Waveguides
guide the propagation of electromagnetic, light or sound waves.
See Also: Millimeter Waveguides, Optical Waveguides
-
product
Waveguide and Coaxial Rotary Joint Assembly
Waveguide and Coaxial Rotary Joints are used for the transmission of power and signal between the locked and rotating parts of a radar or satcom system.
-
-
product
3 Port Devices
Teledyne Lincoln Microwave supplies 3 port circulators and isolators that operate from UHF to V Band. They are available in a range of different packages; planar microstrip, coaxial and waveguide.
-
product
Mechanical Calibration Kit, 18 To 26.5 GHz, Waveguide, WR-42
K11644A
The Keysight K11644A calibration kit contains the precision mechanical standards required to calibrate the systematic errors of Keysight network analyzers. This calibration kit has a precision airline for performing the Thru-Reflect-Line (TRL) calibration, the most accurate error-correction technique for coaxial measurements. This kit also contains a commercial calibration certificate, flush short circuit, a precision shim, and fixed termination(s).
-
product
Components - Harmonic Mixers (WHMB)
WHMB Series
Farran Technology manufactures a comprehensive range of waveguide harmonic mixers for use with industry standard spectrum analysers and other custom applications. Models WHMB are fully calibrated broadband balanced diode units covering 26.5-110 GHz in standard waveguide bands. We also offer a low cost general purpose model WHMP covering 26.5-170 GHz.
-
product
Coaxial Waveguide Adapter, 1.85 mm (f), 40 to 60 GHz
U281A
The Keysight U281A adapter transforms waveguide transmission line into 50-ohm coaxial line. Power can transmitted in either direction, and each adapter covers the full frequency range of its waveguide band with SWR less than 1.3.
-
product
Waveguide Harmonic Mixers (Smart Mixers), 55/60 to 90 GHz
M1971E
Keysight M1971E 55/60 to 90 GHz waveguide harmonic mixers is an un-preselected mixer provides a complete solution for wideband millimeter-wave signal analysis of more than 2 GHz with X-Series signal analyzers. Smart features are embedded to help you to greatly simplify your overall test setup and improve the DANL and TOI of your test system. Go smart with harmonic mixing for your millimeter-wave applications.
-
-
product
V-Band Low Noise Amplifier 50 to 75 GHz, 35 dB Gain, 5 dB NF
SBL- 5037533550-1515-E1
50 to 75 GHz, 35 dB Gain, 5 dB Noise Figure V Band Low Noise Amplifier for IEEE 802.11.ad WiGig. Model SBL-5037533550-1515-E1 is a low noise amplifier with a typical small signal gain of 35 dB and a nominal noise figure of 5 dB across the frequency range of 50 to 75 GHz. The DC power requirement for the amplifier is +8 VDC/150 mA. The mechanical configuration offers an in-line structure with WR-15 waveguides and UG-385/U flanges.
-
product
Waveguide Receiver Protector
The continuous evolution of radar systems creates an ever more complex RF power environment in which sensitive receivers must operate and survive. Teledyne limiters deliver vital protection for a wide range of receivers, providing protection from L-Band through to Ka-Band (1 - 40GHz) and peak power levels up to 1MW with unparalleled low insertion loss levels.
-
product
60 GHz Development System
PEM009
The Pasternack / Vubiq 60 GHz development system provides rapid evaluation of Pasternack’s 60 GHz waveguide modules for quick prototyping for millimeter wave wireless system development. This high speed wireless 60 GHz developer kit is created from a partnership between Pasternack and Vubiq (pronounced “View-bik”), an industry expert in designing 60 GHz RF systems. Our 60 GHz wireless development systems make it easy to design new products and applications in the emerging unlicensed millimeter wave ISM V band.
-
product
Double Ridged Waveguide Horn
DRH203
Frequency range: 200 MHz - 3 GHz VSWR (max): < 1.6:1Impedance: 50 O (Ohm)Connector: N female Power (CW / Peak): 400 W / 750 W
-
product
Waveguide Rotary Joints
Waveguide Rotary Joints are used for the rotary transmission of power and signal between the stationary and rotating parts of a radar or satcom system.EVERAXIS has designed and produced single and multi channel Waveguide (WG) Rotary Joints since 1958. Every new design is simulated in FEM software as well as physically tested for optimal performance. Each high power Waveguide Rotary Joint is tested at maximum peak power before shipment.
-
product
Waveguides
CAES offers a full range of rectangular (WR-22 to WR430) and double-ridge (WRD-180 to WR430) waveguides covering frequency bands from a few hundred MHz to 100 GHz.
-
product
Multi-channel Optical Power Meter For Swept Test System
MPM-210HMPM-211, 212, 213, 215
Our MPM-210H is ideal for IL, WDL and PDL measurement of multi-port optical components including Dense Wavelength Division Multiplexing (DWDM), Arrayed Waveguide Gratings（AWG) , Wavelength Selective Switches (WSS) and more. When combined with our TSL-Series laser equipped with a power monitor output, the MPM-210H allows the user to complete real-time high precision IL measurements.
-
product
Double Ridged Waveguide Horn
QRH18
Frequency range: 1 GHz - 18 GHz VSWR (max): < 2.5:1Impedance: 50 O (Ohm)Connector: 2xSMA female Power (CW / Peak): 100W / 170 W
-
product
Coaxial Waveguide Adapter, 2.4 mm (m), 33 to 50 GHz
Q281B
The Keysight Q281B is a 2.4 mm male to WR-22 waveguide adapter that operates in the 33 to 50 GHz frequency range. These adapters transform waveguide transmission lines into 50 ohm coaxial lines. Power can transmitted in either direction, and each adapter covers the full frequency range of its waveguide band with SWR less than 1.3.
-
product
Full Band Noise Figure and Gain Test Extenders
STG-06-S1
Full band noise figure and gain test extenders are offered to extend noise and gain measuring capabilities up to higher millimeterwave frequency ranges. These extenders are designed to interface with noise and gain test systems that have an input IF of 10 MHz to 1.6 GHz, such as the industry standard Keysight 8970A/B, N8975A and Maury MT 2075B. The noise figure and gain test extenders include a high-performance, solid-state noise source (STZ series) and a full waveguide down converter (STC serie...show more -
product
Spot-Focusing Lens Antennas
The antenna employs a low loss lens to offer excellent aperture efficiency at 105.96 GHz. The lens antenna is equipped with a standard WR-10 waveguide and UG-387/U-M flange as its input port. It supports linear polarized waveforms.
-
product
Coaxial Waveguide Adapter, 2.4 mm (f), 33 to 50 GHz
Q281A
The Keysight Q281A is a 2.4 mm female to WR-22 waveguide adapter that operates in the 33 to 50 GHz frequency range. These adapters transform waveguide transmission lines into 50 ohm coaxial lines. Power can transmitted in either direction, and each adapter covers the full frequency range of its waveguide band with SWR less than 1.3.
-
product
Custom Waveguides
Custome waveguides for commercial, industrial, government and research & development industries. Consult with our engineering staff on your millimeter wave needs. View more Custom Waveguides
-
product
Variable Attenuator
VAXE
The VAXE Variable Attenuators are waveguide components for tunable signal leveling or reflection compensation in waveguide networks. The Attenuators consist of waveguide section with a resistive film evaporated on the mica surface. The Attenuators has 0 ÷30 dB minimum attenuation range. The VAXE Attenuators are available in four waveguide bands between 33 GHz and 170 GHz.
-
product
Multi-Wavelength Planar Lightwave Circuit Splitter (PLC Splitter)
PLC-1 × 口口口
Hangzhou Huatai Optic Tech. Co., Ltd.
Huatai Planar Optical Waveguide Optical Splitter (PLC Splitter) is an integration waveguide optical power distribution device that based on quartz substrate, featured with small size, wide working wavelength range, high reliability and excellent uniformity of optical split, etc. It is especially suitable for connecting local unit with terminal unit in passive optical network (EPON, BPON, GPON, etc.) to achieve optical signal splitting. The main design divide optical signal in optical communicati...show more -
product
Straight Waveguide Sections up to 110 GHz
Fairview Microwave’s straight waveguide sections consists of 61 models that are available in sizes ranging from WR-10 to WR-137. These waveguide straights deliver VSWR as low as 1.03:1 and are available in section lengths from 3 inches to 12 inches. They are made of either painted copper alloy or gold-plated, oxygen-free hard copper (OFHC) and feature UG, CPR and UBR-style flanges. These waveguide straight sections are ideally suited for use in industrial, defense, aerospace, test and instrumentation, medical and telecom industries.
-
product
Waveguide Power Splitters
*Low Insertion Loss*Coverage of full Waveguide Band*Available from 50 GHz up to 325 GHz
-
product
TDR Structural Health Monitoring
Material Sensing & Instrumentation
MSI Time-Domain-Reflectometry (TDR) Structural-Health Monitoring probes the structural health of a composite part by propagating a fast electrical pulse along a distributed linear sensor which has been fabricated directly in the laminate. The sensor is formed from the native graphite fibers already used in composite manufacture, and constitutes zero defect. Fibers are patterned into a microwave waveguide geometry, or transmission line, and interrogated by a rapid pulse as shown below. Structural...show more -
product
Waveguide Power Sensor
R8486D
Excellent SWR for reducing mismatch uncertainty50 MHz calibration port Accurate calibration and traceability to US National Institute of Standards and Technology (NIST) millimeter-wave sensor calibration Compatible with EPM (new N1913A/ 14A, E4418B/ 19B), EPM-P (E4416A/ 17A) and P-series (N1911A/ 12A) power meters, plus the E1416A VXI and discontinued 70100A and 43X power meter Accurate average power measurements over -70 to -20 dBm Frequency range 26.5 GHz to 40 GHz Diode power sensing element
-
product
Waveguide Cassette
Waveguide cassettes provide easy way for the network analyzer calibration and material properties as dielectric permittivity or (and) magnetic permeability measurements. By changing insertion sections, it is possible to calibrate "Short" and "Thru". Optional cassettes with quarter wave "short" inserters are available. Using this waveguide cassette, it is possible to do vector network analyzer calibration or additional scalar network analyzer calibration. Insertable sample holders supports two measurement methods: the rod in the centre of the waveguide and filled waveguide cross-section.
-
product
Millimeter Wave Control Devices
Ducommun millimeter wave products include various control devices for system integration. The CAE, CPS, CPD and CPM series control devices are discrete or MMIC based PIN diode attenuators and switches. The CAF, CAL, CAR and CPL series control devices are waveguide based mechanical tunable attenuators and phase shifters. These devices are offered to cover the frequency range from 18 GHz to 110 GHz.
-
product
Amplitude Detectors with Isolators
Full band waveguide detectors are GaAs beam lead Schottky diode-based detectors that are specially designed for millimeterwave network analyzer applications. With a proprietary circuitry design and careful diode selection, these zero-biased detectors exhibit high sensitivity and extremely flat output characteristics. The below standard offering covers the frequency range of 18 to 170 GHz and offers a 1 MHz video bandwidth and 1 MΩ video output impedance. The standard models also have the capacit...show more
