-
product
Field Test
Field test equipment is an optimised solution for large system testing, which, thanks to its distributed architecture, enables the placement of several small-sized testing systems.
-
product
Heat Technology & Production Ovens
Weiss Technik’s complete portfolio of heating and drying ovens, tempering ovens, continuous ovens, production ovens and IR Infrared technology ovens provides advanced technology for your testing and production requirements. With advanced user and product safety features, our ovens meet many safety and industry requirements including EN 1539, and AMS 2750E or CQI-9. We have both pre-engineered and custom solutions.
-
product
ThermalAir Desktop Series Temperature Forcing System
ThermalAir TA-1000A Desktop System
The ThermalAir TA-1000 high capacity thermal air stream system is used for temperature testing, fast thermal cycling, and device temperature characterization of components, hybrids, modules, PCBs, and other electronic and non-electronic assemblies at precise temperature from -25°C to +200°C.
-
product
Light Meter
2330 LX
Standard Electric Works Co., Ltd
● Wide range for measurements up 40000 lux and 4000 fc.● 0.01 lux and 0.001 fc resolution for accurate low light level measurements.● Light sensor cover is included for preserving sensor life.● Auto off function.● Data hold function.● Low battery indication.● Over range indication.● Auto-ranged.● Manual-ranged.● Calibration mode is provided.● 9V battery system.● Selection key for lux and fc.● The spectral sensitivity close to CIE photopic curve.● Ideal tool for workplace, clean-room and computer room light testing.● Video, photographic, office, classroom, and architectural uses.
-
product
Mechanical Testing
A range of processes including:Tensile and Compression Load TestingA test piece or component is subjected to tension (or compression) until either a proof load is achieved or failure occurs.Testing can be carried out on both metallic and some non-metallic materials.
-
product
Minority Carrier Lifetime Tester
HS-CLT
HS-CLT Minority Carrier Lifetime Tester has strong functions. It can not only measure carrier lifetime of wafer but also silicon ingot, silicon filament,silicon phosphorus ingot,silicon boron ingot, seed crystal and other irregular shape silicon material.The minority carrier testing ranges from 1μs to 6000μs, the minimum resistivity is 0.1Ω.cm, (can be extensive to 0.01Ω.cm). Dynamic curve monitoring in the whole process.
-
product
Radar Test System
UTP 5065
Radar sensors are core elements to realize autonomous driving. The UTP 5065 radar test system from NOFFZ Technologies has a compact vertical design and contains everything needed to allow State-of-the-Art measurement and sensor calibration. The test bench setup and component selection are tuned to get best possible results for highly accurate and cost-efficient testing in production of automotive radar sensors.
-
product
Germination Testing Equipment
Popular Science Apparatus Workshop
An estimation of the viability of seeds within a population.
-
product
Solar PV Testing
We've been manufacturing solar PV testing solutions for nearly a decade and have become a trusted name within the industry. Whether you are a residential, commercial or utility scale PV installer, or testing 1000V and 1500V installations, we have a PV testing solution for you.
-
product
Temperature And Humidity Chambers
Dongguan Amade Instruments Technology Co., Ltd
Temperature and humidity chamber is also referred to as climatic chamber, programmable temperature humidity chamber, constant environmental test chamber, constant humidity chamber, temperature and humidity controlled cabinet etc. It Is capable of simulating the range of temperature & humidity fluctuating from an extremely low value of -70℃ & 20% R.H to an exceeding high value 150℃ & 98% R.H which products may be exposed to in the natural environment. Constant temperature&humidity...show more -
product
Connected Devices And Services Testing
Ensure the quality of experience for connected devices and services.
-
product
Cable Test Van
The desire for faster and more efficient cable fault location as well as cable testing and diagnostics demands the ergonomic installation of equipment into vehicles. To be able to satisfy the customer's particular requirements, each system is factory-fitted into a vehicle of their choice. The size of vehicle will dictate the equipment at the planning stage. Ergonomics, taking into account the customer's needs, is paramount.
-
product
RF Shielded Box
LTL Q20001
LTL Q20001 RF Test Enclosure is the streamline solution to manage your RF Testings. LTL Q20001 RF shielded test enclosure can comfortably house the intermediate and large devices on test such as Laptops, larger test Fixtures and other large RF devices.LTL RF Enclosures are available in aluminum and stainless steel models and come with a specialized EMI gasket which enables stable and effective RF shielding performance in all frequency bands.
-
product
PXI 8-slot BRIC Power Multiplexer, 8-Channel, 12-Pole (4 Sub-cards)
40-571A-302
The 40-571A-302 is a 8-channel, 12-pole 3 Amp Power Multiplexer and is part of our BRIC family. The 40-571A range is designed to simplify the connection of a common set of test equipment to one of a number of different devices for testing.
-
product
PXIe-7867, Kintex-7 160T FPGA, 18-Channel AO, 1 MS/s, PXI Multifunction Reconfigurable I/O Module
785570-01
Kintex-7 160T FPGA, 18-Channel AO, 1 MS/s, PXI Multifunction Reconfigurable I/O Module—The PXIe-7867 features a user-programmable FPGA for high-performance onboard processing and direct control over I/O signals for complete flexibility of timing and synchronization. With 18 analog output channels connected directly to the FPGA, you can quickly design for applications that require precise timing such as hardware-in-the-loop testing, custom protocol communication, sensor simulation, and high-speed...show more -
product
LXI High Voltage Matrix 2-pole 300x2
60-310-302
The 60-310 is a 2-pole Matrix Module available in 300x2, 200x2 and 100x2 formats. It is capable of cold switching 1000VDC and has a maximum carry current of 1A. It is designed for high voltage applications including circuit board isolation testing, relay testing, semiconductor breakdown monitoring and cable harness insulation testing.
-
product
PAT Testing Software
How PAT test results are recorded and managed can be an important factor in the implementation of effective workplace electrical safety testing programs.
-
product
Altitude Testing
Our environmental testing facilities simulate altitude testing from -400 ft. (-121 meters) to outer space at 100,000 ft. (30,480 meters) or up to 10-6 Torr (1.3e-7 kPa) with temperature applied as low as -300°F (180C). We can reach these heights within 5 minutes or less. We are capable to handle products measuring up to 4ft X 4ft X 8ft to many standards, including MIL-STD-810 and RTCA DO-160.
-
product
Stator Testing System for EV Motor
EVT531
Shanghai Dean Electrical Co., Ltd
To meet the standard test projects requirement of the international companiesTo control and analysis the programs will reduce the human careless and misjudgmentEasy to edit environment and easy to learnIt can test multiple sets of DUTs simultaneouslyWhen there are several DUTs are tested, it could identify the undesirable sets individuallyThe Impulse/Surge with waveform comparison is a non-destructive analysisPolarity testMaximum saved files will be up to 100 setsIt provides the password functionSpeeding test could save time and improve efficiencyChinese and English pages can be arbitrarily switched
-
product
GAOTek Handheld Gigabit Ethernet Tester
A0060001tek
GAOTek Handheld Gigabit Ethernet tester is designed for installation and maintenance of 10 M/100 M/1000 M Ethernet networks. It combines the functions of network testing, data packet capture, traffic generation, cable testing and BER testing into one unit. It also integrates full RFC-2544 and Y.1564 tests. Featuring an ergonomic design and 5.0 inch LCD color touch screen, this Ethernet tester helps the front-line field workers to analyze the network quality and locate faults rapidly. Test results can be shown graphically and numerically.
-
product
PC Controlled High Voltage Tester
Cablescan H23
The Cablescan H23 combines low-voltage solid-state technology with high-voltage relay technology ¾ solid-state devices for testing continuities and components at low voltage; relays for testing high-resistance isolation and high-current continuity.
-
product
TDK Test Services
TDK Test Services offers testing to domestic and international EMC test regulations, including IEC, ISO, CISPR, and SAE. Test services are offered in our 3m semi-anechoic chamber, 3m fully-anechoic chamber, 10-meter open area test site, and our shielded conducted test chamber.
-
product
Environmental Testing
Large Walk-in Environmental Chamber, and Walk-in Salt Fog Chamber, various sizes of vibration and shock equipment, and environmental chambers.
-
product
Tester for Electromagnetic Clutches and Control Valves
MS121
MS121 is a professional tester, a multifunctional device which successfully combines two functions: testing of electromagnetic clutches and control valves of vehicle air conditioners. Thanks to the color 4.3" TFT display and convenient menu, the device is user-friendly and possesses high-accuracy measurements. Testing can be performed either separately on the compressor or directly on the car. The tester has a metal case and is resistant to the effects of lubricants. The original topology of the tester board increases its reliability, the color marking of the diagnostic contacts minimizes the possibility of incorrect connection.
-
product
Development Switches
TTESwitch A664 Lab v2.0
The TTESwitch A664 Lab v2.0 supports laboratory testing and development efforts for non-real-time to hard real-time operations in distributed systems. The flight-capable TTESwitch Module A664 Pro is the core of TTESwitch A664 Lab v2.0. This enables a reduction in the development cost and time of a flightworthy switch.
-
product
Battery Tester
BAT-250
The Amprobe BAT-250 Battery Tester is designed for one-handed, comfortable and reliable battery measurements. The uniquely designed tester offers an ergonomic slider and a v-shaped side cradle to better hold batteries in place during testing and a contoured case shape that fits neatly in your hand. Testing your batteries has never been easier.
-
product
Coupling Decoupling Network for Conducted Common Mode Immunity Testing According to IEC 61000-4-6
CDN
The CDN M5 is intended to inject common mode disturbance signals to power supply of mains lines (unscreened) in the frequency range from 150KHz to 230MHz. A variety of calibration adapters and other accessories are available as an option. RF Standard connector: BNC type, AC socket 4mm safety bananas.
-
product
Laser Diode Characterization Testing
The Yelo Laser Diode Characterization system performs automated characterization of a laser device. The system will allow the operator to load a single packaged Laser device into a TEC controlled fixture mount. Each test station (LIV, Spectrum, Far Field/Beam Divergence) will then automatically align with the Laser Device in a sequential order and perform the automated tests required of each station.
-
product
Flex Test Fixtures
FTFs are test fixtures which are dedicated for testing flex-based components and assemblies such as displays, touch panels and more. A weak spot in a typical functional test system is the method to connect DUT flexible cable to a circuit board where the simple method of attaching the flex directly with an ZIF or LIF connector fails.
-
product
Compact 6-Position Dissolution Tester
Vision G2 Classic 6
The Vision G2 Classic 6 dissolution tester is the compact, rugged workhorse sibling to the Vision G2 Elite 8. Named in honor of the world’s first dissolution tester, a six-position test station introduced by Hanson Research in 1969, the G2 Classic 6 is precision engineered to ease the rigors of manual dissolution testing. The G2 Classic 6 meets and exceeds worldwide standards including compliance with USP, FDA, ASTM, EP, JP, CE, CSA, RoHS, and 21 CFR Part 11.
