Showing results: 4846 - 4860 of 6649 items found.
-
MDPPTST -
Matco Tools
*USB, 12V and AC 110V socket testers provide the user with a simple way to test electrical sockets on a vehicle*Socket testers illuminate when when the respected voltage is detected, indicating the health of the socket*USB socket tester illuminates when 4.4V - 5.25V is detected
-
612 -
ACT Meters International Ltd
This digital battery tester is designed for testing 6V and 12V standby SLA, cyclic GEL and car FLOODED batteries. Simple in operation, the ACT 612 simulates a full 20 hour (C20) discharge test in seconds and displays the DC Voltage results and Ah capacity available.
-
AC, DC, AC and DC -
UDEYRAJ ELECTRICALS PRIVATE LIMITED
Panel mounted controls & indicators with easy to read legend.• Continuously variable output from zero to full voltage.• Low end ground test.• Multi range analogue kV meter and current meter.• Fast acting overload circuit breaker.• Zero start interlock.
-
VT14 -
Chauvin Arnoux Metrix
12 V to 690 V voltage test (7 diodes)Indication of polarity by " + " and " – " diodesImpedance: 400 kΩOperating frequency: DC and 50/60 Hzovervoltage protection up to 1,000 VIEC 61010 600 V CAT IIIPowered by 1 x 9 V 6LR61 battery (supplied)
-
Sivananda Electronics
Test Voltage : - 1V to 500V DC settableAccuracy : ± 1% of set Value ± 1digitLeakage Current : - Accuracy - ± 0.5% ± 1digitDigital Model – 19.99μA / 199.9 μA / 1.999mA / 19.99mAAnalog Model - 10μA /25μA/100 μA/1mA/2.5mA/10mASeparate Indication for Charge / Measure and Discharge modeAvailable in Digital Version Also
-
40-528B-001 -
Pickering Interfaces Ltd.
PThe 40-528B is a 128 crosspoint PXI matrix with single pole switching and a configuration of 32x4 using electromechanical relays with 2 A current handling. The module is designed for switching medium voltage and power signals, typical applications include signal routing in ATE and data acquisition systems.
-
Technology Products
Primary current injection kits are used to test and commission Circuit Breakers, Bus Bars, CTs, Relays, MCCs, PCCs etc. These are also used for high current injection and simultaneously measuring voltage drops and hot spots in bus-bar joints, Circuit Breaker Contacts etc.
-
290 HD -
Standard Electric Works Co., Ltd
● Telescopic, compact, lightweight.● High voltage detection.● Self test button feature.● Angle adjustment for 290 HD.● Easy to recognize indication.● High intensity red light emitting diode and intermittent audible sound for easy recognition in full sunlight and noisy environments.● Waterproof.
-
230 HD -
Standard Electric Works Co., Ltd
● Telescopic, compact, lightweight.● High voltage detection.● Self test button feature.● Angle adjustment for 290 HD● Easy to recognize indication● High intensity red light emitting diode and intermittent audible sound for easy recognition in full sunlight and noisy environments.● Waterproof.
-
2950 CL -
Standard Electric Works Co., Ltd
● Pocket size.● 4000 counts.● Full automatic measurement. Voltage measurement. Current measurement. Resistor measurement.● Data hold function.● Continuity check.● Diode measurement.● Select function.● Low battery indication.● Auto off function.● Flashlight (Auto off in 1 minute).
-
2940 CL -
Standard Electric Works Co., Ltd
● Pocket size.● 4000 counts.● Full automatic measurement. Voltage measurement. Current measurement. Resistor measurement.● Data hold function.● Continuity check.● Diode measurement.● Select function.● Low battery indication.● Auto off function.● Flashlight (Auto off in 1 minute).
-
IBEKO Power AB
DV Power manufactures ideal tools for maintenance, troubleshooting and performance tests on stationary batteries.Capacity testing is performed in order to detect which cells in the string should be replaced by measuring a cell voltage, temperature, inter-cell connection voltage, and specific gravity.IEEE standards for stationary battery applications also stipulate measuring these key parameters during periodic battery inspections.DV Power provides two types of instruments:BVS series – for automated monitoring of battery parametersBVR series – for manual monitoring of battery parametersIn contrast to BVS, BVR instruments can be used for the transfer of electrolyte specific gravity measurements from a density meter (DMA35) via Bluetooth. This provides a more extensive analysis of each cell in the tested battery string.
-
Fideris
* Fully programmable, self-contained, air-cooled solid state load.* Patented design is optimized to provide ultra-low impedance operation for fuel cell testing.* Load is compatible with AC impedance or frequency response analyzers.* Interchangeable shunts for precise operation over a wide dynamic range.* Ten built-in cell voltage monitoring inputs optional. Additional voltage monitoring inputs available.* Ethernet Interface for simple configuration and expansion!* Combine with additional Fideris™ Innovator Series™ modules to create a fully-integrated,fully-automated, customized test system.* System-wide control of all Fideris™ Test System Components using FCPower™ Software,LabviewTM, or other programming language.* Integrated hardwired Run/Standby signal.
-
ADGM1304 -
Analog Devices Inc.
The ADGM1304 is a wideband, single-pole, four-throw (SP4T) switch, fabricated using Analog Devices, Inc., microelectro-mechanical system (MEMS) switch technology. This technology enables a small, wide bandwidth, highly linear, low insertion loss switch that is operational down to 0 Hz/dc, making it an ideal switching solution for a wide range of RF applications. An integrated control chip generates the high voltage necessary to electrostatically actuate the switch via a complementary metal-oxide semiconductor (CMOS)-/low voltage transistor-transistor logic (LVTTL)-compatible parallel interface. All four switches are independently controllable. The ADGM1304 is packaged in a 24-lead, 5 mm × 4 mm × 0.95 mm lead frame chip-scale package (LFCSP).
-
ESI Technology Ltd
Single channel system, offering wireless transfer of a single analogue signal, either 4-20mA or DC voltage. Mixed signal radio telemetry solution. Analogue I/O: 2x 2-40mA or DC Voltage. Digital I/O: 2x volt free or optional pulse counting required. Multi-channel radio telemetry system, 4 Analogue and 8 digital inputs. Significant signal connectivity and data transfer in a standard package.12 I/O channels allow greater signal monitoring capability SENSOR LINK Compact wireless telemetry link for any strain gauge sensor or RTD. Transmissions distance 1 to 300 meters. Licence free radio operation.16 bit ADC resolution.