-
product
3 GHz RF/IF Sentinel Intelligent Signal Scanning Portable Recorder
Talon RTR 2613
The Talon® RTR 2613 combines Pentek’s Sentinel Intelligent Signal Scanning software with real-time recording in a lightweight, portable and rugged package. The RTR 2613 provides SIGINT engineers the ability to scan the 3 GHz spectrum for signals of interest and monitor or record bandwidths up to 40 MHz wide once a signal band of interest is detected. The RTR 2613 recorder is a grab-and-go recorder suitable for test & measurement, mobile military, security and government intelligence (SIGINT, COMINT and ELINT) applications.
-
product
Temperature Rise Test Panel
2000A
SCR ELEKTRONIKS have developed “TEMPERATURE RISE TEST BENCH FOR MEDIUM VOLTAGE SWITCH BOARDS” to measure rise in temperature at various points as mentioned in standard at junctions. The set-up consists of a True RMS Constant Current Source (to maintain the Current within + / - 1 % of set value with Digital Indication), PC based control system, Temperature data logging on PC, Servo-Controller and other indications. Digital voltmeter Primary Voltage) indicates the position of auto transformer (variac).
-
product
Leakage Current Tester
M450LT
Performs leakage current tests in compliance with IEC 601, UL 544, UL 2601 and other medical and non-medical standards. Add Rod-L Hipot & Ground Continuity testers to build a complete modular automatic test systerm
-
product
Servo Motor ,Precision Linear Stages
PSAXXX-11AS-X
Model:PSAXXX-11AS-X Servo Motor ,Precision Linear Stages PSAXXX-11AS-X adopt panasonic 100W or 200W AC servo motor and high level coupler,achieve high resolution,high speed,low vibrate;material is alluminum alloy by special craft; Characteristic ◆ground ball screw ,achieve high postion accuracy ◆import guide ensure straightness and parallel inconjunction with our special craft ◆strict assemble craft and test method, ensure high performance ◆servo-motor and limited swithes design, convenient for choosing controller ◆limited switches ensure safety ◆different size and travels,make products abount ◆hand-wheel achieve hand adjustment
-
product
Dial Indicators
1. Always select the dial test indicator that best fits the application.2. Care should be taken while using a dial test indicator, try not to jolt the indicator, should you be unfortunate and drop a dial test indicator, get it re-calibrated/repaired before reusing it.3. Replace worn contact points only with those of a similar length from the centre of the ball stylus to the abutment shoulder.4. Always clean dial test indicators after use with a lint free paper or cloth and store the indicator in...show more -
product
PXI Switched Guard Reed Relay Module, 26x SPST
40-121-001
The 40-121-001 provides 26x SPST switches in a single slot PXI module and designed to provide an isolation resistance in excess of 1013Ω. It has been designed to ensure high isolation resistance through the use of switched guards, making it ideal for low level measurements and semiconductor test.
-
product
Ground Network Earth Resistance Tester
HTDW-5A / 736
Wuhan Huatian Electric Power Automation Co., Ltd.
It is suitable for the test of grounding resistance of large power grid in power departments, substations and other institutions.
-
product
PCI Precision Resistor Card 3-Channel, 3Ω To 22.3MΩ
50-297-154
The 50-297 provides a simple solution for applications requiring accurate simulation of resistive sensors. The 50-297 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems. It is particularly well suited to applications such as the testing of engine controllers where resistive sensors provide information on parameters such as temperature.
-
product
Self-Sufficient Test System
MFTS100
Computer Gesteuerte Systeme GmbH
The MFTS100 is a self-sufficient test system with optional integrated touch screen for easy operation and display of measurement data or running processes.
-
product
OTA Chamber for 5G NR mmWave Signals
ATS1800C
The R&S®ATS1800C CATR based 5G NR mmWave test chamber provides the ideal environment for testing 5G FR2 antennas, modules and devices over the air (OTA) from R&D to conformance. With its small footprint and wide frequency range, the R&S®ATS1800C offers great functionality and test coverage in a very small space. With its flexibility and broad range of extension options, the R&S®ATS1800C offers a solid and future-proof environment for your FR2 testing needs.
-
product
Radiographic Inspection Test
The radiographic inspection is a non-destructive x-ray method for detecting internal physical defects in small component parts which are not otherwise visible. Radiographic techniques are intended to reveal such flaws as improper positioning of elements, voids in encapsulating or potting compounds, inhomogeneities in materials, presence of foreign materials, broken elements, etc.
-
product
G12x - 18 Module Solution
The G12x Receiver has four removable rubber feet below the platform and also allows for permanent tabletop mounting. Available with 15" or 20" platforms. The G12x accepts ITAs designed for both the G12 and G12x allowing versatility with your test system.
-
product
In-Circuit Testing and Test Engineering
Teradyne Z1890
2048 Pure Pin Test Nodes3 & 6-wire Analog MeasurementsVector Test for VLSI, PLCC’s & ASICSMultiscan II Vectorless TestingIEEE Functional Interface BoardLarge Custom Vector Library
-
product
Modulation Distortion Up To 90 GHz
S930709B
S930709B enables fast and accurate active device modulation distortion characterization under modulated stimulus conditions up to 90 GHz. The wide dynamic range and vector error correction of the PNA-X results in an extremely low residual EVM of the test setup, delivering you a complete picture of your device’s performance without test system interference. S930709B measures EVM, NPR, ACPR, and decomposes nonlinear signals and linear signals with the spectral correlation between input and output spectrum without doing demodulation. Integration with the PNA-X SCCM provides quick modulation distortion measurements while making other VNA measurements.
-
product
Shoe Dielectric Resistance Tester
UI-FT07
Shoe Dielectric Resistance Tester, also named as shoe high voltage withstand tester, is used to test shoe sole and heel electrical insulation, to check shoe performance of voltage withstand and current leakage. It is to test safety shoe dielectric resistance ability (Electrical Hazard Testing) as mentioned in ASTM F2412.
-
product
Partial Discharge Meter
TMG
The partial discharge meter TMG was developed for Partial Discharge tests according to VDE 0434 and IEC 60270.
-
product
The all-in-one data logger for the entire vehicle networking
PM-200
The PM-200 sets the bar considerably higher on the topic of safeguarding and troubleshooting vehicles. Bus systems such as CAN, CAN-FD, FlexRay™, LIN, MOST150 and Automotive Ethernet are logged at a data speed up of to 120 MB/s. SSD removable media allow for quick evaluation and distribution of the data. Various upgrade options enable configuration for any application. Flexibility, programmability and support from debugging protocols make it possible to meet the high demands of functionality and fleet tests as well as of test runs.
-
product
Model Based Testing
RTT-MBT
Verified Systems International GMBH
The RT-Tester Model Based Test Case and Test Data Generator (RTT-MBT) supports model-based testing (MBT), that is, automated generation of test cases, test data, and test procedures from UML/SysML models. Moreover, it generates traceability data relating requirements, test cases, test procedures, and results.
-
product
Hall Effect Measurement system
HMS-3000
Hall Effect Measurement System is very useful for measuring Carrier Concentration, Mobility, Resistivity and Hall Coefficient that should be pre-checked in order to grasp the electrical specifications of semiconductor device. Therefore, it is essentially required system to understand the electrical characteristics of semiconductor device.Ecopia’s HMS series consist of constant current source , terminal conversion system by Van der Pauw technique, low temperature(77K) test system and magnetic flux density input system. So, it is well-established system that has all the things needed to Hall Effect Measurement System.
-
product
Multimeters
Wuxi IMHOO Technology Co., Ltd.
Large LCD for easy readingWith double fuse, safe and reliableWith frequency test function
-
product
Desktop Test Interface Station
2210
TESCO’s new Desktop Test Interface Station (Catalog No. 2210) provides metering professionals with exceptional testing flexibility. The Test Interface Station is ergonomically designed for meter technicians working in a lab or a desktop, yet still rugged for field use. The Test Interface Station includes a zero insertion force (ZIF) meter socket, voltage selection, form selection, open/closed-link selection and bi-directional cabling to power a load box/test kit & connect test standard poten...show more -
product
PoE PD Test Solutions
Explore PoE PD Test solutions from Sifos Technology. What type of testing does your Power-Over-Ethernet Powered Device need?
-
product
Multiport Electromechanical Coaxial Switch, DC to 40 GHz, SP4T
87104D
The Keysight 87104D multiport switch improves signal accuracy in RF and microwave signal routing and testing applications. This high performance electromechanical switch provides unmatched isolation and a 0.03 dB insertion loss repeatability, which is warranted for the 5-million life cycle of the switch. The 87104D’s low insertion loss repeatability reduces sources of random errors in the measurement path, which improves measurement accuracy. The repeatability and reliability of this switch guar...show more -
product
Automated Shock Test Systems
AutoShock-II Test System
The AutoShock-II is a fully automated series of shock test systems used to measure and identify product fragility levels and evaluate protective packaging. With the simulation of real world shock pulses and impact energy levels, manufacturers can systematically test and optimize product design and packaging. L.A.B. Equipment, Inc.''s fully automated computer controlled shock and data analysis test systems are the critical path in accomplishing this optimization.
-
product
Plug and Switch Testing
Applied to test electrical accessories heating conditions when connected to load current, whether the temperature rise of electrode is compliance with standard requirement or not. And it can effectively detect whether the plug bush is slants thin and whether plug and socket cooperated with all right.
-
product
Optical power meter with Optical laser Source
Shanghai Baudcom Communication Device Co.,Ltd.
The Multimeter combines a power meter with a 2-wavelength laser source,for optical fiber network installation and maintenance. With the large capacity of data storage,it's very convenient for field testing and transfering the test results to PC through USB interface.
-
product
Digital (1kV below) Insulation Tester
2801 IN
Standard Electric Works Co., Ltd
● Microprocessor-controlled with advanced safety features.● Three test voltages : 250 / 500 / 1000V.● Displays and sound warning if external voltage present.● Ener-Save™ feature to extend battery life.● Continuous battery monitoring.● Auto ranging / auto-null / auto-off.● Insulation tested at 1mA.● Built-in carry case, test leads in separate pouch.● Real-time barg-raph display of test voltage and voltage decay during discharge.● Audible and visual message displayed if external voltage is present.● Large LCD.● Display can be customized for special orders.● Continuity buzzer.● Show test time duration (up to 99.9s) for easy comparison.● BS 16 edition.
-
product
PXIe-2725, 8-Bit, 18-Channel PXI Programmable Resistor Module
781986-25
8-Bit, 18-Channel PXI Programmable Resistor Module - The PXIe‑2725 is a test module that replicates the behavior of resistance-based inputs and outputs such as potentiometers, resistance temperature detectors (RTDs), voltage dividers, and bridge elements. The PXIe‑2725 programmatically controls a series of relays to vary the resistance across each channel of an I/O connector. This function is well suited for simulating environmental conditions in hardware‑in‑the‑loop (HIL) validation. The software provides a simple user interface that accepts inputs in units of temperature or resistance and configures the resistance across each channel.
-
product
Electro Fatigue Testing Machine
EPS Series
Jinan Testing Equipment IE Corporation
EPS series Electro Fatigue testing machine are fast acting table-top testers ideally suitable for performing static and dynamic fatigue tests on a variety of materials and components. These electro-dynamic machines use a linear electric motor with an adjustable upper cross-head of a stiff dual column frame. The electro-dynamic actuator is connected to single phase power, which resulting in a clean low maintenance solution. With dynamic force capacities, the Electro Fatigue testing machines are used to evaluate the mechanical properties of biologic materials, composites, orthopedic fixation devices, prostheses, spinal constructs, stents, dental implants, elastomeric materials and others.
-
product
Titan Data Acquisition
DAQ
Titan Data Acquisition (DAQ) Systems offer universal signal conditioning, low power consumption, convenient SD card storage, and easy-to-use software. Systems can be purchased as a complete test kit, including custom cables and accessories. Titan products are designed and built in the US.
