- Pickering Interfaces Inc.
product
PXI Resistor Module 2-Channel 2R to 16.3k with SPDT
40-293-131
The 40-293 is a Programmable Resistor module with two channels of 16-bit, two channels of 12-bit or four channels of 8-bit resistor chains in a single 3U PXI module. The module is ideal for simulating sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
product
Advanced SoC/Analog Test System
3650
Chroma 3650 is an SoC tester with high throughput and high parallel test capabilities to provide the most cost-effective solution for fabless, IDM and testing houses.
-
product
Faraday Chamber for RF w/Exchangeable Cassettes 340x350mm RCV 9025 for 6TL36
AN133
The Faraday Chamber is an add-on for the 6TL36 test handler. This kit is installed into the 6TL36 in the same way a normal test fixture would be installed, being the only difference the fact that different products to be tested will, from that moment on, only need an additional exchangeable cassettes to be tested.
-
product
Active Alignment Assembly & Test Platform
Quickly deliver flawless camera & LiDAR modules, MEMS devices, die based sensors, LED and laser-based headlights and other high-end products with a supremely accurate standardized platform.
-
product
Regenerative Battery Pack Test System
17040
Conforms to international standards for battery testing: IEC, ISO, UL, and GB/T, etc.Regenerative battery energy discharge (Eff. >90%, PF >0.95, I_THD <5%)Multiple voltage and current ranges for auto ranging function to provide optimum resolutionHigh accuracy current/voltage measurement (0.05%FS/0.02%FS)2ms current slew rate (-90% ~ 90%)Dynamic (current/power) driving profile simulation tests for NEDC, FUDS, HPPCTest channel parallel functionTest data analysis functionData recovery prot...show more -
product
Test Lamp
TL105
The TL105 is a battery operated test lamp designed specifically to test General Monitors Flame Detectors. The TL105 is an explosion-proof test lamp that can be used with the FL4000H MSIR flame detector as well as any of the FL3100 Series Flame Detectors.
-
product
Test Equipment
Concentric Technology Solutions, Inc.
If you are looking for a Bluetooth, RFID, or DMB/DAB test equipment, Concentric Technology Solutions, Inc. (CTS) have the right tester for your testing needs. Our testers give our clients all the right features you need – whether it’s full compliance testing or just to test functionality. CTS has the solution to meet your needs.
-
product
AC Hipot Test Set
Weshine Electric Manufacturing Co., Ltd
AC Hipot Test Equipment for Dielectric Withstand Test are suitable for 50 / 60 Hz AC testing of low capacity test objects. Optionally, these units can also be upgraded to function as DC test sets by mounting the rectifier attachment on top of the transformer.Weshine® AC Hipot Test Set for AC hipot test can be equipped with a rectifier attachment for DC voltage testing.Typical application areas:Testing of cables Testing of switchgearTesting of transformersTesting of CP & PTTesting of MV systems
-
product
IEC61588 And IEC60065 Mandrel Test Apparatus
CX-M01
Shenzhen Chuangxin Instruments Co., Ltd.
IEC61588 and IEC60065 Mandrel Test Apparatus is designed and manufactured in accordance with the standard requirements of IEC61558 and IEC60065. The IEC61588 and IEC60065 Mandrel Test Apparatus is used for the insulating thin layer of the power transformer and supply unit as well as the similar products to do the spindle test, mechanical strength test and abrasion test.
-
product
Test System
Maynuo Electronic Co.,Ltd a professional R & D and production of programmable DC electronic loads, programmable DC power supply, high power load, power supply, AC power supply, power supply, such as testing high-performance mobile phone test equipment and facilities, as well as electrical, electronic, aerospace, military, chemical, automotive, battery charger, battery, solar cell production lines and other industries to provide automated testing program. The company has many years experience...show more -
product
Speaker Test
Determines speaker polarity by analyzing a proprietary signal. See our new demo video of this module. Measures woofers, midrange, and tweeter drivers.
-
product
Threaded Probes Designed for Connector and Harness Test
Equip-Test Threaded Probes Designed for Connector and Harness Test
-
product
Automatic Hysteresis Graph Test System
DX-4DMT
X-4DMT automatic hysteresigraph system accords with the standard permanent magnet test system, GB3217-92, used to measure the major and minor hysteresis loops, demagnetization curves, recoil hysteresis loops and initial magnetization curves in different temperature of ferrite, AlNiCo, SmCo, NdFeB and quenched material, and gives the magnetic parameter, Br, Hcb, Hcj, (BH)max, Hk and so on, and could meet different requirements on test function, precision, power capability, reliability, efficiency, price, local environment from laboratory to enterprise's production line.
-
product
Saluki S87234 Series USB Peak and Average Power Sensor (max. 67GHz)
S87234D/E/F/L USB peak and average power sensor is a diode-detection broadband power measurement instrument based on the USB 2.0 interface, which can realize accurate average power measurement, pulse power measurement with large dynamic range and CCDF statistical measurement analysis. The frequency range covers 50MHz to 67GHz, the highest power accuracy can reach 0.2dB, the video bandwidth is ≥30MHz, and the rise/fall time is ≤13ns.S87234 series can flexibly expand the power measurement function of electronic measuring instruments and test systems, and is mainly used for field testing, production line testing and system integration.
-
product
Panel Test Solutions
C.C.P. Contact Probes Co., LTD.
CCP offers special rounded pins and test modules for panel testing.
-
product
Passive Fiber Network TAPs
Passive network test access points (TAPs) are a hardware tool that allows you to monitor your network. Garland Technology offers fiber network TAPs in network speeds of 1Gb, 10Gb, 40Gb and 100Gb. Fiber Network TAPs are passive, purpose-built hardware devices that make a 100% copy of your networks data - without affecting network traffic. Passive network TAPs let your monitoring tools to see every bit, byte and packet®.
-
product
Smart Manufacturing Solutions
The integration of the physical and virtual worlds and the speed of technological change are just two of the challenges facing manufacturers today. Industries undergoing a digital transformation, including IoT and the merging of IT and OT, are rapidly reshaping the manufacturing landscape. Don’t fall behind! Let our test expertise and extensive knowledge of ATEs confidently guide you through this new market reality.
-
product
International Test Set
930i
The 930i Communications Test Set is a multi function portable unit that features a powerful Next Generation Voice Test Suite. It offers a laboratory quality VF TIMS, a full-featured BERT, RS-232 control and a host of other functions as standard equipment.
-
product
HALT/HASS Testing
HALT HASS Chamber
AST applies stresses (such as temperature and vibration) to products well beyond its normal use environment. This type of testing is done to determine product operating and destruct limits. These stresses are applied as the product is functionally tested and continuously monitored for failures.Highly Accelerated Stress Testing (HALT) and Highly Accelerated Stress Screening (HASS) are two types of accelerated stress testing. These types of tests are commonly used to eliminate design problems, helping to develop a robust, mature product prior to market introduction. It can also be used to screen out infant mortality issues prior to shipment.
-
product
Breaking Force Testers
Break Force Tester is applied for break force test of the ampoule, lipstick, lip cream and other materials.
-
product
Catena 1910 HSIC Tester
Catena 1910
The MCCI Catena 1910 HSIC USB Tester enables testing of HSIC Host or HSIC Device products. It can be used to exercise your product by operating as an active host or active device, while simultaneously capturing USB traffic for analysis. For test and validation of a final system, Passive Capture mode lets you debug and verify communication between your HSIC Host and HSIC Device,
-
product
Climatic Temperature/humidity Chambers
PV-K Series
The PV-K Series climatic temperature/humidity chambers (Espec Corporation - previously Tabai Espec) can be combined with G-0N & G-9 Series Vibration Test Systems for combined environmental tests of temperature/humidity and vibration for various parts, components and units.
-
product
Phase Noise Analyzer
NXA-26
This new NXA-26 is a sea-change in Phase Noise Test Systems. Making both residual and absolute noise measurements out to 26.5 GHz, this self-contained instrument uses either internal or external references with cross correlation for maximum dynamic range. The NXA-26 combines over 25 years of Phase Noise Measurement Technology with an easy to navigate user interface. System operation requires minimal training that will have you making measurements in minutes.
-
product
DC Electronic Loads
Keysight DC electronic loads provide you with the flexibility to test a wide range of applications from power-supply test to simulation of high-intensity discharge (HID) headlamps. The 16-bit voltage, current and power-measurement system provides both accuracy and convenience, and eliminates the need for a DMM, external shunts and wiring.
-
product
ELM Electronic Load Module
Circuit breakers are often overlooked during maintenance of electrical systems in aircraft, or often only verified for open and closed states. To test the true functional purpose of a circuit breaker it requires the application of current in excess of the rated trip value and then measure the time for the breaker to actually trip. This is the only way to verify that a circuit breaker will react as designed if an electrical failure occurs.
-
product
New 12v Battery Load Tester
Hangzhou Xun Anda Electrical Co., Ltd.
battery maximum capacity: 120Ah or 1200CCA(SAE)voltage test range: 7-15VDCoperating voltage: 7-15VDC , storage battery power suppliedmaximum power dissipation: 0.5W aroundoperating temprature: -10°C~50°C;operating humidity: 30%~90% (without condensation)display modes four super bright nixie tube with 0.56 inch ,four different color Led indicator lightkeying: three keying total for using related operation
-
product
Research & Electronic Test Products
he CAL-AV Research & Electronic Test Product line includes Explosive Test Site Range Instrumentation, Illuminated Laser Warning Signs and Special Projects.. Firesets, CDU’s EDU’s, Delay generators, firing panels, and custom instruments. Fiber-optic and computer-control options.
-
product
DC/AC High Current Probe
698
Unit is designed for use with digital multimeters,lab scopes or graphing meters. With 1000 Amp capabiltiy, this instrument can be used to test starting and charging systems. It can even be used to test relative compression when used with your lab scope or graphing meter.
-
product
GenRocket TDG System
TDG can generate the test data you need to test your application before shipping to production. No need to wait for production data.
-
product
Electronic Crockmeter
UI-TX51
Electronic Crockmeter (Crock Meter) is used to test color transfer of colored textile (leather, fabric and etc,) to other surface due to rubbing. It is test of colour fastness to rubbing, one of physical testing of textiles.