Cable Bus

The SR600 Series AC Current Probes are designed for use in industrial and utility environments. The unique ergonomic design allows them to easily clamp onto cables or small bus bars. Excellent transformation and low phase shift, plus a broad frequency response, permit accurate measurements of current for power and power quality measurements. M ...more

The MD300 Series probes are built for ruggedness, versatility and ease of use. They are designed with unique hook-shaped jaws that enable the user to "pry" into or "hook" onto cables (will accept 2 x 500MCM) or even smaller bus bars.  ...more

32 bit Hot Swap 66 MHz, PCI/PCI-X extender card, 3.3V keyed top connector* 5V<=> 3.3V Signal Level Conversion Software programmable via parallel port to:  ...more

15" x 15" Backplane Adapter. Not to be used in production environment. Used with any I/O bus adapter during installation of Hawk system. Presents Nova/Eclipse bus signals on dual 50-pin connectors. Two 10 ft. (3 m) ribbon cables included. ...more

The SCM is a microprocessor-based device that continuously monitors the insulation system for partial discharge activity as well as other parameters such as temperture and humidity. Application for the SCM includes switchgear, bus duct and cable systems. The basic standalone unit shown in the picture consists of three modules (from the left to ...more

Easy-to-use DBT100A handheld tester and DBT500 heavy duty tester are able to quickly troubleshoot or test a MIL-STD-1553B Data Bus Network. These test units can detect shorts, opens, crossovers and shorts-to-shield on the bus and stubs. The testers are designed so the user can perform these checks from the Line Replaceable Unit (LRU) ends of the st ...more

64 bit Hot Swap 66 MHz, PCI/PCI-X extender card, 3.3V keyed top connector* 3.3V5V Signal Level Conversion Software programmable via parallel port to:  ...more

The module FlexTiny is an interface-hardware between FlexRay protocol devices and bus cables at a minimum size. It includes the Physical Layer device for the specific bus system. Bus termination can be selected by closing or opening soldering jumpers. ...more

This cable can not work if your car uses a protocol/bussystem like VPW, PWM or CAN-bus. 2. Terminal K = Bus of communication 3. Terminal L = Ignition for waking up car computing system (ECU: Engine Control Unit) 4. Existed 3 different protocols with same OBD2 connector incl. ISO/KWP, VPW, PMW  ...more

The NxtPhase Flexible Optical Current Sensor has a flexible fiber optic sensing loop that is easy to wrap around high voltage bushings, generator buses, or other conductors in ways not possible with conventional CTs. The sensing loop is an in-line, all-dielectric cable, which connects to standard NXCT electronics giving the user the same high ...more

PMC-ExtendIO-II provides a 32/33 - 64/66 extension between a PMC and Host. Any combination of PMC PCI bus speed and data width can be accomodated. With 66 MHz implementations cable lengths may be restricted compared to 33 MHz usage. ...more

64 bit Hot Swap 66MHz, PCI/PCI-X extender card, 5V keyed top connector* 5V<=> 3.3V Signal Level Conversion Software programmable via parallel port to: ...more

IP-Debug-Bus is a specialized extender card which is optimized for testing IP Modules. The bus signals are all accessible via test points. The testpoints include multiple ground locations and .025 sq. posts for ease of connection to your logic analyzer or scope. The testpoints are labeled for easy identification. Power is controlled with an on ...more

64 bit Hot Swap 66MHz, PCI/PCI-X extender card, 3.3V keyed top connector* 5V<=> 3.3V Signal Level Conversion Software programmable via parallel port to:  ...more

The type 2231 is designed for measurement of contact resistance of such items as circuit breakers, switchgears or resistance measurement on fuses, cables splices, bus bars, welds, heating elements, battery terminal ballast, heater elements etc. ...more

Ribbon cables for connecting RTSI bus connectors on adjacent NI plug-in boards ...more

DC/AC 2000A. Cable f 55mm, Bus Bar 72mm(D) x 22mm(W). True RMS (2000). Average Sensing (2003). DCA One Touch Zero. Auto Range A, V, W. Continuity. Max/Min/Hold. Relative Measurement  ...more

The Model 2917 interfaces between a VMEbus system and as many as eight CAMAC crates using Model 3922 Parallel Bus Crate Controllers. Connection between the 2917 and the 3922s is made via a Model 5843-Txyz 40-conductor, twisted-pair ribbon cable. (Order this cable separately.) Balanced RS-485 signaling enhances performance and provides noise immunit ...more

PCMCIA interface cables to the CAN bus (9-pin male D-sub Combicon-style combined) ...more

COM485/8 is an eight-port asynchronous serial communications card for use in ISA-bus computers. It features eight independent ports, buffered type 16550 UART's, and automatic control to transparently enable/disable the transmission drivers as needed. Included with the card is a "spider" cable that provides eight shielded, 9-pin, mal ...more

Apcon's 4x2 SCSI Switch enables six independent SCSI buses to be selected and connected in any combination via internal electronic switching circuits. The 4x2 eliminates the need to swap and reconfigure SCSI cables and bus terminators each time a new system configuration is required.  ...more

The FS4400 PCI Express Serial Analysis Probe is a low-cost bus analysis probe capable of non-intrusively probing a PCI-Express bus at a serial data rate of 2.5 Gbps. The FS4400 connects to the system under test with one of several adapter cables. Protocol decode software is included to decode and display incoming data using an Agilent logic an ...more

Apcon's 2x1 SCSI Switch enables three independent SCSI buses to be selected and connected in any combination via internal electronic switching circuits. The 2x1 eliminates the need to swap and reconfigure SCSI cables and bus terminators each time a new system configuration is required.  ...more

The FS4400 PCI Express Serial Analysis Probe is a low-cost bus analysis probe capable of non-intrusively probing a PCI-Express bus at a serial data rate of 2.5 Gbps. The FS4400 connects to the system under test with one of several adapter cables. Protocol decode software is included to decode and display incoming data using an Agilent logic an ...more

The SMT510 series are Sundance Digital Bus cables which are used for high speed inter module communication. The cables and connectors are manufactured by ODU in Germany. ...more