- Virginia Panel Corporation
product
VTAC Patchcord, Receiver, 36", VTAC, 2x 1000Base-T1 UTP Wire 1 Port MateNet, 1 Position
7-142716763-036
VTAC Patchcord, Receiver, 36", VTAC, 2x 1000Base-T1 UTP wire 1 Port MateNet, 1 Position.
-
product
Testing Large Radar Sensors with CATR Technology
CATR Radar Test System UTP 5069
Modern driver assistance systems must recognize increasingly complex traffic scenarios and convert them into appropriate vehicle reactions with the help of artificial intelligence (AI) and specific algorithms. Imaging radar sensors with a higher spatial resolution, so-called imaging radar sensors, are therefore required. These can better distinguish larger from smaller objects and, due to the larger antenna apertures, also require larger dimensions of the test environment or larger far-field dis...show more -
product
Power over Ethernet
PoE Tester
Covering both commercial and industrial applications, PLANET Power over Ethernet (PoE) products offer highly-dependable power and data transmission. Featuring 802.3bt standards, intuitive touch LCD design, Long Reach PoE technology over fiber optic cabling, coaxial cabling or UTP cabling, and PLANET exclusive intelligent PoE Management functions, all the requirements can be met for such applications as IP surveillance, IP communications, POS systems, PoE lighting and more. Our full range of PoE product lines include 95W 802.3bt PoE++/ 30W 802.3at PoE+ Managed Switches, Industrial flat-type PoE+ Switches, PoE Injectors, Splitters, Extenders designed for both indoor and outdoor environments.
-
product
Precise Testing & Simulation of A2B® Networks
A2B®-Component-Tester
The Automotive Audio Bus (A²B®) is a bus developed by Analog Devices Inc. for infotainment systems in automobiles. It is increasingly being used in other applications such as AV conferencing systems. Typical A²B® -products are Hi-Fi amplifiers/speakers, head units, eCall systems, microphones, vibration/noise suppression units, actuators, or sensorsCommunication happens via a simple two-wire UTP (Unshielded Twist Pair) cable. All A²B® -components are connected in a master/slave architecture to form a network. The complexity of audio systems in these A²B® -networks is reduced, and with it the cost and weight.
-
product
PXIe-8521, 4-Port, 100BASE-T1 PXI Automotive Ethernet Interface Module
786771-01
PXIe, 4-Port, 100BASE-T1 PXI Automotive Ethernet Interface Module - The PXIe-8521 is a 100BASE-T1 unshielded twisted pair (UTP) Automotive Ethernet interface for developing applications with the NI‑XNET driver. The PXIe-8521 is ideal for developing applications that require … Automotive Ethernet to test and validate automotive electronic control units (ECUs). The interface provides up to four independent endpoints or up to two network terminal access points (TAPs). It features onboard hardware t...show more -
product
Ethernet Media Switch
Ethernet media switch is a layer 2 switch running on Ethernet or Fast Ethernet. It equips with one or two fiber ports and four copper UTP ports and hence acts as easy-to-use add-drop equipment for connecting network devices into optical fiber network. Ethernet media switch meets corresponding IEEE 802.3 standards.
-
product
Cable Testers
The Tester can check UTP and STP Cat 5E,6,6A and Coaxial Cable. It can ldentify and locate the distance of a open or Short Circuit. With the Multifunction Tester you can determine the Continuity and Wiring of the Cable Pattern. Comes with the Low Battery Indicator. It uses TDR ( Time Domain Reflectometer ) to measure the length and distance of the cable. LCD Backlight Display.There are 8 Remote ID available.
-
product
Quintest
4400600
Tests UTP, STP & Installed Networks Tests & Verifies Short circuits, open circuits, pair reversals & miswires 2, 3 & 4 pair voice data channels Instant results via LED display Automatically tests for Screen Auto power off Low Battery Indicator
-
product
Glass Break Detection Sensor
ENVIROMUX-GBS
Acoustically detects the cracking of glass. Adjustable sensitivity. Includes mounting hardware. Connect to RJ45 or digital input sensor ports. Supports CAT5/5e/6 UTP or STP cables. Screw terminal. To connect to the RJ45 inputs use CAT5/5e/6 cable terminated at one end with RJ45 connector. Connect the un-terminated end to the sensor screw terminal. Maximum cable length: 1,000 ft (305 m). Powered by ENVIROMUX-2D/5D/16D.
-
product
UTP Software Suite
Increasing customer requirements, shorter product cycles and higher time to market demands dramatically influence the long-term goals in software development. With the Universal Test Platform Software Suite (UTP Suite), we introduce a robust standard that features a great set of tools for configuring, developing, analyzing, debugging and executing test sequences.
-
product
Universal Tester Platform
In order to meet these growing demands towards tester system NOFFZ has developed the Universal Tester Platform – UTP. The UTP 9010 series is the first scalable member of this innovative product family.
-
product
KIT for Test Cable Networks with Tools and Accessories
1RA370
Include: *Multi network cable tester for RJ45 (UTP / STP) and BNC*Modular crimping tool*LSA insertion tool*Cable stripper and cutter*30 units of RJ45 (8p8c) modular plugs*30 units of RJ11 (6p6c) modular plugs*24 units of colour strain relief*Comonents pocket*Zipper vinyl case
-
product
Quadruple Function Tester with Shielded HF Test Chambers
UTP 9011 RF
Circuit boards are the heart of all electronic devices. To ensure the reliable function of these boards, detailed tests are essential.Our board-level tester UTP 9011 RF works safely, quickly and cost-optimized at circuit board level. Our interchangeable adapters are particularly efficient in this system, with which you can even test different test items at the same time. The shielded NOFFZ HF test chamber always ensures consistently good results.
-
product
IVN-8561, Automotive Ethernet Interface Device
786169-01
2-Channel, 4-Port, 100BASE-T1 to 100BASE-TX Automotive Ethernet Interface Device—The IVN-8561 is an interface that converts 100BASE-T1 unshielded twisted pair (UTP) automotive Ethernet to standard 100BASE-TX Ethernet. It is ideal for developing applications that require automotive Ethernet to test and validate automotive electronic control units (ECUs). The IVN-8561 provides two channels to convert data between 100BASE-TX Ethernet and 100BASE-T1 Automotive Ethernet. Each 100BASE-T1 port can be configured as master or slave, using switches on the front panel. The IVN-8561 also provides LED on the front panel so that you can monitor the linkage and activity on the various ports.
-
product
CAT-5 Video Drivers
Analog Devices provides designers with a robust portfolio of high speed triple, differential, and single-ended input to differential output CAT-5 video drivers. We designed the technology for the highest resolution component video signals, but it can be used for any type of analog signals or high speed data transmission over either Category 5 UTP cable or differential printed circuit board (PCB) transmission lines. Manufactured with our second generation XFCB bipolar process, the drivers have large signal bandwidths of 700 MHz, fast slew rate, and output amplitude and phase matching balanced to –60 dB at 50 MHz.
-
product
8K ip Camera Tester M-IPC-450C with TVI 5.0 Audio, Wrist Design
M-IPC-450C
Fuzhou Metricu Technology Co Ltd
8K wrist tester M-IPC-450C supports 8K ip camera, analog camera, 8MP TVI camera, 8MP CVI camera and 8MP AHD camera. (5 in one)It also supports DC12V 3A, 48V PoE 25.5W power output, UTP cable, RJ45 TDR cable, RS485, Audio in, TVI 5.0 audio, wrist design, etc.
-
product
Parallel Testing of Multiple DUTs with High RF Channel Count
Test Rack UTP 7033 RF for validation
Our basic test rack UTP 7033 (33 rack units) is intended for equipping with various products and therefore for various application areas.The rack shown here as an example is prepared with products and measurement instruments to test automotive devices with high channel count.
-
product
Radar Test System
UTP 5065
Radar sensors are core elements to realize autonomous driving. The UTP 5065 radar test system from NOFFZ Technologies has a compact vertical design and contains everything needed to allow State-of-the-Art measurement and sensor calibration. The test bench setup and component selection are tuned to get best possible results for highly accurate and cost-efficient testing in production of automotive radar sensors.
-
product
Network Cable Tester
KT-95
Test device with UTP (Unshielded Twisted pair) ,STP (Shielded Twist Pair) and coaxial wiring ; Test with BNC and RJ45 socket. Test cable length, Check wire continuity, open, short, reversal and miswire. Main unit and one remote allow one person operate. Length Test Range:20m/200m/2km/20km Accuracy: À1% rdg À 0.3m. Self Calibrate available
-
product
Function Tester with Low Number of Channels
UTP 6010 RF
The UTP 6010 is one of our smallest test systems and therefore a cost-effective entry into our UTP tester series.The fast system is used to implement scalable functional test applications for a test item (single device under test) with multiple RF channels and mixed-signal test options. Depending on the adapter, the DUT can be tested at circuit board level (FKT) or when installed at the end of the line (EOL).Depending on the test item requirements, we configure the appropriate number of channels...show more -
product
VTAC Patchcord, Receiver, 72", VTAC, 2x 1000Base-T1 UTP wire H-MTD Cable Jack, 1 Slot
7-142716765-072
VTAC Patchcord, Receiver, 72", VTAC, 2x 1000Base-T1 UTP wire H-MTD Cable Jack, 1 Slot.Note: Static Bend Radius - 19.2mm [.76in], Flex Bend Radius - 48mm [1.89in]
-
product
Cable Management Tools and Testers
For anything compture repair and workstation installation tool, you've come to the right place. C2G carries a variety of cable tools and testers for network, coaxial, electrical, F-type, PC, telephone, and fiber cables. Our crimp tools are also available for RCA, BNC, F-type, RJ45, RJ11, RJ12, and flat ribbon connectors. C2G cable cutting tools can be used to cut a range of wiring types, from RG6 and RG59 coax, speaker wire, UTP network cable, flat ribbon, and more.
-
product
Smoke Detection Sensor - UL Approved, TAA Compliant
ENVIROMUX-SDS-TAA
For warning of smoke. Photoelectric smoke detector. Built-in 135° F (57° C) thermal heat sensor. Includes mounting hardware. Connect to RJ45 or digital input sensor ports. Supports CAT5/5e/6 UTP or STP cables. Voltage Supply: 8-35VDC. Current Consumption: 200uA. Alarm Output: Relay (NO). Screw terminal. To connect to the RJ45 inputs use CAT5/5e/6 cable terminated at one end with RJ45 connector. Connect the un-terminated end to the sensor screw terminal. Maximum cable length: 1,000 ft (305 m). Powered by ENVIROMUX-2D/5D/16D. Regulatory approvals: UL. TAA compliant.
-
product
Ethernet Media Converter
A physical layer equipment which interconnects the Ethernet, Fast Ethernet, or Gigabit Ethernet on copper UTP and the related fiber optics network. Ethernet media converter meets corresponding IEEE 802.3 standards.
-
product
Automotive Ethernet Interface Device
The Automotive Ethernet Interface Device converts unshielded twisted pair (UTP) Automotive Ethernet to standard Ethernet. This device is ideal for developing applications that require Automotive Ethernet to test and validate automotive electronic control units (ECUs). It includes ports for Automotive Ethernet connections and ports for 100BASE-TX Ethernet connections. You can use switches on the front panel to configure each 100BASE-T1 port as master or slave. The device also provides LED on the front panel so that you can monitor the linkage and activity on the various ports.
-
product
UTP Cable Tester
21-8574-00
The Lan Cable Tester is consists of unshield RJ45:568A, 568B & USOC. The tester also easy to operate, the user begins testing by connecting. The multiple LEDs showed indication. This Lan Cable Tester is very practical tester can be easily read and correct pin configuration of cable continuity, open, short, miswiring, & no connection.
-
product
PXIe-8523, 4-Port, 100/1000BASE-T1 PXI Automotive Ethernet Interface Module
787311-01
PXIe, 4-Port, 100/1000BASE-T1 PXI Automotive Ethernet Interface Module - The PXIe-8523 is a 100/1000BASE-T1 unshielded twisted pair (UTP) PXI Automotive Ethernet Interface Module for developing applications with the NI‑XNET driver. With this hardware, you can develop applications … that require Automotive Ethernet to test and validate automotive electronic control units (ECUs). The PXIe-8523 provides up to four independent endpoints or up to two network terminal access points (TAPs). It features...show more -
product
Smoke Detection Sensor - CE Approved
ENVIROMUX-SDS-CE
For warning of smoke. Photoelectric smoke detector. Smoke sensitivity: 0.08-0.14 dB/m. Built-in 135° F (57° C) thermal heat sensor. Includes mounting hardware. Connect to RJ45 or digital input sensor ports. Supports CAT5/5e/6 UTP or STP cables. Screw terminal. To connect to the RJ45 inputs use CAT5/5e/6 cable terminated at one end with RJ45 connector. Connect the un-terminated end to the sensor screw terminal. Operating temperature: 14 to 122°F (-10 to 50°C). Maximum cable length: 1,000 ft (305 m). Powered by ENVIROMUX-2D/5D/16D. Regulatory approvals: CE, RoHS.
-
product
Software Suite for Automated Test
UTP Automated Test
Increasing product complexity, centralized test data management and different hardware platforms from different manufacturers – these are typical challenges of test software developers for which we offer specific solutions.Our test software solution is based on certified development environments such as NI TestStand, NI LabVIEW and .NET. Thanks to our expertise based on more than 30 years of experience, we have managed to create a hardware abstraction layer that serves hardware and software deve...show more -
product
Hand-held Cable Tester
STM-8
The STM-8 is an economical and versatile hand-held tester designed for the testing of UTP and screened cable for opens, shorts, reversals, miswires, split pairs and cable length.
-
product
CAT-5 Video Receivers
Analog Devices high speed, differential CAT-5 video receivers and equalizers compensate for the transmission losses of UTP and coaxial cables up to 300 meters in length. Various gain stages are summed together to best approximate the inverse frequency response of the cable. Logic circuitry controls the gain functions of the individual stages so that the lowest noise can be achieved at short-to-medium cable lengths. Our video receivers provide excellent common-mode rejection that enables the use of low cost, unshielded twisted pair cables in noisy environments.
