-
product
Flying Probe Tester Substrate
Substrates with structures down to 10µm and several hundred thousand test points per panel require specific solutions forscanningcapacitance measurementhigh accuracy and temperature Management
-
product
DC Insulation Testing
Diagnostic insulation testing today represents over a hundred years of constant development. When Sydney Evershed pioneered the first insulation tests in the late 19th century, the only measurable values were insulation at 500 volts and a basic continuity check. However, measurement techniques have continuously evolved to keep pace with new insulation technologies. From electronic design and household wiring to generators and power transmission systems, all different kinds of insulation must operate at a safe minimum value.
-
product
Active Filter
J2190A
The J2190A active filter presents a high impedance (approximately 150kOhms) minimizing the loading of the circuit being tested. The output impedance is 50 Ohms allowing low noise coaxial connections to all typical test equipment. The 0.1Hz-10Hz noise band is common for opamp measurements, voltage regulators and voltage references. Many application notes offer schematics of such a filter for test purposes. An engineer’s time is much too valuable to be spent building test equipment. We have created a 4th order high pass and 4th order low pass filter with an optimally flat response and 0dB gain. Additional filters can be cascaded for even sharper cutoff.
-
product
Voltage Variable Attenuators
a High Reliability Low Noise Voltage Controlled Oscillator (VCO) which covers a 10 MHz to 20 MHzfrequency band with a voltage tuning range from 0V to 20V. This design features exceptional phase noise performance of -120dBc/Hz @ 10 kHz offset. Supply Voltage is +15V with a generated output power level of +10 dBm and 2nd harmonic output of-11 dBc typical. The assembly is RoHs compliant and available in a compact 0.5 inch SMT package with an industry standardmounting footprint. The bottom surface i...show more -
product
Flying Probe Tester
FA1817
Flying Probe Tester FA1817, an automatic testing system designed to inspect printed wiring on bare boards. The FA1817’s features and capabilities make it ideal for use in inspecting high-density printed wiring boards. With support for a broad range of test types, from low-resistance measurement to high-insulation-resistance measurement, the system reliably detects the latent defects that trouble end-users.
-
product
UART Protocol Exerciser and Analyzer
PGY-UART-EX-PD
Prodigy Technovations Pvt. Ltd.
UART Protocol Analyzer (PGY-UART-EX-PD) are the Protocol Analyzers with multiple features to capture and debug communication between host and design under test. PGY-UART-EX-PD is the leading instrument that enables the design and test engineers to test the respective UART designs for its specifications by configuring the PGY-UART-EX-PD as Master/Slave, generating UART traffic and decoding the UART protocol decode packets.
-
product
Battery Testing Machine
Dongguan Kejian Instrument Co., Ltd.
Test method is to use test sample cell on a plane, a diameter of 15.8 mm (5/8 inch) rods on the cross placed in the center of the sample.one 9.1 kg or 10 kg weight from a certain height (610 mm or 1000 mm) fell to the samples.Cylindrical or square battery in accepting the impact test, the vertical axis parallel to the plane, vertical steel column longitudinal axis.The longest axis vertical steel column square battery, the bedding face perpendicular to the direction of impact, each battery only accept an impact test.
-
product
Test-Kits
Hach offers a wide range of kits - from easy-to-use, single parameter color comparators to comprehensive portable laboratories with state-of-the-art instrumentation - for fast and accurate results both in the field and in the laboratory. The areas of application include drinking water, waste water, boiler water and much more. Hach test kits include everything you need to get started with your determinations right away. This includes the necessary equipment and a complete set of reagents, all in a sturdy Hach transport case.
-
product
RJ-50 Test Connector
Test solution for RJ-50 connectors (10 pole). Applications in data networks, data transmission, power supplies, microphones, etc.
-
product
VITA 57.4 FMC+ HSPC Loopback Card
Samtec's VITA 57.4 FMC+ HSPC Loopback Card provides FPGA designers an easy to use loopback option for testing low-speed and high-speed multi-gigabit transceivers on any FPGA development board or FPGA carrier card. It can run system data or BER testing on all channels in parallel. This makes evaluation and development with an FPGA much easier and is an ideal substitute for 28 Gbps test equipment.
-
product
Multi-Channel Attenuation Control Unit (5-channels), DC to 18 GHz, 0 to 121 dB, 1 dB Step
J7205B
The J7205B is a multi-channel (5-channels) attenuation solution for signal attenuation and conditioning of up to 5 devices under test (DUT). Operating frequency from DC to 18 GHz, with 121 dB, 1 dB steps. Exceptional 0.03 dB insertion loss repeatability per section for the entire 5 million cycles and excellent attenuation accuracy and flatness, the J7205B reduces cost of ownership and provide the best measurement accuracy.
-
product
Pump Test System
This automated test system evaluates a wide range of performance metrics for a cooling pump assembly. The LabVIEW based system programs the DUT then initiates a series of tests to check:Serial communication verificationMotor voltage & currentImpeller speed and flowAir and water temperaturesLeak and level sensor functions
-
product
Explosive Atmosphere Testing
A product that is designed for or could potentially be placed in a hazardous, explosive environment must be evaluated, especially if it could cause the environment to ignite. This is imperative for products that operate within engine compartments, electrical panels that are mounted in adverse environments, pumps and much more. We can test using almost any mixture of propane or hexane gas and can support these tests with altitudes up to 50,000 ft. If you are concerned about your product’s potential risks, see us about putting your test plans in action.
-
product
Logic Analyzer
GoLogicXL-36
Logic analyzers and oscilloscopes offering fast sample rates and large memory depths are required to debug and test modern electronics. The GoLogicXL captures a very large window of bus activity using sample depths up to 1 billion samples. 4 GHz sampling rates expose the finest details in your signals. 1 GHz Transitional sampling provides the optimum method to capture fast data bursts separated by seconds, minutes, or even hours of bus inactivity. The GoLogicXL State analysis can also synchronize with single-data-rate 300 MHz SDR clocks, and double-date-rate 250 MHz DDR clocks (500 MHz effective).
-
product
Cable Length Meter
Shanghai Beha Electronics Co., Ltd.
*Cable length measurement by pulse reflection measurement, only required one cable end (with two wires)*Resistance measurement*Acoustic continuity test
-
product
Modular Test System
A modular test system, RTS (real time scanner) provides instant test results with minimal interface cables to check wiring during installation.It tests wire harnesses in real time using our micro switching technology, reducing the need for high cost interface cables by around 90%. an innovative best-in-class solution for FAL testing, RTS also offers many benefits for wire harness and sub-assembly manufacturers.
-
product
Unbalance Tester
BK2027
If you need to test displacement in hard drive motors with speeds up to 10,000rpm, think about BaKo's Type BK2027 Unbalance Tester. It's both easy to set up and easy to use and as a 2 channel DSP based system, it can test 2 motors at once and display the balance results as either unbalance (cm.g), acceleration (m/s2) or vibration strength (g).
-
product
Network Testing
UX Series
The VeEX UX series includes the robust UX400 and UX400R Universal Expert platforms. The UX400 is the most versatile portable multi-service transport test solution to offer a wide range of modules with test capabilities ranging from DS1/E1 all the way up to the latest 100GE and OTU4 network speeds, for a total of up to 600G traffic generation in a single compact modular chassis. Available in Portable and Rack-mount versions.
-
product
Keypad Test system
Mistral
Engineering Solutions Inc. (ESi)
The Mistral Keypad Test System has been designed to be the least expensive, easiest to use full featured tester for membrane switch assemblies. The idea is to combine a small, smart "pod" with a PC running software that makes full use of the Windows® graphical interface. Make it as easy to set up and use as possible yet include all the features you need.
-
product
Multi-Cal Pressure Calibrator
MC
Series MC Portable Multi-Cal Pressure Calibrator performs a wide variety of simple and complex pressure based measurement, test, and calibration operations. Modular sensor design allows user to select pressure measurement range for application flexibility.
-
product
Tap Changer Analyzers & Winding Ohmmeters
Winding resistance test of inductive test objects, such as power transformers, is one of the most effective non-intrusive ways of checking its condition. Due to their advanced design, DV Power winding resistance meters provide high test currents (up to 100 A DC) and high accuracy (up to 0.1%) within light and portable test instruments. In addition to winding resistance measurement, it is also possible to perform simple, quick and reliable transformer on-load tap changer condition assessment by r...show more -
product
ARINC-664 Part 7 Test and Simulation Board
EXC-664PCIe
The EXC-664PCIe board is an ARINC-664 part 7 test and simulation board designed to help integrate avionics suites, and can simulate up to two ARINC-664 P7 End Systems with full dual redundant support for receive and transmit operation. The board also contains room for two standard 4000 modules that can support multiple channels of other avionics communications protocols including MIL-STD-1553, ARINC-429, Serial, Discrete, ARINC-708 and CANbus.
-
product
Multimode LAN Test Kit
KI-TK052
Multimode LAN test kit for low to modest test volume & some SM capability.
-
product
Residential Combustion Analyzer
C161
UEi Test & Measurement Instruments
Backed by UEi Service+ to give up to 6 years’ warranty, next day recertification, and a reduced cost of ownership. The C161 Residential Combustion Analyzer is easy to use with a rugged design, multiple sensor protections, altitude compensation and now adds a heat exchanger test. Prints to optional printer. Essential information for installing and maintaining furnaces and boilers all in one device.
-
product
Fabric Drape Tester
TF118
TESTEX Testing Equipment Systems Ltd.
Fabric Drape Tester, to measure and calculate the co-efficiency of drape of fabrics using image processing technology. It can be used to test the drape property of all kinds of fabrics
-
product
Automotive Solutions
One of the most challenging applications in the field of automotive testing is manufacturing electronics. With each successive model year, the number of automated features increases. Every segment of the automotive electronics plays a role in the safety and reliability. These critical applications require high dependability and low maintenance and warranty costs. Our customers don’t have room for error, hardware test systems must perform as designed. Circuit Check provides Automated Test Systems that meet the stringent needs of this marketplace.
-
product
JTAG USB Controller
NetUSB-1149.1/E
The NetUSB-1149.1/E (4 TAPs) is an advanced USB 2.0 and LAN-based controller that can be used in the testing and/or in-system programming (ISP) of devices, boards, or systems compliant with the IEEE-1149.1 standard. The NetUSB-1149.1/E controller supports concurrent (gang) testing and in-system programming of CPLDs and Flash devices at TCK rates of up to 80MHz.The controller connects to the computer either through the USB interface or LAN interface for easy installation at nearby or remote locat...show more -
product
Mechanical Design
In support of system, test and our tooling business, our mechanical engineering team is second to none in offering innovative, yet cost effective solutions for your needs.Whether it is a scalable test fixture solution or a complex, high accuracy torque tooling solution, our team of dedicated mechanical engineers can offer the right solution, with the right level of innovation to give your solution a competitive edge.
-
product
Test Enclosures
The HV test hood, developed by us in accordance with EN50191 standard (erection and operation of fixed and temporary electrical test installations), is designed for testing large quantities in ongoing production. The ergonomic design ensures fatigue-free operation even during repetitive work sequences. Equipped with all safety-relevant functions, such as safety switch and locking of the hood cover during the test sequence, the operator is optimally protected at all times.The interchangeable adapter plate within the test cell allows quick adaptation for different test conditions and test situations.
-
product
High Temperature Wettability Tester
6200Z
This device is a test device that evaluates the wetting stress generated between a plate/round bar and molten metal in an inert gas atmosphere by the wetting balance method.It is possible to analyze not only the quality of wetting but also the wetting phenomenon from the obtained wetting curve.
