- Pickering Interfaces Inc.
product
PCI Resistor Card 2-Channel 1.5 Ohm To 8.19k Ohm
50-293-024
The 50-293 is a Programmable Resistor card with either two channels of 16-bit or four channels of 8-bit resistor chains in a single PCI card. The card is ideal for simulating sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
product
Multi-Platform Vehicle Test Set
Kratos Defense & Security Solutions, Inc.
The Multi-Platform Vehicle Test Set (MPVTS) is a self-contained portable equipment rack test instrument for performing vehicle electrical system verification. A custom MPVTS software application can be designed specifically to perform complete pre-mission verification of your airborne, ground, or marine vehicle. The MPVTS is the first test set designed to be completely vehicle platform independent.
-
product
PXI Resistor Module 4-Channel 1R to 63.7R
40-293-011
The 40-293 is a Programmable Resistor module with two channels of 16-bit, two channels of 12-bit or four channels of 8-bit resistor chains in a single 3U PXI module. The module is ideal for simulating sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
product
PCI Programmable Resistor Card 2-Channel 2.5 Ohm To 8.19k Ohm - SPST
50-294-124
The 50-294 series of PCI Programmable Resistor cards are available with two channels of 16-bit, two channels of 12-bit or four channels of 8-bit resistor chains in a single card. These cards are ideal for simulating sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
product
Engineering Design & Development
TPSA has over 20 years of experience in Engineering Design & Software Development including:Hardware & Software DesignOTPS Acquisition SupportSystems Installation & SupportAircraft Modification/CertificationEngineering Studies & AnalysesFunctional & Systems TestingIndependent Verification & Validation (IV & V)Test Program Set EngineeringReliability & Maintainability (R&M)Engineering Drawings & DataConfiguration Data ManagementReverse EngineeringRequirements AnalysisSupport Equipment (SE)Aircraft Launch & Recovery Engineering (ALRE)Engineering Change Proposal (ECP) ReviewTechnology Insertion (TI)PDR, CDR, FAT, Techeval, OSV Support
-
product
Waterproof Test Chamber
JL-XC
JL-XC series waterproof test chamber is mainly used for small electronic and electrical products. Such as lamps, electrical cabinets, electrical components and so one. The products are tested for physical and other related properties under simulated climatic conditions. After the test, it is judged whether the performance of the product meets the requirements by verification, so as to be used in the design, improvement, verification and factory inspection of the product. Comply with IEC60529:2001 《Degrees of protection provided by enclosures (IP Code)》, GB4208-2008 《Shell Protection Grade (IP Code)》 14.2.8 Terms and GB7000.1 《Lamps Part 1: General Requirements and Tests》 9.2.9 Terms.
-
product
PCI Resistor Card 4-Channel 1 Ohm To 510 Ohm With SPDT
50-293-114
The 50-293 is a Programmable Resistor card with either two channels of 16-bit or four channels of 8-bit resistor chains in a single PCI card. The card is ideal for simulating sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
product
Dial Torque Screwdrivers
A dial measuring torque screwdriver is designed for torque testing and torque verification. It is a versatile tool that is utilized for torque auditing and product evaluation. It can be used to monitor torque as it increases or decreases or display peak torque applied. The dial screwdriver is used in two common torque verification tests. One is the first movement test and the second is the loosening test. The screwdriver is standard instrument in engineer’s tool kit.
-
product
Advanced Circuit Card Automated Test
ACCAT
The ACCAT is designed to support diagnostic and acceptance test requirements across a wide spectrum of testing parameters. ACCAT provides a suite of core parametric test instruments, advanced GUI based software, Huntron Access Robotic probing and Huntron Analog Signature Analysis (ASA). ACCAT provides stimulus and asurement capabilities necessary for full functional and parametric testing of circuit card assemblies along with robotic guided probes for fault verification and debug. The Huntron ASA test is ideal for pretest or safe to power up procedures protecting the integrity of the test system.
-
product
PCI Express 5.0 and Compute Express Link Protocol Exerciser
Summit Z516
The Summit Z516 is a PCIe 5.0 and CXL protocol traffic generation test tool used for critical test and verification intended to assist engineers in developing and improving the reliability of their systems. The Summit Z516 can emulate PCI Express 5.0 and CXL root complexes or device endpoints, allowing new designs to be tested against corner case issues.
-
product
Manual Switch Boxes
RTI's manual switch box is a portable and versatile test solution for quick IC electrical verification tests. RTI's 96-pin manual switch boxes integrate with a variety of test configurations that are customized to your test and device needs. It requires no software and connects directly to an external power supply for bias test, and performs quick comparison tests using an A/B relay box.
-
product
Protocol Exerciser
Summit Z416
The Summit Z416 is a PCIe 4.0 protocol traffic generation test tool used for critical test and verification intended to assist engineers in developing and improving the reliability of their systems. The Summit Z416 can emulate PCI Express 4.0 root complexes or device endpoints, allowing new designs to be tested against corner case issues.
-
product
Adapters
BroadWave designs and manufactures Coaxial Adapters and other coaxial RF components that are ideally suited for test, verification and system integration. Our products offer consistent performance at a low cost with an emphasis on performance and configuration flexibility.
-
product
Continuous Time Interval Analyzer - PXI
GT668PXI-40
A true breakthrough in high-speed Time Measurement and test technology, GuideTech’s GT668PXI-40 leverages the power of its CTIA continuous time-stamping technology, eliminating the need for supplemental triggers, pattern markers or clock recovery circuits.GuideTech’s CTIAs enables serial interfaces pattern verification and full jitter analysis in milliseconds for fast, automated characterization and high-throughput production test on all ATE platforms, including low-cost and in-house testers.GT668PXI-40 cards can be expanded up to 36 Channels Single Ended Input in a single 3U PXI chassis.
-
product
Ethernet Protocol Analyzer
Investigator
Absolute Analysis Investigator features the most flexible, scalable and versatile instrument for protocol test and verification. The architecture is extensible to support multiple protocols and multiple test applications to meet the expanding requirements of various network topologies. CPRI, Serial RapidIO, Fiber Channel, Ethernet (10, 100, 1000, 10G), Serial FPDP, Custom military or secure protocols.
-
product
Handheld Test Instruments for HDMI
780 Series
The Teledyne LeCroy 780 series handheld test instruments for HDMI® are battery powered (except 780C, 780D and 780E), portable video and audio generators and HDMI analyzers that enable you to conduct quick, on-site verification testing and troubleshooting of your HDMI system and analog video displays. The 780 series instruments are equipped with both a reference source and a reference sink interface allowing you to test audio, video and protocols of any type of digital video device: sources, repeaters and sinks.
-
product
Modal Exciters & Amplifiers
Experimental modal analysis, or modal testing, is a process for physically obtaining a math model of a structure’s dynamic properties. Modal tests identify a structure’s modal properties: natural frequencies, mode shapes, mass, stiffness and damping. Modal test results help troubleshoot resonant excitation from operating forces, validate and verify finite element models, predict the benefits of structural modifications, support design verification, and understand structural responses due to complex loading conditions.
-
product
Variable Attenuator
FTBx-3500
Network equipment manufacturers and transceiver manufacturers know that variable attenuators are essential components of their test systems. They look for performance, user-friendliness, complete control of test parameters and advanced programming capability. EXFO’s FTBx-3500 Variable Attenuator combines innovative design techniques, high-quality components and meticulous calibration procedure. Ideal for bit error rate testing and system verification, the FTBx-3500 is the only variable optical a...show more -
product
PXI Resistor Module 2-Channel 2R to 131k with SPDT
40-293-134
The 40-293 is a Programmable Resistor module with two channels of 16-bit, two channels of 12-bit or four channels of 8-bit resistor chains in a single 3U PXI module. The module is ideal for simulating sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
product
LSI Functional Verification Services
SpecInsight
The keys to functional verification are “verification strategy” and “highly complete verification item extraction.” Our functional verification services emphasize highly complete verification item extraction while also generating test benches and functional scenarios, random verification, and even functional coverage to meet customer demands by providing these services from a wide variety of angles. By implementing functional verification on the RTL and C models designed by customers from a third-party perspective, we improve quality of customers’ circuits.
-
product
Fixture Kit
MF500
Electronic Test Fixture Kit Very low-cost kit facilitates use in situations where traditional fixtures are too expensive:o Research & Developmento Engineeringo Low-volume Production Uses include:o Debuggingo Programmingo Verification and Test
-
product
Hand-Held Test Solutions
RXT Series
With extreme modularity and an open platform concept, the RXT defines the test set of the future. The RXT''s capability to combine multiple technologies into a rugged modular platform increases the productivity of technicians who are responsible for the installation, verification, and maintenance of today''s complex services.
-
product
PXI Resistor Module 4-Channel 1R to 63.7R with SPDT
40-293-111
The 40-293 is a Programmable Resistor module with two channels of 16-bit, two channels of 12-bit or four channels of 8-bit resistor chains in a single 3U PXI module. The module is ideal for simulating sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
product
DC Blocks
BroadWave designs and manufactures DC Blocks and other coaxial RF components that are ideally suited for test, verification and system integration. With frequency ranges of DC to 18 GHz, our components offer consistent performance at a low cost with an emphasis on performance and configuration flexibility.
-
product
Bus Analyzer
Goebelyzer
Our Goebelyzer analyzer systems offer unparalleled insight into bus data and are used in flight test, system simulation, LRU design, verification and manufacturing test. Supported Interfaces Arinc 664, ASCB-D, Honeywell Flight Controls P2P, Arinc 429, CAN2.0b, Mil Std 1553, RS 422 SDLC/Async, ADC
-
product
PCI Programmable Resistor Card 4-Channel 2 Ohm To 63.7 Ohm
50-294-011
The 50-294 series of PCI Programmable Resistor cards are available with two channels of 16-bit, two channels of 12-bit or four channels of 8-bit resistor chains in a single card. These cards are ideal for simulating sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
product
Test Program Modules
The BRAT Test Program developed will provide functional validation of an assembly based on customer supplied documentation. This does not include hardware (e.g., Interface Test Adaptors), documentation (e.g., technical orders), travel or travel related per diem, or site verification test or installation.
-
product
PXI Resistor Module 2-Channel 2R to 131k
40-293-034
The 40-293 is a Programmable Resistor module with two channels of 16-bit, two channels of 12-bit or four channels of 8-bit resistor chains in a single 3U PXI module. The module is ideal for simulating sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
product
PCI Programmable Resistor Card 2-Channel 2.5 Ohm To 8.19k Ohm
50-294-024
The 50-294 series of PCI Programmable Resistor cards are available with two channels of 16-bit, two channels of 12-bit or four channels of 8-bit resistor chains in a single card. These cards are ideal for simulating sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
product
MCB Thermal Verification Test Bench
The test system is a special version of the thermal test test system in the sense that the test jig is primarily designed to hold and connect multi pole MCBs for thermal verification so that each pole can be verified to trip within the IEC time band after the MCB has been riveted. This test ensures the trip verification of MCB so as to trip all the 4 poles at once when overload is detected in one single pole. In short, this is a verification-only bench.
-
product
VME/VME64x Load Board
VECTOR Electronics and Technology, Inc.
The 6U VME and VME64x load board functions to test a system’s cooling capability by applying a variable load to the power supply for verification, then generating necessary heat to confirm the chassis’ cooling. This enables locating hot spots in the chassis so the airflow can be properly directed.