-
product
Device Characterization Software with Test Automation
14565B
The Keysight 14565B device characterization software is designed for easy evaluation of portable battery powered device (like 3G handsets, PDA, WLAN, and Bluetooth enable devices) current profiles to ensure long operating life of devices.
-
product
Test Sockets
Smiths Interconnect offers a wide range of spring contacts and design standards for high quality test sockets providing flexibility and fast delivery for optimal cost/performance ratio.
-
product
Altitude Test Chamber
Aircraft and its components are subject to extreme pressure and climatic conditions during flights. These parameters have a significant influence on the functioning of individual components, and they must be monitored and measured for safety reasons. CME Altitude chamber allow for the testing of aerospace components in an environment with controlled pressure, temperature and humidity parameters. An altitude of 100,000 feet [10 mbar] can be simulated in the test space.
-
product
Horizontal Battery Crush Nail Penetration Test Machine
Guangdong Bell Experiment Equipment Co.,Ltd
DGBell's Horizontal Battery Crush Nail Penetration Test MachineApplication: Battery Module / Battery Pack / Battery System crush test, penetration test.Drive Mode: Electro-hydraulic ServoCrush Tool: Semi-cylinder, hemisphere (According to test standard)
-
product
OWON PC Oscilloscope Test Instrument
pc-vds
Shenzhen Chuangxin Instruments Co., Ltd.
- Up to 100MHz bandwidth, and max 1GS/s real-time sample rate- 10M record length- Friendly UI : FFT, or X-Y, and waveform 2 views displayed on the same screen- Multi-trigger option : edge, video, slope, pulse, and alternate- USB isolation - less signal inference, more PC protection- USB bus powering, and LAN remote control (optional)- Ultra-thin body design, easy portability
-
-
product
Loss Test Sets
These instruments combine up to 6 sources, a power meter & optional VFL in one unit.
-
product
DMM Terminal Test Lead
U1580A
The Keysight U1580A test leads are compatible with the U1600A Series handheld digital oscilloscope probes and test leads. These test leads are used for the DMM terminal on the oscilloscopes.
-
product
Relay Test Set
RNT-5A
This is a portable testing kit in one unit, suitable for testing protective relay, over current relay, earth fault relay, protective device, circuit breaker, tripping coils etc. The set is designed for both laboratory and field use.
-
product
UAT Test Management
User Acceptance Testing is the final stage of the Software Development Life Cycle, which is conducted by the users. User Acceptance Testing is extremely important to determine whether the project is working fine as per the end user's point of view. The UAT test management process has to be done in an organized manner to reap maximum benefits from the process.
-
product
Optical, Color And Electrical Integrated Test System
Hangzhou Hopoo Optoelectronics Technology Co., Ltd
Our individually calibrated LED spectroradiometers provide fast and accurate results for actual light measurement applications. It only takes a few seconds to measure and view the results directly on the display, or use the optional analysis and automation software for more in-depth research. Using the HPCS6500 Spectroradiometer, you can measure any or all of the following optical quantities:
-
product
Tactical Radio Test Set
CTS-6100
The CTS-6100 brings an entire test bench to your front lines. Enable your technicians to detect equipment faults and verify operational capabilities at the I- and O-levels, saving valuable diagnostic time and cost.
-
product
IEEE 1641 Test Executive
SigBase
SigBase runtime software supports the simulation, automatic test resource allocation and execution of 1641 test strategies.
-
product
Modular Test System
DMT
The DMT Tester is a modular test system that allows rapid measurement of electrical and non-electrical parameters of functional units. The system also allows basic ICT measurement with optional accessories. It is conceived as modular, with the possibility of integrating a wide range of own and external instruments. The DMT tester is controlled by its own SCADUS software.
-
product
MCB Thermal Verification Test Bench
The test system is a special version of the thermal test test system in the sense that the test jig is primarily designed to hold and connect multi pole MCBs for thermal verification so that each pole can be verified to trip within the IEC time band after the MCB has been riveted. This test ensures the trip verification of MCB so as to trip all the 4 poles at once when overload is detected in one single pole. In short, this is a verification-only bench.
-
product
Test Compliance
MX CTS Series
AMETEK Programmable Power, Inc.
A growing number of electronic products manufactured today have to meet international regulatory requirements for emissions and immunity. This is particularly true for products sold in the European community as well as a growing list of countries in the Far East. The California Instruments MXCTS System provides a cost-effective test solution aimed at verifying higher power product compliance to a number of AC and DC related harmonized test standards. The MXCTS system offers many of the same features and capabilities of the California Instruments CTS Series product line already in use at many EMC labs around the world.
-
product
Test Equipment
Digital Multimeter
*True RMS*2,000 counts*Auto/manual range*Auto power off (APO): 5 mins approx.*Over range display*Non-contact AC voltage detection (NCV) (with audible sound and visible indication)*Auto/manual AC/DC voltage measurement (600V AC/750V DC)*Auto/manual resistor measurement: 0-20MΩ (approximate)*Continuity check: approximate <50Ω buzzer sounds*Diode check*Auto/manual AC/DC current measurement (mA/mA/10A)
-
product
DMM MULTIMETER TEST LEADS
Flexible Vinyl Strain ReliefSoft Silicone Leads48" Length, 18 Gauge1000 Working Volts10 AMP RatedLow-resistance Gold ContactsRetractable Safety Shroud
-
product
Test Fixtures
Test fixtures are a product for the test and the testing of printed circuit boards. The test adapters offered by uwe electronic are suitable for both manual testing and automated testing with vacuum operation. The test fixture can be either fully equipped and wired or delivered without installed components. Pneumatic, Mechanical and Vacuum Fixtures.
-
product
Test Services
INFRAMET offers two types of services in field of electro-optical imaging systems: 1)Trainining and consulting; 2)Test services.
-
product
AIIM Test Charts (Scanner/Microfilm/Digital/ Copier)
AIIM Test Charts (Scanner/Microfilm/Digital/ Copier) by Applied Image - Motion-Rotary Target, Planetary-Static Target, Small Area Target/AIIM MS-303-1980, Small Scanner Resolution Target , Copier Test Array, Rotary Test Target/AIIM X113, Film Strip Target, Eastman Kodak Copier/Scanner Digital Test Target, Small Color MTF Target
-
product
Single Phase Meter Test Bench
Supreme Instrument Laboratories
Single phase meter test bench suitable for calibration & testing of AC Ammeters, AC Volt Meters, AC Single phase Energy Meters, Power Factor Meters & Watt Meters. Other Technical Specifications are as under
-
product
Application Software
Application software is a key element of a premium measurement system. Applying this software approach to a broad range of radiation detector hardware and data acquisition systems, ORTEC software offers comprehensive nuclear measurement solutions that provide integrated hardware control, analysis, and display in a single, easy-to-use package.
-
product
Save your datas during test with Centor Touch
DATASTICK2
The system DATASTICK allows you to save you data on a USB stick in one click, whether you are doing your measurement indoor or outdoor on the field, we propose you a complete mobile solution. All data, results and curve are saved on your USB stick, no more needs of a computer. Connect the DATASTICK to your current gauge CENTOR TOUCH through a dedicated cable.
-
product
Protective Relay Test Set
POM2-6143
POM2 series protective relay test equipment is the best modular designed relay tester with local control system. There are 2 models, the POM2-6143 and POM2-3243, the POM2-6143 with 6×15A and 4×300V.
-
product
Gas-insulated AC Test System
Yangzhou Power Electric Co., Ltd
The test system is used to do AC voltage withstand test and PD measurement for high voltage insulation products, combined electrical equipment, instrument transformers, etc.
-
product
Ultimate Precision Test ATE System
S790 Series2
The Diagnosys S790 Series2, with its high technical specification hardware and technology, represents the ultimate high-performance, precision test ATE system.
-
product
Function Test Module
FX Series
Each FX module is specified one which is suitable for 5 inches bay.You can operate each module on the specified software in PC. It is used USB connection between modules and PC.You can connect MAX 16 modules which include digital IO module,relay module and so on.In case you want to use function inspection system which are combined with several modules, it will implement by our environment generation software(FX-Builder) easily.It is possible to implement by your own software as each module is compatible for Active(X).（Notes）ActiveX is compatible for latest Windows 7 32bit.
-
product
Loss Test Set
HPT-5100
The HPT-5100 represents a significant improvement in technology at a competitive price. This high performance loss test set has advanced features commonly found in instruments costing far more.
-
product
Optics Test Systems
MTF Measuring Device For Endoscopes
Optik Elektronik Gerätetechnik GmbH
Manual MTF measuring device for endoscopes. The measurement setup is based on modular individual components that can be arranged on a breadboard according to the type of endoscope (angle between light entrance and eyepiece).
