Waveguides
guide the propagation of electromagnetic, light or sound waves.
See Also: Millimeter Waveguides, Optical Waveguides
-
-
Product
Frequency Converters
-
Ducommun's frequency converter families include waveguide detectors (FAS), passive and active multipliers (FMP and FMA), up and down converters (FUB and FDB), harmonic mixers (FDH), subharmonically pumped up and down converters (FUS and FDS) and phase detectors and single sideband modulators (FPB and FSS). These devices are offered in 7 waveguide bands to cover entire 18 to 110 GHz frequency spectrum. These converters employ high performance GaAs Schottky beamlead diodes and DLT's proprietary circuit configuration to produce superior performance, such as low conversion loss and up to full waveguide instantaneous operation bandwidth.
-
Product
Waveguide Switches (Hi-Rel)
-
In 1993 Dow-Key expanded its involvement in Hi-Rel space programs with the acquisition of the Transco Space Qualified Products. In addition to the heritage for the Hi-Rel waveguide switches, many of the Transco design engineers stayed with Dow-Key and are still employed with us today.
-
Product
Coaxial Waveguide Adapter, 1.0 mm (m), 50 to 75 GHz
V281D
-
The Keysight V281D is a 1-mm male to V-band waveguide adapter with a frequency range of 50 GHz to 75 GHz. The Keysight V281D is used with the Keysight 8510XF systems.
-
Product
Precision Calibrated Noise Sources
-
ELVA-1's calibrated noise source ISSN-XX series delivers a uniform level of noise power spectral density within the whole waveguide frequency range. Sources are available in eight waveguide bands covering 26.4-170 GHz.
-
Product
Waveguide Power Amplifiers
-
RF solid state power amplifier (SSPA) PE15A4006 from Pasternack is part of the largest selection of in-stock radio frequency microwave and millimeter wave amplifiers available for same-day shipment. This Pasternack solid state RF power amplifier is a medium power amp design constructed in a connectorized package. Our SSPA is designed with SMA connectors and rated at 1 Watt.
-
Product
Waveguide Harmonic Mixer (smart mixer), 50 to 75 GHz
M1971V
-
Keysight M1971V 50 to 75 GHz waveguide harmonic mixer is an un-preselected mixer that provides a complete solution for wideband millimeter-wave signal analysis of more than 2 GHz with X-Series signal analyzers. Embedded smart features help you to greatly simplify your overall test setup and improve the DANL and TOI of your test system. Go smart with harmonic mixing for your millimeter-wave applications.
-
Product
Waveguide to Coaxial Adapters 1.7 GHz to 110 GHz
-
Fairview Microwave’s waveguide to coax adapters are made up of 77 models ranging in sizes from WR-10 to WR-430. These waveguide to coaxial adapters are offered in a broad selection of waveguide sizes, flanges, connectors and materials. Fairview’s waveguide to coax adapters support 10 different types of coax connectors and are available with UG (square/round cover), CMR, CPR, UDR and PDR-style flanges. Additionally, these waveguide to coax adapters deliver VSWR performance as low as 1.25:1 and are available with aluminum, gold-plated aluminum, gold-plated copper or painted copper alloy finishes.
-
Product
TDR Structural Health Monitoring
-
Material Sensing & Instrumentation
MSI Time-Domain-Reflectometry (TDR) Structural-Health Monitoring probes the structural health of a composite part by propagating a fast electrical pulse along a distributed linear sensor which has been fabricated directly in the laminate. The sensor is formed from the native graphite fibers already used in composite manufacture, and constitutes zero defect. Fibers are patterned into a microwave waveguide geometry, or transmission line, and interrogated by a rapid pulse as shown below. Structural faults along the line cause distortions in waveguide geometry, producing reflected pulses similar to radar. Cracking, delamination, disbonds, moisture penetration, marcelling, and strain are all detected by propagation delay, for sensor lengths up to several meters.
-
Product
Double Ridged Waveguide Horn
DRH30
-
Frequency range: 2.5GHz - 30 GHz VSWR (max): < 1.55:1Impedance: 50 O (Ohm)Connector: K female Power (CW / Peak): 25W / 50 W
-
Product
Scalar Network Analyzer
R24XE
-
The R24XE Scalar Network Analyzers provide both manual and automated VSWR, insertion and return losses measurements in five waveguide bands from 33 to 225 GHz. The system consists of the G44XE sweep generator, waveguide reflectometer, network analyzer and personal computer.
-
-
Product
Waveguide Antennas
-
Waveguide horn antenna is also known as a WR-15 horn antenna. This WR-15 waveguide horn antenna has a dB nominal gain and a ug-385/u flange. Our dB WR-15 horn antenna has a minimum frequency of 50 GHz and a maximum frequency of 75 GHz.
-
Product
Frequency Extension Heads for Vector Network Analyzers
FEV
-
These frequency extension modules connect to your existing test ports and leverage the inherent microwave network analyzer’s performance and features to display full port S-parameters: Two measurement architecture available: 1-path/2-port and fully reversing 2 port. Waveguide calibration kits are available as separate accessories.
-
Product
Double Ridged Waveguide Horn
QRH11
-
Frequency range:730 MHz - 11 GHz VSWR (max): < 2.4:1Impedance: 50 O (Ohm)Connector: 2xSMA female Power (CW / Peak): 100W / 170 W
-
-
Product
Millimeter-Wave Noise Source, Q-band, 33 To 50 GHz
Q347B
-
The Q347B waveguide noise source (33 to 50 GHz frequency range), allows you to make accurate noise figure measurements on millimeter-wave devices...
-
-
Product
Waveguide to Coaxial Adapter
DAWC-18-40G-2.92K
-
Waveguide to Coaxial Adapter, Frequency 18~40GHz, 50W, Double Ridged Waveguide WRD180C24, 2.92mm Female
-
Product
Coaxial Waveguide Adapter, 1.85 mm (m), 50 to 67 GHz
V281B
-
The Keysight V281B adapter transforms waveguide transmission line into 50-ohm coaxial line. Power can transmitted in either direction, and each adapter covers the full frequency range of its waveguide band with SWR less than 1.3.
-
Product
Waveguide Rotary Joints
-
Waveguide Rotary Joints are used for the rotary transmission of power and signal between the stationary and rotating parts of a radar or satcom system.EVERAXIS has designed and produced single and multi channel Waveguide (WG) Rotary Joints since 1958. Every new design is simulated in FEM software as well as physically tested for optimal performance. Each high power Waveguide Rotary Joint is tested at maximum peak power before shipment.
-
Product
RF Coaxial Probes & Probe Positioner
-
Fairview Microwave’s line of coaxial RF probes and RF PCB probe positioner are ideal for use with chip evaluations, signal integrity measurements, coplanar waveguide, substrate characterization, gigabit SERDES and test fixture applications. The RF coaxial probes provide return loss better than 10 dB and a maximum operating frequency of 20 GHz. The probes have a 3.5mm female interface, a pitch of 800 or 1500 micron and they can be cable-mounted. They feature gold-plated contacts and can be used by hand, with or without a probe positioner. Compliant coaxial GSG (or GS) pogo pins allow for a broad range of probing angles. The RF PCB probe positioner can hold coaxial probes, has articulated joints and delivers multi-axis positioner control. This positioner also boasts a magnetic mounting plate with on-off positioner switch.
-
Product
E Bend Waveguide
-
E-plane waveguide bends are sections of high-precision crafted waveguides and shaped to either 30º, 45º ,60º, or 90º angles for e-plane needs. It directs the radio frequency beam and “bends” the signal to go the direction you want. Think of it like Tokyo drifting around a corner in your car. Precision MMW will help you with the highest quality E bend waveguides. We are a millimeter wave spectrum manufacturer of various active and passive mmWave products and sub-system engineering.View more E Bend Waveguide
-
Product
In-Line Coaxial-to-Waveguide Adapter, 1.0 Mm (m) To WR-12, 60 To 90 GHz
E281DS
-
E281DS In-line 1.0 mm (m) - to- WR-12 waveguide adapter offers a simple way of measuring waveguide devices in E-band, 60 GHz to 90 GHz.
-
Product
Components - Low Noise Amplifiers (FLNA)
FLNA series
-
Farran's FLNA series low noise amplifiers are constructed with discrete or MMIC pHEMT devices that operate over the frequency range 18 to 110 GHz. These amplifiers are specifically designed for low noise applications.The amplifiers are offered in two categories: standard and custom-built. The custom-built amplifiers are offered in various RF interfaces, including standard waveguide or coaxial connectors, for convenient system integration.
-
Product
Microwave Testing
170
-
The PICOPROBE® MODEL 170, a high performance microwave probe which incorporates a WR-6 waveguide with our patented coaxial design techniques, has inherent low loss and low dispersion characteristics.
-
-
-
Product
Millimeter Wave Antennas
-
Ducommun millimeter wave products include ACH, ARH and ALC series circular, rectangular gain horn antennas and lens corrected horn antennas for system applications. Low side lobes, ridged configuration and low cost are the main features of these antennas. The standard gain value and half power beamwidth at mid-frequency point of each waveguide band are 23 dBi and 9 degrees, respectively. Other gain values are available as customer order. These antennas cover the frequency range of 18 to 110 GHz.
-
Product
Waveguide Power Dividers
-
2-way power divider that operates from 220 to 330 GHz. The power divider offers a typical insertion loss of 2.3 dB and typical isolation of 20 dB. All ports are well-balanced and in-phase for power dividing or combining applications across the band. The power divider is configured as a right-angle package with WR-03 waveguides and UG-387/U-M anti-cocking flanges at all ports.
