20 mAmp. The 0-20 mAmp can be converted to the correct measured units by using Microlab¹s calibration option. ...more

For laboratory or embedded applications requiring accurate measurement of DC, pulsed DC, or AC current, the Vektrex VCS series Hall-effect current sensors provide high-bandwidth current sensing with an amplified 50-ohm voltage output that can be connected directly to an oscilloscope or data acquisition system. ...more

The FlexProbe Model 24-3002 is a low cost AC current measurement probe designed to plug into digital multimeters, oscilloscopes and power recorders. The Model 24-3002 is composed of a flexible sensor and an electronic module with 4mm safety banana plugs with 3/4" spacing. ...more

The AmpFlex is a flexible AC current probe composed of a flexible sensor and an electronic module. The flexible sensor permits measurements on conductors where standard clamp-on probes cannot be used. Measurement range is 5 to 3000A.  ...more

The FlexProbe Model 24-3001 is a low cost AC current measurement probe designed to plug into digital multimeters, oscilloscopes and power recorders. The Model 24-3001 is composed of a flexible sensor and an electronic module with a 14" double insulated cable.  ...more

Single and multi-channel loggers accept inputs from industry-standard sensors, transmitters and transducers. Units are available for 4-20mA, 1 volt, 5 volt and 10 volt ranges and offer feature precision measurements to 5.5 microamps and 250 microvolts. ...more

The XYI-III All Digital Cylinder Luxmeter and Half Cylinder Luxmeter is based on all digital integral photometric measurement technology. It has no analogue unit, thus it is very simple to overcome the zero drift which is impossible to be avoided in current Luxmeter. The digital V(l) sensor has large dynamic range so that there is no range-changing ...more

The XYG-II All Digital Photometer is based on all digital integral photometric measurement technology. It has no analogue unit, thus it is very simple to overcome the zero drift which is impossible to be avoided in current photo-meter. The digital V(l) sensor has large dynamic range so that there is no range-changing error in it, moreover, it posse ...more

Brushless Servo Solutions. Designed to work with any standard three phase brushless DC servo motor equipped with Hall effect sensors. Three-state current control for efficient drive performance ...more

The XYL-IV All Digital Luminance-meter is based on all digital integral photometric measurement technology. It has no analogue unit, thus it is very simple to overcome the zero drift which is impossible to be avoided in current luminance -meter. The digital V(l) sensor has large dynamic range so that there is no range-changing error in it, moreover ...more

±100V or 0 to 22mA DC input ranges or 2 input channels, ±100V or 0 to 22mA DC input ranges (AC current with optional sensor) ...more

The CPMXXE series instruments are high precision broadband Calorimetric Sensors operating in millimeter and sub-millimeter wave range on a principle of substitution of microwave power by direct current power, using an autocompensating transistor transducer. Calorimetric Sensor is supplied with Calorimetric Power Meter M1-25M (indicator block), ...more

The Radio Ampstik uses the same current sensor technology as the original Ampstik. Its key feature is the ability to display the current reading up to 50 feet away from the sensor. The user has the option to hold the display in their hands, mount it to their hotstick, or hang it on their bucket. The Radio Ampstik display can hold up to four Tr ...more

Sensor module for the direct measurement of current, voltage and temperature. The module is designed for direct operation in more advanced measuring systems such as current-measuring devices and battery management systems. ...more

Software configured, performs linearization, square root extraction, and optional limit alarm functions. ±100V or 0 to 22mA DC input ranges (AC current with optional sensor). ...more

FlexTop 2211 is a 4...20 mA loop-powered, confi gurable un versal transmitter with galvanic isolation between input and output. The input can be confi gured for RTD or T/C sensors, resistance, current or voltage signals. ...more

The AmpFlex is a flexible AC current probe composed of a flexible sensor and an electronic module. The flexible sensor permits measurements on conductors where standard clamp-on probes cannot be used. Measurement range is 5 to 10,000A. ...more

Model RH-20C outputs a 4-20 mA current loop for long virtually unlimited cable distances. TEGAM's RH series transmitters are an economical solution for the continuous monitoring of relative humidity. ...more

TEGAM's Humitran duct probes provide a reliable, accurate, and low cost method for monitoring relative humidity plus temperature. Solid state sensors supply excellent sensitivity, fast response and long term stability. Simple hook up and linearized output permit interfacing with most display or control devices. Model RDP-20C outputs a 4-20 mA ...more

The XYL-V All Digital Luminance-meter is based on all digital integral photometric measurement technology. It has no analogue unit, thus it is very simple to overcome the zero drift which is impossible to be avoided in current luminance-meter. The digital sensor has large dynamic range so that there is no range-changing error in it, moreover, it po ...more

Current & voltage measurements and voltage indication integrated in the same compact cast resin part. Conventional instrument transformers have been widely used in medium voltage networks for transforming high current and voltages to a level suitable for measuring and protection. The introduction of new digital technology for measuring and pro ...more

The NxtPhase Flexible Optical Current Sensor has a flexible fiber optic sensing loop that is easy to wrap around high voltage bushings, generator buses, or other conductors in ways not possible with conventional CTs. The sensing loop is an in-line, all-dielectric cable, which connects to standard NXCT electronics giving the user the same high ...more

These are the workhorses of the scientific product line. Originally available in a blue rectangular housing (known for a long time as the "LE-3D classic", now out of production), hundreds of these sensors are in daily duty all over the world. The current model (shown below) comes in a cylindrical stainless steel housing and is called ...more

The ESM-120 is a unique measuring head which enables you to determine the SAR. A new technology (protective rights registered in many countries) has made it possible for the first time, to determine the SAR in real-time. It consists of the actual measuring head with a HF sensor, the body with operating controls, LC display with illumination and an ...more

The NxtPhase Optical Current Sensor replaces conventional CTs & bring a new level of accuracy to current sensing over the range of 1A(rms) to 63kA(rms), from 138 kV to 500 kV. The sensor is based on the Honeywell Fiber Optic Gyro system which has a trusted reputation for accuracy & reliability in aeronautic & space industries for bot ...more